Weider Platinum 600 User Manual
Weider Platinum 600 Manual
 |
View all Weider Platinum 600 manuals
Add to My Manuals
Save this manual to your list of manuals |
Weider Platinum 600 manual content summary:
- Weider Platinum 600 | User Manual - Page 1
you have questions, or if there are missing or damaged parts, we will guarantee complete satisfaction through direct assistance from our and instruc- tions in this manual befVore using this equipment. Save this manual for future reference. USER'S MANUAL Visit our website at www.weiderplatinum - Weider Platinum 600 | User Manual - Page 2
5 ASSEMBLY 6 UPPER CABLE ADJUSTMENT 14 ADJUSTMENTS 15 CABLE DIAGRAM 18 TROUBLESHOOTING 19 EXERCISE GUIDELINES 20 ORDERING REPLACEMENT PARTS Back Cover LIMITED WARRANTY Back Cover Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of this manual - Weider Platinum 600 | User Manual - Page 3
PLACEMENT The decals shown here have been placed on the resistance system. If a decal is missing or illegible, please call our Customer Service Department tollfree at 1-877-992-5999, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time, to order a free replacement decal. Apply the decal in the - Weider Platinum 600 | User Manual - Page 4
to be used for pull-up exercises. Do not hang on the crossbar. WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. ICON assumes no - Weider Platinum 600 | User Manual - Page 5
WEIDER® PLATINUM 600 reading this manual, please call our Customer Service Department toll review the drawing below and familiarize yourself with the parts that are labeled. ASSEMBLED DIMENSIONS: Height: 82 in. Width: 66 in. Depth: 80 in. Console Upright Storage Knob Backrest Seat Leg Lever Crossbar - Weider Platinum 600 | User Manual - Page 6
. • For help identifying small parts, use the PART IDENTIFICATION CHART. Note: Some small parts may have been pre-attached for shipping. If a part is not in the parts bag, check to see if it has been pre-attached. • Tighten all parts as you assemble them, unless instructed to do otherwise. • As - Weider Platinum 600 | User Manual - Page 7
2. Attach the Upright (3) to the Base (1) with two 2 M10 x 66mm Carriage Bolts (89), two M10 x 72mm Bolts (87), and four M10 Nylon Locknuts (71) as shown. Note: This step will be easier to complete if the Upright and Base are tipped on their sides. 3 87 71 71 71 1 89 3. Attach the Foot - Weider Platinum 600 | User Manual - Page 8
CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. Pull the excess lower wire harness (A) out of the Mech Assembly (6) and push it and and a 1/2" Nylon Jamnut (78). Do not tighten the Jamnut yet. Attach the Mech Assembly (6) to the Base (1) with four M10 Nylon Locknuts (71). Tighten the 1/2" Nylon - Weider Platinum 600 | User Manual - Page 9
that the serrated edge of the Flange Nuts are against the Seat Carriage. While a second person presses down on the Seat (41), hold the wheel assembly firmly against the bottom of the Bench Rail (23) and properly tighten the M8 Flange Nuts (47). Make sure that three threads are extending past - Weider Platinum 600 | User Manual - Page 10
(50). Make sure that the Eyebolts (51) are oriented as shown in the inset drawing. If they are not, turn the Lat Tower Crossbar around and reattach it. 12. Attach a Large Pulley (17) and the Pulley Plate (18) to the Upright (3) with an M12 x 62mm Button Bolt (80) and - Weider Platinum 600 | User Manual - Page 11
the upper cable (B), which is attached inside 13 of the Mech Assembly (6), up between the Upright (3) and the Pulley Plate (18 (72) used in steps 12 and 13. 14. Attach a Small Guide Spacer (56), a Large Guide Spacer (57), and two Bar Guides (55) to the Lat Tower (5) with an M10 x 152mm Bolt - Weider Platinum 600 | User Manual - Page 12
17. Hold a Large Pulley (17) inside the upper cable (B). Attach the Pulley to a Pulley Bracket (10) with an M12 x 58mm Button Bolt (81) and an M12 Nylon Locknut (72). Make sure that the cable is routed as shown in the CABLE DIAGRAM on page 18. Screw two 3/8" x 38mm Tension Screws (106) into the two - Weider Platinum 600 | User Manual - Page 13
. The use of the remaining parts will be explained in ADJUSTMENTS, beginning on page 15. Before using the resistance system, pull the long cable a few times to be sure that it moves smoothly over the pulleys. If the cable does not move smoothly, find and correct the problem. IMPORTANT: If the cables - Weider Platinum 600 | User Manual - Page 14
UPPER CABLE ADJUSTMENT After completing the assembly of the resistance system, the tension on the upper cable (B) will need to be adjusted. Also, the upper cable can stretch slightly when it is - Weider Platinum 600 | User Manual - Page 15
GUIDELINES on page 18 for important information about how to get the most benefit from your exercise program. Also, refer to the accompanying exercise guide to see the correct form for each exercise. Make sure all parts are properly tightened each time the resistance system is used. Replace worn - Weider Platinum 600 | User Manual - Page 16
Cables (60), with two Cable Clips. 67 Note: A lat bar is an optional accessory for the resistance system. To purchase a lat bar, call our Customer Service Department toll-free at 1-877-992- 5999 and ask for model number WEMC0442. ATTACHING THE LEG LEVER To use the Leg Lever (32), attach the - Weider Platinum 600 | User Manual - Page 17
the Backrest against the Upright (3). For row exercises, remove the Backrest (40). Hold the Backrest Lift the Front Leg toward the Lat Tower Crossbar (49), and tighten the Storage Knob into the plug in the transformer when using the resistance system, and unplug the transformer when finished. Rod - Weider Platinum 600 | User Manual - Page 18
CABLE DIAGRAM The cable diagram shows the proper routing of the upper cable (B). Use the diagram to make sure that the cable has been assembled correctly. If the cable has not been correctly routed, the resistance system will not function properly and damage may occur. The numbers show the correct - Weider Platinum 600 | User Manual - Page 19
TROUBLESHOOTING CLEANING THE BAR GUIDES Over time, dust may build up on the Bar Guides (55), causing a squeaking noise as the resistance system is used. If this occurs, wipe off the Bar Guides with a damp cloth and a mild, non-abrasive detergent. Do not use solvents. ADJUSTING THE RESISTANCE When - Weider Platinum 600 | User Manual - Page 20
only the appropriate parts of the body. Exercising in an uncontrolled manner will leave you feeling exhausted. On the exercise guide accompanying this manual you will find photographs showing the correct form for several exercises, and a list of the muscles affected. Refer to the muscle chart on the - Weider Platinum 600 | User Manual - Page 21
keep a record of each workout. The chart on pages 22 and 23 of this manual can be photocopied and used to schedule and record your workouts. List the date, the exercises performed, the resistance used, and the numbers of sets and repetitions completed. Record your weight and key body measurements at - Weider Platinum 600 | User Manual - Page 22
MONDAY Date: / / EXERCISE WEIGHT SETS REPS TUESDAY Date: / / WEDNESDAY Date: / / AEROBIC EXERCISE EXERCISE WEIGHT SETS REPS THURSDAY Date: / / FRIDAY Date: / / AEROBIC EXERCISE EXERCISE WEIGHT SETS REPS Make photocopies of this page for scheduling and recording your workouts. 22 - Weider Platinum 600 | User Manual - Page 23
MONDAY Date: / / EXERCISE WEIGHT SETS REPS TUESDAY Date: / / WEDNESDAY Date: / / AEROBIC EXERCISE EXERCISE WEIGHT SETS REPS THURSDAY Date: / / FRIDAY Date: / / AEROBIC EXERCISE EXERCISE WEIGHT SETS REPS Make photocopies of this page for scheduling and recording your workouts. 23 - Weider Platinum 600 | User Manual - Page 24
PART IDENTIFICATION CHART Refer to the drawings below to identify small parts used in assembly. The number in parentheses by each drawing is the key number of the part, from the PART LIST in the center of this manual. Note: Some small parts may have been pre-attached. If a part is not in the parts - Weider Platinum 600 | User Manual - Page 25
Mech Assembly 7 1 Front Mech Cover 8 1 Back Mech Cover 9 1 Resistance Bar 10 2 Pulley Bracket 11 4 M6 x 16mm Screw 12 1 Transformer 13 User's Manual Exercise Guide Exercise Decal Large Allen Wrench Small Allen Wrench Note: "#" indicates a non-illustrated part. Specifications - Weider Platinum 600 | User Manual - Page 26
70 73 76 96 41 42 50 27 66 52 49 51 25 70 71 40 76 16 71 67 27 60 51 106 75 11 11 95 45 46 44 102 46 68 47 95 45 52 39 25 71 82 61 72 16 10 81 70 47 48 105 45 70 69 43 105 36 46 44 44 45 60 38 19 103 103 103 98 100 98 5 77 17 59 54 72 17 85 - Weider Platinum 600 | User Manual - Page 27
WEIDER® PLATINUM 600 resistance system) • The SERIAL NUMBER of the product (see the front cover of this manual) • The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING in the center of this manual) LIMITED WARRANTY ICON Health & Fitness authorized service center;
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
 |
 |
CAUTION
Read all precautions and instruc-
tions in this manual before
using this equipment. Save this
manual for future reference.
Model No. WESY68630
Serial No.
Write the serial number in the
space above for future reference.
Serial Number Decal (under seat)
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts, we
will guarantee complete satis-
faction through direct assis-
tance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
customer hot line will provide
immediate assistance, free of
charge.
CUSTOMER HOT LINE:
1-877-992-5999
Mon.–Fri., 6 a.m.–6 p.m. MST
Visit our website at
www.weiderplatinum.com
USER’S MANUAL