Weider Club 16.6st English Manual
Weider Club 16.6st Manual
 |
View all Weider Club 16.6st manuals
Add to My Manuals
Save this manual to your list of manuals |
Weider Club 16.6st manual content summary:
- Weider Club 16.6st | English Manual - Page 1
instructions in this manual before using this equipment. Save this manual for future reference. TABLE OF CONTENTS IMPORTANT PRECAUTIONS 2 BEFORE YOU BEGIN 3 ASSEMBLY 4 ADJUSTMENTS 22 WEIGHT RESISTANCE CHART 24 TROUBLESHOOTING AND MAINTENANCE 25 CABLE DIAGRAMS 26 ORDERING REPLACEMENT PARTS - Weider Club 16.6st | English Manual - Page 2
. 1. Read all instructions in this manual and in the accompanying literature before using the weight system. 2. It is the responsibility of the owner to ensure that all users of the weight system are adequately informed of all precautions. 3. The weight system is intended for home use only. Do - Weider Club 16.6st | English Manual - Page 3
BEFORE YOU BEGIN Thank you for selecting the versatile CLUB WEIDER® 16.6ST weight system. The 16.6ST weight system offers a selection of weight stations designed to develop every major muscle group of the body. Whether your goal is to tone your body, build dramatic - Weider Club 16.6st | English Manual - Page 4
in assembly, use the PART IDENTIFICATION CHART located in the center of this manual. Note: Some small parts may have been preattached for shipping. If a part is not in the parts bag, check to see if it has been pre-attached. • As you assemble the weight system be sure that all parts are oriented as - Weider Club 16.6st | English Manual - Page 5
2. Slide the Assist Upright (74) and the Leg Press Upright (56) onto the indicated M8 x 65mm Carriage Bolts (1) in the Stabilizer (5). The high side of the brackets on the Assist Upright and Leg Press Upright should be on the side shown. Hand tighten four M8 Nylon Locknuts (3) onto the Carriage - Weider Club 16.6st | English Manual - Page 6
4. Press a 50mm Square Inner Cap (27) into the 4 end of the Top Frame (55). Press a 45mm Square Inner Cap (44) into each end of the crossbar on the Top Frame. Press two 25mm Inner Caps (113) into the top of the crossbar. 27 Attach the Top Frame (55) to the Assist Upright (74) and the Leg - Weider Club 16.6st | English Manual - Page 7
a Top Weight (65). Set the Top Weight onto the front stack of Weights (25). Insert both Long Weight Guides (62) into the stack of Weights. Be sure that the holes in the Weight Guides are at the top, as shown. 65 Pin 108 62 Lubricate 64 Pin Groove 8. Press a Weight Tube Bumper - Weider Club 16.6st | English Manual - Page 8
Guides (62) to the Top Frame (55) in the same manner. 9 61 60 73 3 61 60 3 55 62 FRAME ASSEMBLY ARM ASSEMBLY 10. Locate and open the parts bag place onto the Base (4). Note: This will be a tight fit; the Plastic Bushings should fit snugly over the ends of the indicated tube in the Base - Weider Club 16.6st | English Manual - Page 9
ARM ASSEMBLY 12. Press a 25mm Round Inner Cap (49) into one of the Press Arms (46). Press a 45mm Square Inner Cap (44) into the Press Arm. Attach the Press Arm (46) to one side of the Press Frame (17) with two M8 x 60mm Bolts (22) and two M8 Nylon Locknuts (3). Assemble the other Press Arm (46) in - Weider Club 16.6st | English Manual - Page 10
Pivot Arm must 74 be able to pivot easily. 32 49 49 32 84 101 67 56 33 101 16. Press two 25mm x 50mm Inner Caps (107) into the Assist Arm (105). 16 Attach the Assist Arm (105) to the Leg Press Upright (56) with an M10 x 150mm Bolt (106), two M10 - Weider Club 16.6st | English Manual - Page 11
78 102 102 109 109 3 3 109 3 79 18. Locate and open the pulley bag and the parts bags labeled "CABLE ASSEMBLY." 18 During steps 19 through 39, refer to the CABLE DIAGRAMS on pages 26-27 of this manual to verify - Weider Club 16.6st | English Manual - Page 12
20. Wrap the High Cable (58) around a "V"-Pulley 20 (50). Attach the Pulley and a Long Cable Trap (31) to the indicated bracket on the Front Upright (42) with an M10 x 55mm Bolt (86) and an M10 Nylon Locknut (21). Be sure that the Long Cable Trap is positioned to hold the Cable in place. 21. - Weider Club 16.6st | English Manual - Page 13
12 57 58 Bracket 15 58 12 15 21 26. Note: This assembly step shows how to 26 complete the assembly of several pre- attached parts. The 15mm Spacer (7) has been pre-attached ton the Press Frame (17) for shipping purposes. Remove the M10 Nylon Locknut (21), the Spacer, and the - Weider Club 16.6st | English Manual - Page 14
CABLE ASSEMBLY 27. Locate the Low Cable (23). Route the Low 27 Cable under a 90mm Pulley (15). Attach the Pulley to the M10 x 95mm Bolt (not shown) in the - Weider Club 16.6st | English Manual - Page 15
) to the Short Weight Tube (108) with an M8 x 45mm Bolt (24) and an M8 Nylon Locknut (3). 3 38 8 57 58 3 71 108 58 71 8 3 33. Locate the Military Press Cable (72). Attach 33 the Military Press Cable to the other Small "U"-Bracket (71) with an M8 Washer (8) and 3 an M8 Nylon - Weider Club 16.6st | English Manual - Page 16
Pulley and the Assist Arm and that the Cable and Pulley move smoothly. 105 35 74 50 9 112 105 Bracket 31 21 72 76 15 16 - Weider Club 16.6st | English Manual - Page 17
36. Slide an M8 Washer (8) onto an M8 x 75mm Bolt (93). Insert the Bolt through the indicated hole in the Pivot Arm (101). The Bolt must be inserted from the side shown. Fully tighten an M8 Nylon Locknut (3) onto the Bolt. Wrap the Military Press Cable (72) around a 90mm Pulley (15). Attach the - Weider Club 16.6st | English Manual - Page 18
CABLE ASSEMBLY 38. Locate the Leg Press Cable (99). Attach the 38 end of the Leg Press Cable to the Long "U"- Bracket (57) with an M8 Nylon Locknut (3) and - Weider Club 16.6st | English Manual - Page 19
40. Locate and open the parts bag labeled 40 "SEAT ASSEMBLY." Insert an M6 x 60mm Carriage Bolt (92) through the center hole in a Seat Plate (37). Attach the Seat Plate to - Weider Club 16.6st | English Manual - Page 20
SEAT ASSEMBLY 43. Attach the Front Backrest (41) to the Front 43 Upright (42) with two M6 x 65mm Screws (43) and two M6 Washers (10). The Backrest must be oriented as shown. 42 41 43 10 44. Press a 38mm Square Inner Cap (32) into the Front Seat Frame (36). 44 Insert an M6 x 50mm Carriage - Weider Club 16.6st | English Manual - Page 21
the backing from the CLUB WEIDER 48 16.6ST decal and apply it to the weight sys- tem where shown. 49. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in ADJUSTMENTS, beginning on the following page. Before using the weight system, pull each - Weider Club 16.6st | English Manual - Page 22
instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for each exercise at each exercise station may vary from the weight setting. Use the WEIGHT RESISTANCE CHART on page - Weider Club 16.6st | English Manual - Page 23
Upright (42). Attach the Front Seat Frame to the Front Upright with the M8 x 70mm Carriage Bolt (14) and the Seat Knob (40). For some exercises, the Seat (13) must be removed. First, be sure that the chain is not attached to the leg lever. Next, remove the Seat Knob (40 - Weider Club 16.6st | English Manual - Page 24
WEIGHT RESISTANCE CHART This chart shows the approximate weight resistance at each weight station. "Top" refers to the 6.5 lbs. top weight. The other numbers refer to the 12.5 lbs. weight - Weider Club 16.6st | English Manual - Page 25
TROUBLESHOOTING AND MAINTENANCE Make sure all parts are properly tightened each time you use the weight system. Replace any worn parts immediately. The weight system can be cleaned using a damp cloth the cables need to be replaced, see ORDERING REPLACEMENT PARTS on the back cover of this manual. 25 - Weider Club 16.6st | English Manual - Page 26
to be sure that the four cables and the cable traps have been assembled correctly. If the cables have not been correctly routed, the weight system will not function properly and damage may occur. The insets show the proper positioning of the cable traps. The cable traps should be positioned so - Weider Club 16.6st | English Manual - Page 27
Military Press Cable (72) and Leg Press Cable (99) 2 Military Press Cable (72) 6 4 1-Rear Weight Stack 3 5 8-Pivot Arm 7 1-Long "U"-Bracket 3 2 4-Rear Seat Frame Leg Press Cable (99) 27 - Weider Club 16.6st | English Manual - Page 28
PART IDENTIFICATION CHART-Model No. WESY49202 R0103A M10 Nylon Locknut (21) M8 Nylon Locknut (3) M6 Nylon Locknut (2) M10 Washer (9) M8 Washer (8) M6 Washer (10) M4 x 16mm Selftapping Screw ( - Weider Club 16.6st | English Manual - Page 29
M10 x 198mm Bolt (59) M8 x 65mm Carriage Bolt (1) M8 x 70mm CarriageBolt (11) M8 x 70mm CarriageBolt (14) M8 x 75mm Bolt (93) M10 x 75mm Bolt (111) M10 x 80mm Bolt (67) M10 x 85mm Bolt (16) M10 x 95mm Bolt (88) M10 x 105mm Bolt (112) M8 x 120mm Bolt (68) M8 x 150mm Bolt (60) M10 x 150mm Bolt (106) - Weider Club 16.6st | English Manual - Page 30
32mm Round Inner Cap (109) 25mm Inner Cap (113) 25mm Round Cover Cap (70) 25mm Round Inner Cap (49) 19mm Round Inner Cap (34) 25mm Square Inner Cap (6) 38mm Square Inner Cap (32) 45mm Square Inner Cap (44) 25mm x 50mm Inner Cap (107) 50mm Square Inner Cap (27) 50mm Square Outer Cap (51) - Weider Club 16.6st | English Manual - Page 31
PART LIST-Model No. WESY49202 R0103A Key No. Qty. 1 10 2 2 3 42 4 1 5 1 6 1 7 1 8 12 9 10 10 11 11 12 12 5 13 2 14 1 15 14 16 1 17 1 18 6 19 4 20 Manual Exercise Guide Greaes Packet Note: "#" indicates a non-illustrated part. Specifications are subject to change - Weider Club 16.6st | English Manual - Page 32
66 15 2 33 21 30 34 35 29 34 66 30 83 44 28 46 21 6 34 30 9 32 3 49 22 46 17 21 27 16 9 88 3 15 66 15 7 23 21 59 90 EXPLODED DRAWING-Model No. WESY49202 R0103A - Weider Club 16.6st | English Manual - Page 33
(CLUB WEIDER® 16.6ST weight system) 3. The SERIAL NUMBER of the product (see the front cover of this manual) 4. The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING attached at the center of this manual) WEIDER is a registered trademark of ICON Health & Fitness
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
 |
 |
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or find that there
are missing or damaged parts,
we will guarantee you complete
satisfaction through direct assis-
tance from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
Model No. WESY49202
Serial No.
Write the serial number in the space
above for reference.
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manu-
al for future reference.
USER'S MANUAL
Serial Number Decal (Under Seat)
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
WEIGHT RESISTANCE CHART . . . . . . . . . . . . . . . . . . . . . . . . . .24
TROUBLESHOOTING AND MAINTENANCE . . . . . . . . . . . . . . . .25
CABLE DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY
. . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: A PART IDENTIFICATION CHART and a PART LIST/
EXPLODED DRAWING are attached in the center of this manual.