Weider Pro 9600 English Manual
Weider Pro 9600 Manual
 |
View all Weider Pro 9600 manuals
Add to My Manuals
Save this manual to your list of manuals |
Weider Pro 9600 manual content summary:
- Weider Pro 9600 | English Manual - Page 1
, or if there are missing parts, we will guarantee complete satisfaction free of charge. CUSTOMER HOT LINE: 1-800-999-3756 Mon.-Fri., 6 a.m.-6 p.m. MST CAUTION Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. USER'S MANUAL - Weider Pro 9600 | English Manual - Page 2
BEGIN 4 ASSEMBLY 5 ADJUSTMENTS 21 WEIGHT RESISTANCE CHART 23 TROUBLESHOOTING AND MAINTENANCE 24 CABLE DIAGRAMS 25 ORDERING REPLACEMENT PARTS Back Cover Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of this manual. Remove the PART IDENTIFICATION - Weider Pro 9600 | English Manual - Page 3
before using the weight system. 1. Read all instructions in this manual and in the accompanying literature before using the weight system. Use the weight system only as described in the literature. 2. It is the responsibility of the owner to ensure that all users of the weight system are adequately - Weider Pro 9600 | English Manual - Page 4
the weight system (see the front cover of this manual). Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled. High Pulley Station Lat Bar WARNING DECAL Ab Pulley Station Press Arms Seat Leg Press Weight Stack ASSEMBLED DIMENSIONS: Height - Weider Pro 9600 | English Manual - Page 5
assemble the weight system, make sure that all parts are oriented exactly as shown in the drawings. Tightening Parts Tighten all parts as you assemble them, unless instructed to do otherwise. Questions? If you have questions after reading the assembly instructions, please call our Customer Service - Weider Pro 9600 | English Manual - Page 6
on page 5. This brief introduction will save you much more time than it takes to read it. Locate and open the parts bags labeled "FRAME ASSEMBLY." See the inset drawing. Insert two 1 1/2" x 2 1/2" Inner Caps (83) and two 3/8" x 2" Carriage Bolts (92) into the Butterfly Base (4). Insert two - Weider Pro 9600 | English Manual - Page 7
Caps (83) into the ends of the Butterfly Top Frame (33). Attach the Butterfly Top Frame (33) to the Butterfly Upright (1) with two 3/8" x 2 1/2" Bolts (87), a Support Plate (94), and two 3/8" Nylon Locknuts (50). Do not tighten the Nylon Locknuts yet. 7 50 7 50 48 62 48 50 20 50 2 48 62 48 - Weider Pro 9600 | English Manual - Page 8
Press Top Frame (9). Attach the Press Top Frame (9) and a Support Plate (94) to the Press Upright (2) with two 3/8" x 2 1/2" Bolts (87) and two 3/8" Nylon Locknuts (50). Do not tighten the Nylon Locknuts yet. Note: Be sure that the Weight Guides (15) are properly positioned in relation to the Press - Weider Pro 9600 | English Manual - Page 9
33 13. Secure the Weight Guides (15) to the Press Top Frame (9) with two 3/8" x 1 3/4" Bolts (57) and two 13 3/8" Nylon Locknuts (50). Tighten the Nylon Locknuts used in steps 2-13. 57 9 50 50 15 ARM ASSEMBLY 14 14. Locate and open the parts bag labeled "ARM ASSEMBLY - Weider Pro 9600 | English Manual - Page 10
15. Insert a 2" Square Inner Cap (28) into the end of the Butterfly Arm (10). Attach a Butterfly Handle (53) to the Butterfly Arm (10) with two 3/8" x 1" Bolts (84) and two 3/8" Flat Washers (48). Repeat this step with the other Butterfly Arm (10). 16. Lubricate a 3/8" x 3 1/4" Bolt (62). Attach the - Weider Pro 9600 | English Manual - Page 11
must be able to turn freely. Refer to the Cable ID Chart on page 26 for help identifying the cables. Locate and open the parts bags labeled "CABLE ASSEMBLY" and "PULLEYS." Locate the Butterfly Cable (73), which is the shorter cable of the two that have eyelets on both ends. Attach the - Weider Pro 9600 | English Manual - Page 12
23. Remove the preassembled 3/8" x 2" Bolts (54) from one set of Adjustable Pulley Plates (23). 23 Wrap the Butterfly Cable (73) around a 3 1/2" Pulley (24). Attach the 3 1/2" Pulley and a Cable Trap (25) between the top holes of the Adjustable Pulley Plates (23) with a 3/8" x 2" Bolt (54) and a - Weider Pro 9600 | English Manual - Page 13
27. Wrap the Ab Cable (47) around a 3 1/2" Pulley (24). 27 Insert the Ab Cable down through the Press Top Frame (9). Attach a 3/8" Flat Washer (48) and a 5/8" x 3/4" Bushing (66) to a 3/8" x 3 1/4" Bolt (62). 24 62 Slide the Bolt through the Press Top Frame and the 3 1/2" Pulley. Secure - Weider Pro 9600 | English Manual - Page 14
Pulley. Secure another 5/8" x 3/4" Bushing and 3/8" Flat Washer to the Bolt with a 3/8" Nylon Locknut (50). 50 48 62 48 24 72 66 33. Insert the Weight Cable (72) through the hole in the Leg Lever (41), up around a 3 1/2" Pulley (24), back through the hole in the Leg Lever, and through the - Weider Pro 9600 | English Manual - Page 15
the Cable Trap is turned to hold the Cable in place. 24 25 57 38. Note: For convenience, the weights assembled 38 in step 9 are not shown in the following draw- ings. Wrap the Weight Cable (72) around a 3 1/2" Pulley (24). Attach the 3 1/2" Pulley and a Cable Trap (25) to the bracket on the - Weider Pro 9600 | English Manual - Page 16
the 3 1/2" Pulley between two Small Pulley Plates (22) with a 3/8" x 1 3/4" Bolt (57) and a 3/8" Nylon Locknut (50). 24 50 72 57 22 41. Wrap the Weight Cable (72) around a 4 1/2" Pulley 41 (82). Attach the 4 1/2" Pulley to the bracket on the Press Top Frame (9) with a 3/8" x 2" Bolt (54) and - Weider Pro 9600 | English Manual - Page 17
43. Locate the Leg Press Cable (75). Attach the Leg Press Cable to the indicated side of the Press Upright (2) with a 3/8" x 3 1/4" Bolt (62) and a 3/8" Nylon Locknut (50). Do not tighten the Nylon Locknut yet. Wrap the Leg Press Cable (75) up around a 3 1/2" Pulley (24) in the direction shown. - Weider Pro 9600 | English Manual - Page 18
47. Remove the 3/8" Nylon Locknut (50) from the indi- 47 cated 3/8" x 5 1/2" Bolt (55). Wrap the Leg Press Cable (75) around a 3 1/2" Pulley (24). Secure the 3 1/2" Pulley and a Cable Trap (25) to the 3/8" x 5 1/2" Bolt (55) on the indicated side of the Press Base (6) with the 3/8" Nylon Locknut - Weider Pro 9600 | English Manual - Page 19
51 51. Locate and open the parts bag labeled "SEAT ASSEMBLY." Attach a Seat (13) to the brackets on the Butterfly Seat Frame (14) using four 1/4" x 3/4" Bolts (49). Repeat this step with the other Seat (not shown) - Weider Pro 9600 | English Manual - Page 20
the remaining parts will be explained in ADJUSTMENTS, beginning on page 21 of this manual. Before using the weight system, pull each cable a few times to be sure that the cables move smoothly over the pulleys. If one of the cables does not move smoothly, find and correct the problem. IMPORTANT: If - Weider Pro 9600 | English Manual - Page 21
ADJUSTMENTS The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for each exercise. IMPORTANT: When attaching the lat bar, ab strap, or nylon strap, make sure that the - Weider Pro 9600 | English Manual - Page 22
in the Preacher Post. Turn the Large Adjustment Knob clockwise until tight. Note: When not using the Curl Pad (91), store it away from the weight system. 47 69 81 2 12 5 91 46 39 3 22 - Weider Pro 9600 | English Manual - Page 23
listed is the resistance for each butterfly arm. Note: The actual resistance at each weight station may vary due to differences in individual weight plates, as well as friction between the cables, pulleys, and weight guides. WEIGHT PLATES Top 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 PRESS - Weider Pro 9600 | English Manual - Page 24
TROUBLESHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the weight system. Replace any worn parts immediately. The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type of cable used - Weider Pro 9600 | English Manual - Page 25
to be sure that the Cables have been assembled correctly. The starting and ending points of each Cable have been labeled. The numbers show the proper route for each Cable. IMPORTANT: If the Cables have not been correctly routed, the weight system will not function properly and damage may occur - Weider Pro 9600 | English Manual - Page 26
Weight Cable (72) 11 Cable ID 9 10 6 12-Weight Stack 8 7 5 4 2 72 47 75 73 3 1-Low Pulley 26 - Weider Pro 9600 | English Manual - Page 27
NOTES 27 - Weider Pro 9600 | English Manual - Page 28
ORDERING REPLACEMENT PARTS To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, WEIDER® 9600 PRO weight system) 3. The SERIAL NUMBER of the product (see the front cover of this manual) 4. The KEY NUMBER and DESCRIPTION of the part(s) (see the PART - Weider Pro 9600 | English Manual - Page 29
to the key number of the part from the PART LIST in the center of this manual. Important: Some parts may have been pre-assembled for shipping purposes. If you cannot find a part in the parts bags, check to see if it has been pre-assembled. Note: The assembly procedure is divided into four stages - Weider Pro 9600 | English Manual - Page 30
PART IDENTIFICATION CHART-Model No. WESY59101 R0103A 1/2" Flat Washer (11) 3/8" Flat Washer (48) Cable Clip (69) 1/2" Plain Nut (100) 1/2" Nylon Jamnut (36) 3/8" Nylon Locknut (50) 5/16" - Weider Pro 9600 | English Manual - Page 31
3/8" x 2" Carriage Bolt (92) 3/8" x 2" Bolt (54) 3/8" x 1 3/4" Bolt (57) 3/8" x 1 1/4" Button Head Bolt (98) 3/8" x 1" Bolt (84) 1" Tap Screw (80) 1/4" x 3/4" Bolt (49) #8 x 1/2" Screw (45) 5/16" x 2 1/4" Shoulder Bolt (79) 3/8" x 2 1/2" Bolt (87) 5/16" x 2 3/4" Bolt (96) 3/8" x 2 3/4" Bolt (89) - Weider Pro 9600 | English Manual - Page 32
2" x 3" Inner Cap (78) 2 1/2" Square Inner Cap (76) 1 1/2" Square Inner Cap (35) 1 1/2" x 2 1/2" Inner Cap (83) 2" Square Inner Cap (28) - Weider Pro 9600 | English Manual - Page 33
REMOVE THIS PART LIST/EXPLODED DRAWING FROM THE MANUAL. SAVE THIS PART LIST/EXPLODED DRAWING FOR FUTURE REFERENCE 81 - Weider Pro 9600 | English Manual - Page 34
2" Carriage Bolt Workout Decal Support Plate Plastic Weight Cover 5/16" x 2 3/4" Bolt 1/2" x 3/4" Spacer 3/8" x 1 1/4" Button Head Bolt 5/8" x 1/2" Spacer 1/2" Plain Nut 5/16" Nylon Jamnut User's Manual Exercise Guide Note: "#" indicates a non-illustrated part. Specifications are subject to change - Weider Pro 9600 | English Manual - Page 35
91 49 49 39 49 28 12 86 25 54 24 23 25 24 23 49 35 44 49 62 87 50 66 62 24 48 48 83 50 50 47 62 48 47 66 24 66 82 54 50 48 48 50 50 61 94 9 54 50 66 24 50 66 48 65 24 50 45 72 57 100 11 50 65 77 65 13 28 2 50 17 93 5 15 60 24 96 68 68 29 64 25 77
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
 |
 |
USER'S MANUAL
QUESTIONS?
As a manufacturer, we are
committed to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, we will guarantee
complete satisfaction through
assistance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR
TOLL-FREE CUSTOMER
HOT LINE. The techni-
cians on our customer
hot line will provide
immediate assistance,
free of charge.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
Model No. WESY59101
Serial No.
Write the serial number in the space
above for future reference.
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
www.weiderfitness.com
new products, prizes,
fitness tips, and much more!
Serial Number Decal (Under Seat)