Whirlpool LEV4634JQ Installation Instructions
Whirlpool LEV4634JQ Manual
 |
View all Whirlpool LEV4634JQ manuals
Add to My Manuals
Save this manual to your list of manuals |
Whirlpool LEV4634JQ manual content summary:
- Whirlpool LEV4634JQ | Installation Instructions - Page 1
? Check your Use and Care Guide for a toll-free number to call, or call your dealer. The dealer is listed in the Yellow Pages of your phone directory under "Appliances -- Household -- Major -- Service and Repair." When you call, you will need the dryer model number and serial number - Whirlpool LEV4634JQ | Installation Instructions - Page 2
inch. (If slope is greater than I inch, install Extended Dryer Feet Kit, Part No. 279810.) Clothes may not tumble properly and automatic sensor cycles may not operate correctly if dryer is not level. I/Sturdy floor to support dryer weight of 175 pounds. 1 inch It is yourresponsibilityto: I/Observe - Whirlpool LEV4634JQ | Installation Instructions - Page 3
there instructions can supported when the dryer Service check: Back pressure in any exhaust system used must not exceed 0.6 inches in water column measured with an incline manometer at the point that exhaust vent connects to dryer. Mobile home installation requirements If codes permit, this appliance - Whirlpool LEV4634JQ | Installation Instructions - Page 4
around exhaust hood. m Connect exhaust vent to hood• (Exhaust vent MUST fit inside hood•) Secure vent to hood with clamp• m Run exhaust vent to dryer location. Use the straightest path possible. (See Panel B.) Use clamps to seal all joints. Excessive Weight Hazard Use two or more people to move - Whirlpool LEV4634JQ | Installation Instructions - Page 5
wire This dryer is manufactured with the cabinet-ground conductor connected to the NEUTRAL (center) of the wiring harness at the terminal block, if local codes do NOT permit this type of connection, use "Four-wire connection" instructions• GROUNDING INSTRUCTIONS_ This appliance must be grounded - Whirlpool LEV4634JQ | Installation Instructions - Page 6
strain relief screws. 8. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold down screw. wire reenter) Where 5, Remove the appliance harness ground wire (green with yellow stripes) from the external ground connector screw. Connect appliance harness ground wire - Whirlpool LEV4634JQ | Installation Instructions - Page 7
. m Lift door until top screws in cabinet are in large part of hinge slot. Pull door forward off screws• Set door (handle side up) on top of dryer• Remove top screws from cabinet• Complete door swing change following the instructions for your type door. • Carefully remove 4 hinge hole plugs (C) on - Whirlpool LEV4634JQ | Installation Instructions - Page 8
on. 11 Check that you: If did not skip any steps. installed all parts. I/propedy installed dryer legs. 11/ leveled dryer. _ i- lJ have all the tools you started with. ' m Read the Use and Care Guide to fully understand your new dryer. Select a full heat cycle (not the air cycle) and start - Whirlpool LEV4634JQ | Installation Instructions - Page 9
safety message in this manual and on your appliance. Nways read and obey and tell you what can happen if the instructions are not followed. Check that you have power supply cable. Part No. 3978844 © 2000 Whirlpool Corporation Electrical If using a power supply cord: Dryer power supply cord must
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
 |
 |
Havequestionsaboutyourdryer?
Check your
Use
and Care Guide for a toll-free
number
to
call,
or call
your
dealer. The dealer is
listed
in the Yellow Pages of your
phone directory
under
"Appliances
--
Household --
Major
--
Service and Repair."
When you call, you will
need the dryer
model
number
and serial number.
Both numbers
are on the model/serial
rating
plate located
in the door well
behind
the dryer door
and on front
of opening.
Record
the numbers
here
for
handy
reference:
Model
No,
_
__
_J,/_'/'/_
Serial
No
Movingdryertoanew
Iocatzon?
Check with
a licensed electrician
to confirm
that supply voltage
at new
home
matches voltage
specified on the model/serial
rating
plate.
Shut off
electrical
supply to dryer. Unplug
power supply cord and tape it securelyto dryer.
(Or
disconnectpower supplycable from dryer.)
\
door to
panel.
ElectricDryer
Pa_
No.
3978844
Slide dryer
onto cardboard
or hardboard
before
moving
it across
the
floor
to
prevent
damaging
floor
covering.
leveling
legs
all
the
way in.
IMPORTANT:
Readandsavetheseinstructions.
Installer:
Leave
installation Instructions
with
homeowner.
Homeowner:
Keep Installation
instructions
for future
reference.
For best performance,
install
dryer according
to
Installation
Instructions.
Failure
to complete
installation
as instructed
could void warranty.
Save
Installation
Instructions
for local electrical
inspector's
use.