Home » Weider Manuals » Exercise and Fitness » Weider Pro 2250 » Manual Viewer

Weider Pro 2250 English Manual

Weider Pro 2250 Manual

Get Weider Pro 2250 PDF manuals and user guides

View all Weider Pro 2250 manuals

Add to My Manuals
Save this manual to your list of manuals

Weider Pro 2250 manual content summary:

Weider Pro 2250 | English Manual - Page 1
. WEIGHT SYSTEM EXERCISER User's Manual Serial Number Decal (under seat) • Assembly • Adjustments • Troubleshooting • Part List and Drawing CAUTION Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. Patent Pending Sears
Weider Pro 2250 | English Manual - Page 2
ASSEMBLY 5 ADJUSTMENTS 13 WEIGHT RESISTANCE CHART 15 TROUBLESHOOTING 16 CABLE DIAGRAMS 17 EXERCISE GUIDELINES 18 ORDERING REPLACEMENT PARTS Back Cover FULL 90-DAY WARRANTY Back Cover Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached to the center of this manual
Weider Pro 2250 | English Manual - Page 3
weights are raised. The weights will fall with great force. Decal 1 WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. Sears
Weider Pro 2250 | English Manual - Page 4
WEIDER® PRO 2250 weight system. The weight system offers an impressive array of weight weight system (see the front cover of this manual for the location of the decal). Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled. ASSEMBLED
Weider Pro 2250 | English Manual - Page 5
assembly is completed. • Tighten all parts as you assemble them, unless instructed to do otherwise. • As you assemble the weight system, make sure all parts are oriented as shown in the drawings. • For help identifying small parts, use the PART IDENTIFICATION CHART at the center of this manual
Weider Pro 2250 | English Manual - Page 6
(1) in the Base (4). Hand tighten 2 two M8 Nylon Locknuts (3) onto the Carriage Bolts. Do not tighten the Locknuts yet. 42 3 3. Attach the two Weight Guides (62) inside of the 3 Stabilizer (5) with two M10 x 67mm Bolts (11), two M10 Washers (9), two 13mm Spacers (61), and two M10 Nylon
Weider Pro 2250 | English Manual - Page 7
two M8 x70mm Bolts (81), a Support Plate (84), and two M8 Nylon Locknuts (3). 81 84 Attach the upper ends of the Weight Guides (62) to the Top Frame (55 x 75mm Bolts (22), four M10 Washers (9), and two M10 Nylon Locknuts (21). Assemble the Left Press Arm (73) in the same manner. 5 Hole 17 21 9
Weider Pro 2250 | English Manual - Page 8
of the Left Arm is behind the indicated bracket on the Top Frame. Set two 25mm Retainers (69) on top of a 25mm Round Cover Cap Cable Assembly 8 8. During steps 8 through 19, see the CABLE DIAGRAMS on page 17 of this manual to verify proper cable routing. Locate the Short Cable (58). Lay the Cable
Weider Pro 2250 | English Manual - Page 9
(16), the M10 Washer (9), and the M10 Nylon Locknut (21). 10 21 15 58 17 9 16 11. Route the Short Cable (58) under a 90mm Pulley 11 (15). Attach the Pulley and a Cable Trap (66) to the upper hole in the Front Upright (42) with an M10 x 95mm Bolt (71), an M10 Washer
Weider Pro 2250 | English Manual - Page 10
(50) to the Left Arm (47) with an M10 x 58mm Bolt (7) and an M10 Nylon Locknuts (21). Make sure that the Long Cable Trap is positioned to hold the Cable in the groove of the "V"-pulley. Repeat this step with the Right Arm (48). 48 47 7 6 21 50 23 47 16. Route
Weider Pro 2250 | English Manual - Page 11
Bracket 15 83 23 19. Attach the Long Cable (23) to the Small "U"- 19 bracket ( Cable so that two threads are showing past the nut. 23 Attach the Small "U"-bracket (67) to the Weight Tube (63) with an M8 x 45mm Bolt (72) and an 3 67 M8 Nylon Locknut (3). 72 8 63 3 23 3 67 Seat Assembly
Weider Pro 2250 | English Manual - Page 12
a Pad Tube (28) into the Seat Frame (36). 23 Wet the Pad Tube with soapy water. Slide two Small Pads (30) onto the Pad Tube. Assemble the other Pad Tube (28) to the Leg Lever (29) in the same manner. 30 29 36 28 30 24. Rest the Seat Frame (36
Weider Pro 2250 | English Manual - Page 13
it by tightening the cables; see TROUBLESHOOTING on page 16. ADJUSTMENTS The instructions below describe how each part of the weight system can be adjusted. See the exercise guide accompanying this manual to see how the weight system should be set up for each exercise. IMPORTANT: When attaching
Weider Pro 2250 | English Manual - Page 14
upright (see ATTACHING AND REMOVING THE SEAT, above). Remove the Weight Pin (not shown) from the weight stack. Attach the Short Cable (58) to the Eyebolt (35) with a Cable Clip (53). Note: The Weight Pin must also be removed when removing the Short Cable from the Eyebolt. 40 36 13 86 42 Pin 29
Weider Pro 2250 | English Manual - Page 15
station may vary due to differences in individual weight plates, as well as friction between the cables, pulleys, and weight guides. Do not use the top weight by itself; the weight system may not function properly. WEIGHT PLATES PRESS ARM (lbs.) BUTTERFLY ARM (lbs.) LEG LEVER HIGH PULLEY LOW
Weider Pro 2250 | English Manual - Page 16
TROUBLESHOOTING Inspect and tighten all parts each time the weight system is used. Replace any worn parts immediately. The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type of cable used on the weight
Weider Pro 2250 | English Manual - Page 17
CABLE DIAGRAMS The cable diagrams show the proper routing of the Long Cable (23) and the Short Cable (58). Use the diagram to make sure that the two cables and the cable traps have been assembled correctly. If the cables have not been correctly routed, the weight system will not function properly
Weider Pro 2250 | English Manual - Page 18
essential part of an effective exercise program. This requires moving through the full range of motion for each exercise, and moving only the appropriate parts of the body. Exercising in an uncontrolled manner will leave you feeling exhausted. On the exercise guide accompanying this manual you will
Weider Pro 2250 | English Manual - Page 19
of sets and repetitions completed. Record your weight and key body measurements at the end of every month. Remember, the key to achieving the greatest results is to make exercise a regular and enjoyable part of your everyday life. A B C D E F G H I J K L M N O P Q R S T U V W X MUSCLE CHART
Weider Pro 2250 | English Manual - Page 20
PART IDENTIFICATION CHART-Model No. 831.159301 R0304A M4 Washer (82) M6 Washer (10) M8 Washer (8) M6 x 16mm Screw (18) M4 x 20mm Screw (56) M8 x 45mm Bolt (72)
Weider Pro 2250 | English Manual - Page 21
M10 x 198mm Bolt (59) M6 x 65mm Screw (43) M10 x 67mm Bolt (11) M8 x 70mm Bolt (81) M10 x 67mm Carriage Bolt (14) M10 x 75mm Bolt (22) M10 x 80mm Bolt (16) M10 x 90mm Bolt (85) M10 x 95mm Bolt (71) M8 x 117mm Bolt (68) M10 x 155mm Bolt (60)
Weider Pro 2250 | English Manual - Page 22
Bolt Left Press Arm Butterfly Arm Bushing 25mm Plastic Bushing Top Weight 38mm Round Inner Cap 25mm Round (thick) Inner Cap 50mm x 70mm Inner Cap M8 x 57mm Bolt M8 x 70mm Bolt M4 Washer M10 x 45mm Bolt Support Plate M10 x 90mm Bolt M8 x 67mm Carriage Bolt Grease Packet User's Manual Exercise Guide
Weider Pro 2250 | English Manual - Page 23
EXPLODED DRAWING-Model No. 831.159301 R0304A 68 21 20 15 66 44 81 78 21 21 55 3 12 27 15 7 23 50 74 6 74 48 69 70 21 69 27 84 13 83 34 30 37 78 15 44 32 18 38 18 85 80 7 34 30 29 50 9 6 21 31 3 10 2 35 28 77 30 70 47 33 54 31 21 40 86 10 36 24 28 30 34 34 9 60
Weider Pro 2250 | English Manual - Page 24
in material or workmanship in this WEIGHT SYSTEM EXERCISER, contact the nearest Sears Service Center throughout the United States and Sears will repair or replace the WEIGHT SYSTEM EXERCISER, free of charge. This warranty does not apply when the WEIGHT SYSTEM EXERCISER is used commercially or for