Weider Pro 3650 English Manual
Weider Pro 3650 Manual
 |
View all Weider Pro 3650 manuals
Add to My Manuals
Save this manual to your list of manuals |
Weider Pro 3650 manual content summary:
- Weider Pro 3650 | English Manual - Page 1
our customer hot line will provide immediate assistance, free of charge. CUSTOMER HOT LINE: 1-800-999-3756 Mon.-Fri., 6 a.m.-6 p.m. MST CAUTION Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. Patent Pending Visit our website - Weider Pro 3650 | English Manual - Page 2
YOU BEGIN 4 ASSEMBLY 5 ADJUSTMENTS 22 WEIGHT RESISTANCE CHART 24 TROUBLESHOOTING 25 CABLE DIAGRAMS 26 ORDERING REPLACEMENT PARTS Back Cover LIMITED WARRANTY Back Cover Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of this manual. Remove the - Weider Pro 3650 | English Manual - Page 3
free replacement decal. Apply the decal in the location shown. 6. Keep children under 12 and pets away from the weight system at all times. 7. Keep hands and feet away from moving parts. 8. Always wear athletic shoes for foot protection. 9. The weight system is designed to support a a maximum user - Weider Pro 3650 | English Manual - Page 4
the decal). For your benefit, read this manual carefully before using the weight system. If you have additional questions, please call our Customer Service Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled. Lat Bar High Pulley Station - Weider Pro 3650 | English Manual - Page 5
assemble the weight system, make sure that all parts are oriented exactly as shown in the drawings. Tightening Parts Tighten all parts as you assemble them, unless instructed to do otherwise. Questions? If you have questions after reading the assembly instructions, please call our Customer Service - Weider Pro 3650 | English Manual - Page 6
1 1. Make sure that you understand all of the information on page 5 before you begin assembling the weight system. 2 24 120 14 Locate and open the parts bags labeled "FRAME ASSEMBLY 1" and "FRAME ASSEMBLY 2." See the inset drawing. Attach the Base Cap (24) to the Short Base (2) with two M4 - Weider Pro 3650 | English Manual - Page 7
4. Press a 38mm Square Inner Cap (67) into the 4 Upright Extension (12). Attach the Upright Extension (12) to the Butterfly Upright (3) with two M10 x 95mm Bolts (92), two M10 Washers (91), and two M10 Nylon Locknuts (87). Make sure the warning decals on each side of the Extension are right-side - Weider Pro 3650 | English Manual - Page 8
7. Press a 50mm x 75mm Inner Cap (58) into the top of the Squat Upright (4). Press two 25mm Round 7 Outer Cap (121) onto the Upright. Slide the Squat Upright onto the two indicated M10 x 65mm Carriage Bolts (110) in the Long Base (101). Finger tighten an M10 Nylon Locknut (87) onto each - Weider Pro 3650 | English Manual - Page 9
the Top Weight onto the Weight Guides (42). Make sure that the Top Weight is turned so the grooved side is facing downward. Apply a number "10" decal to the Top Weight (45) in the location shown. Apply decals with the numbers 20 through 110 to the ten Weights (44). Assemble the other weight stack - Weider Pro 3650 | English Manual - Page 10
) as shown. Do not tighten the Bolts and Locknuts yet. Attach the four Weight Guides (42) to the Top Frame (6) with two M10 x 165mm Bolts (30) the M10 Nylon Locknuts (87) used in steps 4-13. ARM ASSEMBLY 14. Open the parts bag labeled "ARM ASSEMBLY." Press three 40mm x 50mm Inner Caps (21) into the - Weider Pro 3650 | English Manual - Page 11
IMPORTANT: Refer to the Cable Identification 18 Chart on page 26 for help identifying the cables. Do not overtighten the bolts and nuts attaching the pulleys. The pulleys must be able to turn freely. Locate and open the parts bags labeled "CABLE ASSEMBLY" and "PULLEYS." 78 74 30 87 Lubricate - Weider Pro 3650 | English Manual - Page 12
an M12 Nut (118) halfway onto the end of the Swivel High Cable (74). Screw the end of the Cable two full turns into the Weight Tube. Then, tighten the M12 Nut against the Washer. 23. Locate the Swivel Cable (17), which is 2930mm 23 long and has an eyelet on - Weider Pro 3650 | English Manual - Page 13
24. Remove the preattached 90mm Pulleys (78) from the Offset Double "U"-bracket (61). 24 Wrap the Swivel Cable (17) around a 90mm Pulley (78). Attach the Pulley to the Offset Double "U"bracket (61) with an M10 x 45mm Bolt (93) and an M10 Nylon Locknut (87). 25. Wrap the Swivel Cable (17) around a - Weider Pro 3650 | English Manual - Page 14
29. Wrap the Lat Cable (88) around a 90mm Pulley 29 (78). Attach the Pulley and a Long Cable Trap (102) to the Top Frame (6) with an M10 x 50mm Bolt (100) and an M10 Nylon Locknut (87). Make sure the Cable Trap is turned to hold the Cable in the groove of the Pulley. 30. Remove the - Weider Pro 3650 | English Manual - Page 15
34. Remove the preattached 90mm Pulleys (78) from the Double "U"-bracket (62). 34 Wrap the Butterfly Cable (69) under a 90mm Pulley (78). Attach the Pulley to the Double "U"-bracket (62) with an M10 x 45mm Bolt (93) and an M10 Nylon Locknut (87). 69 78 87 93 62 35. Wrap the Butterfly Cable (69) - Weider Pro 3650 | English Manual - Page 16
39. Route the Leg Lever Cable (75) under a 115mm 39 Pulley (119). Attach the Pulley and a Large Cable Trap (113) to the indicated side of the Butterfly Upright (3) with an M10 x 95mm Bolt (92), an M10 Washer (91), and an M10 Nylon Locknut (87). Make sure that the Large Cable Trap is turned to - Weider Pro 3650 | English Manual - Page 17
(101) with an M10 x 45mm Bolt (93) and an M10 Nylon Locknut (87). 46. Route the Swivel Low Cable (72) under the indicated stack of Weights (44). Wrap the Swivel Low Cable (72) under a 90mm Pulley (78). Attach the Pulley to the indicated bracket on the Long Base (101) with an - Weider Pro 3650 | English Manual - Page 18
49. Wrap the Swivel Low Cable (72) over a 90mm Pulley (78). Attach the Pulley and a Cable Trap (68) 49 between the lower set of holes in the "U"-bracket (64) with an M10 x 50mm Bolt (100) and an M10 Nylon Locknut (87). Make sure that the Cable Trap is turned to hold the Cable in the groove of - Weider Pro 3650 | English Manual - Page 19
. Then, tighten the M12 Nut (118) against the 50mm Washer (1). Remove the Weight Pin and set the Top Weight back on the weight stack. Replace the Pin. SEAT ASSEMBLY 56. Locate and open the parts bag labeled "SEAT ASSEMBLY." Insert the Pad Tube (23) into the square hole in the Seat Upright (9). Wet - Weider Pro 3650 | English Manual - Page 20
57. Press two 20mm x 40mm Inner Caps (116) and a 57 25mm x 40mm Square Inner Cap (117) into the Seat Bracket (11). Attach the Seat (16) to the Seat Bracket (11) with two M6 x 16mm Screws (114), an M6 x 35mm Screw (99), and an M6 Washer (97). Turn the indicated Adjustment Handle (65) - Weider Pro 3650 | English Manual - Page 21
one of the cables does not move smoothly, find and correct the problem. IMPORTANT: If the cables are not properly installed, they may be damaged when heavy weight is used. See the CABLE DIAGRAMS on page 26 and 27 of this manual for proper cable routing. If there is any slack in the cables - Weider Pro 3650 | English Manual - Page 22
ADJUSTMENTS The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for various exercises. IMPORTANT: When attaching the lat bar, row bar, or handle, make sure that the - Weider Pro 3650 | English Manual - Page 23
ADJUSTING THE SQUAT ARM, SEAT, OR BUTTERFLY BACKREST To adjust the height of the Squat Arm (32), first turn the Adjustment Knob (115) on the Squat Bracket (37) counterclockwise several turns to loosen it. Next, pull the Handle and slide the Squat Bracket up or down to the desired position. Engage - Weider Pro 3650 | English Manual - Page 24
listed is the resistance for each butterfly arm. Note: The actual resistance at each weight station may vary due to differences in individual weight plates as well as friction between the cables, pulleys, and weight guides. WEIGHT Top 1 2 3 4 5 6 7 8 9 10 HIGH PULLEY (lbs.) 14 25 38 48 61 68 80 96 - Weider Pro 3650 | English Manual - Page 25
TROUBLESHOOTING Make sure all parts are properly tightened each time the weight system is used. Replace any worn parts immediately. The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type of cable used - Weider Pro 3650 | English Manual - Page 26
the routes of the cables. Use the diagrams to make sure that the cables have been assembled correctly. IMPORTANT: If the cables have not been correctly routed, the weight system will not function properly and damage may occur. Cable Identification Chart Butterfly Cable (69)-1475mm Swivel Low Cable - Weider Pro 3650 | English Manual - Page 27
Leg Lever Cable (75) 3 4 2 1 Swivel Low Cable (72) 3 6 8 1 2 5 4 7 9 Swivel Cable (17) 1 3 5 2 4 27 - Weider Pro 3650 | English Manual - Page 28
PART IDENTIFICATION CHART-Model No. WESY39523 R0403A 12mm Spacer (89) 50mm Washer (1) M10 Washer (91) 19mm Spacer (98) Cable Clip (83) M8 Washer (90) M6 Washer (97) M4 - Weider Pro 3650 | English Manual - Page 29
M10 x 50mm Bolt (100) M10 x 45mm Bolt (93) M6 x 35mm Bolt (99) M10 x 20mm Bolt (86) M8 x 20mm Shoulder Bolt (103) M8 x 20mm Button Head Screw (51) M4 x 20mm Selftapping Screw (14) M6 x 16mm Screw (114) M10 x 60mm Bolt (59) M10 x 65mm Bolt (18) M10 x 65mm Carriage Bolt (110) M10 x 70mm Bolt (85) M10 - Weider Pro 3650 | English Manual - Page 30
50mm x 75mm Inner Cap (58) 50mm x 70mm Inner Cap (95) 50mm Square Inner Cap (105) 25mm x 40mm Inner Cap (117) 40mm x 50mm Inner Cap (21) 38mm Square Inner Cap (67) 25mm Round Inner Cap (29) 20mm x 40mm Inner Cap (116) 25mm Round Outer Cap (121) - Weider Pro 3650 | English Manual - Page 31
M8 Nylon Locknut Squat Backrest 135mm Handgrip Squat Bracket Squat Slider Roller Roller Bearing Squat Knee Rest Weight Guide Weight Tube Weight 45 2 46 1 47 1 48 2 49 4 50 2 51 8 52 2 53 User's Manual Exercise Guide Grease Package Note: "#" indicates a non-illustrated part. Specifications are subject - Weider Pro 3650 | English Manual - Page 32
EXPLODED DRAWING-Model No. WESY39523 R0403A 58 18 91 58 78 31 92 18 87 87 92 91 87 78 85 89 91 7 91 31 87 78 68 100 52 91 87 30 68 87 91 87 89 91 91 87 89 18 93 87 91 87 93 102 87 91 100 6 103 87 76 119 119 100 69 60 26 60 70 34 100 34 69 91 58 95 87 89 85 91 18 88 18 - Weider Pro 3650 | English Manual - Page 33
ORDERING REPLACEMENT PARTS To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday WEIDER® PRO 3650 weight system) • The SERIAL NUMBER of the product (see the front cover of this manual) • The KEY NUMBER and DESCRIPTION of the part(s) (see the PART
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
 |
 |
USER'S MANUAL
QUESTIONS?
As a manufacturer, we are
committed to providing complete
customer satisfaction. If you
have questions, or if parts are
missing, we will guarantee com-
plete satisfaction through assis-
tance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The technicians on our cus-
tomer hot line will provide imme-
diate assistance, free of charge.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
Model No. WESY39523
Serial No.
Write the serial number in the
space above for future reference.
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
www.weiderfitness.com
new products, prizes,
fitness tips, and much more!
Serial Number Decal (Under Seat)
Patent Pending