Weider Pro 4850 Canadian English Manual

Weider Pro 4850 Manual

Get Weider Pro 4850 PDF manuals and user guides View all Weider Pro 4850 manuals
Add to My Manuals
Save this manual to your list of manuals

Weider Pro 4850 manual content summary:

  • Weider Pro 4850 | Canadian English Manual - Page 1
    . Write the serial number in the space above for reference. WEIGHT SYSTEM EXERCISER User's Manual Serial Number Decal (under seat) · Assembly · Adjustments · Troubleshooting · Part List and Drawing CAUTION Read all precautions and instructions in this manual before using this equipment. Save this
  • Weider Pro 4850 | Canadian English Manual - Page 2
    YOU BEGIN 4 ASSEMBLY 5 ADJUSTMENTS 22 WEIGHT RESISTANCE CHART 24 TROUBLESHOOTING 25 CABLE DIAGRAMS 26 ORDERING REPLACEMENT PARTS Back Cover FULL 90-DAY WARRANTY Back Cover Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of this manual. Remove the
  • Weider Pro 4850 | Canadian English Manual - Page 3
    each time you use the weight system. Replace any worn parts immediately. 6. Keep children under 12 and pets away from the weight system at all times. 14. Make sure that the cables remain on the pulleys at all times. If the cables bind while you are exercising, stop immediately and make sure
  • Weider Pro 4850 | Canadian English Manual - Page 4
    , or improve your cardiovascular system, the PRO 4850 weight system will help you to achieve the specific results you want. For your benefit, read this manual carefully before using the weight system. If you have questions after reading this manual, call 1-800-4-MY-HOME® (1-800-469-4663). To
  • Weider Pro 4850 | Canadian English Manual - Page 5
    As you assemble the weight system, make sure that all parts are oriented exactly as shown in the drawings. Tightening Parts Tighten all parts as you assemble them, unless instructed to do otherwise. Questions? If you have questions after reading the assembly instructions, please call 1-800-4-MY-HOME
  • Weider Pro 4850 | Canadian English Manual - Page 6
    1 1. Make sure that you understand all of the information on page 5 before you begin assembling the weight system. Locate and open the parts bags labeled "FRAME ASSEMBLY 1" and "FRAME ASSEMBLY 2." Press a 2" Square Inner Cap (105) into the open end of the Long Base (120). Insert eight 5/16
  • Weider Pro 4850 | Canadian English Manual - Page 7
    4. Press a 1 1/2" Square Inner Cap (67) into the 4 square tube on the Butterfly Upright (3). Slide the Butterfly Upright (3) onto the two indicated 5/16" x 2 1/2" Carriage Bolts (110) in the Short Base (2). Finger tighten a 5/16" Nylon Locknut (86) onto each Carriage Bolt. Do not tighten the
  • Weider Pro 4850 | Canadian English Manual - Page 8
    7. Press a 2" x 3" Inner Cap (58) into the top of the Squat Upright (4). Slide the Squat Upright onto the 7 two indicated 5/16" x 2 1/2" Carriage Bolts (110) in the Long Base (120). Finger tighten a 5/16" Nylon Locknut (86) onto each Carriage Bolt. Do not tight- en the Nylon Locknuts yet.
  • Weider Pro 4850 | Canadian English Manual - Page 9
    the Top Weight onto the Weight Guides (42). Make sure that the Top Weight is turned so the grooved side is facing downward. Apply a number "10" decal to the Top Weight (45) in the location shown. Apply decals with the numbers 20 through 110 to the ten Weights (44). Assemble the other weight stack
  • Weider Pro 4850 | Canadian English Manual - Page 10
    (86) as shown. Do not tighten the Bolts and Locknuts yet. Attach the four Weight Guides (42) to the Top Frame (6) with two 3/8" x 6 1/2" Bolts (95) 3/8" Nylon Locknuts (87) used in steps 2-13. ARM ASSEMBLY 14. Open the parts bag labeled "ARM ASSEMBLY." Press three 1 1/2" x 2" Inner Caps (21) into
  • Weider Pro 4850 | Canadian English Manual - Page 11
    18. IMPORTANT: Refer to the Cable Identification 18 Chart on page 26 for help identifying the cables. Do not overtighten the bolts and nuts attaching the pulleys. The pulleys must be able to turn freely. Locate and open the parts bags labeled "CABLE ASSEMBLY" and "PULLEYS." 78 74 30 87
  • Weider Pro 4850 | Canadian English Manual - Page 12
    the groove of the Pulley. 21. Wrap the Swivel High Cable (74) over a 4 1/2" 21 Pulley (119). Attach the Pulley inside of the indicat- ed bracket on the Top Frame (6) with 3/8" x 1 3/4" Bolt (93) and a 3/8" Nylon Locknut (87). 74 87 100 78 68 31 31 6 93 87 22. Lift the Weight Tube (43) and the
  • Weider Pro 4850 | Canadian English Manual - Page 13
    is 89 1/4" long and has a ball on one end and an eyelet on the other. Route the eyelet end of the Cable up through the Butterfly Top Frame (7) and around a 3 1/2" Pulley (78). Attach the Pulley inside of the Butterfly Top Frame with a 3/8" x 2 3/4" Bolt (101), two 3/8" Washers (91), two 1/2" Spacers
  • Weider Pro 4850 | Canadian English Manual - Page 14
    the indicated bracket on the Butterfly Upright (3) with a 3/8" x 2 1/2" Bolt (18) and a 3/8" Nylon Locknut (87). Make sure that the Long Cable Trap is turned to hold the Cable in the groove of the Pulley. 14 88 113 78 102 93 6 100 68 78 87 88 63 86 90 90 59 7 88 86 69 103
  • Weider Pro 4850 | Canadian English Manual - Page 15
    69 78 93 87 62 35. Wrap the Butterfly Cable (69) over a "V"-pulley (55). 35 Attach the Pulley and a Long Cable Trap (102) to 18 the other bracket on the on one end and a threaded pin on the other end. Route the eyelet end of the Cable through the Seat Upright (9) and attach it to the tab
  • Weider Pro 4850 | Canadian English Manual - Page 16
    that has an eyelet on one end and a ball on the other end. Route the eyelet end of the Cable through the cage on the Long Base (120) and through the Swivel Upright (5) as shown. Attach a 3 1/2" Pulley (78) to the indicated bracket on the Long Base (120) with 3/8" x 1 3/4" Bolt (93) and a 3/8" Nylon
  • Weider Pro 4850 | Canadian English Manual - Page 17
    on the Long Base (120) with a 3/8" x 1 3/4" Bolt (93) and a 3/8" Nylon Locknut (87). 46. Route the Swivel Low Cable (72) under the indicated stack of Weights (44). Wrap the Swivel Low Cable (72) under a 3 1/2" Pulley (78). Attach the Pulley to the indicated bracket on the Long Base (120) with
  • Weider Pro 4850 | Canadian English Manual - Page 18
    the indicated brackets on the Squat Slider (38) with a 3/8" x 3 1/4" Bolt (96) and a 3/8" Nylon Jamnut (113). Make sure that the Cable Trap is turned to hold the Cable in the groove of the Pulley. 86 90 72 90 59 2 90 59 73 86 90 120 68 124 78 124 96 73 113 38 18
  • Weider Pro 4850 | Canadian English Manual - Page 19
    Screw the end of the Cable (73) two full turns into the Weight Tube. Then, tighten the Nut against the 1/2" Washer (1). Remove the Weight Pin and set the Top Weight back on the weight stack. Replace the Pin. SEAT ASSEMBLY 56. Locate and open the parts bag labeled "SEAT ASSEMBLY." Insert the Pad Tube
  • Weider Pro 4850 | Canadian English Manual - Page 20
    (87). Do not tighten the Nylon Locknuts yet. Finish attaching the Squat Arm (32) to the Squat Bracket (37) with two 3/8" x 3" Carriage Bolts (126), a Small Support Plate (127), and two 3/8" Nylon Locknuts (87). Tighten all of the 3/8" Nylon Locknuts (87) used in this step. 59 20 32 51 20 108 51
  • Weider Pro 4850 | Canadian English Manual - Page 21
    move smoothly over the pulleys. If one of the cables does not move smoothly, find and correct the problem. IMPORTANT: If the cables are not properly installed, they may be damaged when heavy weight is used. See the CABLE DIAGRAMS on page 26 and 27 of this manual for proper cable routing. If there is
  • Weider Pro 4850 | Canadian English Manual - Page 22
    ADJUSTMENTS The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for various exercises. IMPORTANT: When attaching the lat bar, row bar, or handle, make sure that the
  • Weider Pro 4850 | Canadian English Manual - Page 23
    ADJUSTING THE SQUAT ARM OR SWIVEL CARRIAGE To adjust the height of the Squat Arm (32), first turn the Adjustment Knob (115) on the Squat Bracket (37) counterclockwise several turns to loosen it. Next, pull the Handle and slide the Squat Bracket up or down to the desired position. Engage the Handle
  • Weider Pro 4850 | Canadian English Manual - Page 24
    the resistance for each butterfly arm. Note: The actual resistance at each weight station may vary due to differences in individual weight plates as well as friction between the cables, pulleys, and weight guides. WEIGHT Top 1 2 3 4 5 6 7 8 9 10 HIGH PULLEY (lbs.) 14 25 38 48 61 68 80 96 101 112
  • Weider Pro 4850 | Canadian English Manual - Page 25
    TROUBLESHOOTING Make sure all parts are properly tightened each time the weight system is used. Replace any worn parts immediately. The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type of cable used on
  • Weider Pro 4850 | Canadian English Manual - Page 26
    in the diagrams show the routes of the cables. Use the diagrams to make sure that the cables have been assembled correctly. IMPORTANT: If the cables have not been correctly routed, the weight system will not function properly and damage may occur. Cable Identification Chart Butterfly Cable (69)-52
  • Weider Pro 4850 | Canadian English Manual - Page 27
    Leg Lever Cable (75) 3 4 2 1 Swivel Low Cable (72) 3 6 1 2 8 5 4 7 9 Swivel Cable (17) 1 3 5 2 4 27
  • Weider Pro 4850 | Canadian English Manual - Page 28
    IDENTIFICATION CHART-Model No. 831.153933 R1003A 1/2" Washer (1) 3/8" Washer (91) 5/16" Washer (90) 1/4" Washer (97) 1/2" Spacer (89) 3/4" Spacer (124) 1/2" Nut (118) 3/8" Nylon Locknut (87) 3/8" Nylon Jamnut (113) 5/16" Nylon Locknut (86) 1/4" Nylon Locknut (34) Cable Clip (83) 4 1/2" Pulley
  • Weider Pro 4850 | Canadian English Manual - Page 29
    1/4" x 3 1/2" Bolt (128) 3/8" x 2 1/2" Carriage Bolt (106) 1/4" x 1 1/2" Bolt (99) 3/8" x 2" Bolt (100) 3/8" x 1 3/4" Bolt (93) 5/16" x 1" Shoulder Bolt (103) 3/8" x 1" Bolt (13) #10 x 1" Screw (14) 5/16" x 3/4" Button Head Screw (51) 1/4" x 3/4" Screw (114) #8 x 3/4" Screw (98) 5/16" x 2 1/2"
  • Weider Pro 4850 | Canadian English Manual - Page 30
    1" Round Inner Cap (29) 1 1/2" x 2" Inner Cap (21) 2" x 2 1/2" Inner Cap (125) 2" Square Inner Cap (105) 1 1/2" Square Inner Cap (67) 2" x 3" Inner Cap (58)
  • Weider Pro 4850 | Canadian English Manual - Page 31
    Curl Knob 1/2" Nut 4 1/2" Pulley Long Base Large Cable Trap 3/8" x 3 3/4" Bolt Knee Rest Bumper 3/4" Spacer 2" x 2 1/2" Inner Cap 3/8" x 3" Carriage Bolt Small Support Plate 1/4" x 3 1/2" Bolt User's Manual Exercise Guide Note: "#" indicates a non-illustrated part. Specifications are subject to
  • Weider Pro 4850 | Canadian English Manual - Page 32
    EXPLODED DRAWING-Model No. 831.153933 26 51 103 100 69 60 113 51 29 60 70 86 100 86 21 113 70 25 69 103 54 108 28 27 29 51 51 28 54 92 90 86 78 86 89 87 91 58 89 86 125 87 104 91 57 47 91 101 88 107 104 91 98 57 18 102 56 57 55 91 59 90 58 58 78 31 92 18 113 85 90 68
  • Weider Pro 4850 | Canadian English Manual - Page 33
    in material or workmanship in this WEIGHT SYSTEM EXERCISER, contact the nearest Sears Service Center throughout the United States and Sears will repair or replace the WEIGHT SYSTEM EXERCISER, free of charge. This warranty does not apply when the WEIGHT SYSTEM EXERCISER is used commercially or for
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manu-
al for future reference.
WEIGHT SYSTEM EXERCISER
User’s Manual
Patent Pending
Model No. 831.153933
Serial No.
Write the serial number in the
space above for reference.
Serial Number Decal (under seat)
Sears, Roebuck and Co., Hoffman Estates, IL 60179
· Assembly
· Adjustments
· Troubleshooting
· Part List and Drawing