Home » Whirlpool Manuals » Laundry Dryers » Whirlpool LTE5243DQ » Manual Viewer

Whirlpool LTE5243DQ Ventilation Specification

Whirlpool LTE5243DQ - Stack Washer Electric Dryer Manual

UPC - 050946532578

View all Whirlpool LTE5243DQ manuals

Add to My Manuals
Save this manual to your list of manuals

Whirlpool LTE5243DQ manual content summary:

Whirlpool LTE5243DQ | Ventilation Specification - Page 1
, and tell you what can happen if the instructions are not followed. ■ If you are installing a gas dryer, it is recommended that the owner post, in a prominent location, instructions for the customer's use in the event the customer smells gas. This information should be obtained from your local
Whirlpool LTE5243DQ | Ventilation Specification - Page 2
the information in this manual must be followed to gas supplier, call the fire department. - Installation and service must be performed by a qualified installer, service agency, or the gas supplier. In the State of Massachusetts, the following installation instructions apply: ■ Installations
Whirlpool LTE5243DQ | Ventilation Specification - Page 3
Do not install or store the dryer where it will be exposed to the weather. ■ Do not tamper with controls. ■ Do not repair or replace any part of the dryer or attempt any servicing unless specifically recommended in this Use and Care Guide or in published user-repair instructions that you understand
Whirlpool LTE5243DQ | Ventilation Specification - Page 4
.5.1 - Gas Clothes Dryers. 5. Other sections of these codes may also apply to multi-dryer vent systems. There are other codes requiring dryers to be exhausted when installed in confined spaces where specified clearances from combustible surfaces cannot be met. See the Installation Instructions that
Whirlpool LTE5243DQ | Ventilation Specification - Page 5
90° bends, and the installation requires three 90° bends, the total allowable vent length would be reduced by 10 ft (3.0 m) (from 40 ft [12.2 m] to 30 ft [9.1 m]). Dryer Airflow The airflow of a dryer depends on the design of the exhaust vent. Each dryer model has a maximum rated vent length, shown
Whirlpool LTE5243DQ | Ventilation Specification - Page 6
of a generic horizontal system. Option 3 - Combination System The combination system may be used in high-rise apartments, with a bank of dryers installed at several different levels. Each of these banks then exhausts into a central vertical vent. See the following illustration for an example of
Whirlpool LTE5243DQ | Ventilation Specification - Page 7
flappers or louvers (if installed as part of the exhaust system) will not open or close completely. ■ After cleaning the exhaust hood, check that the flapper or louvers move freely. 3. Reassemble the exhaust duct and hood, checking that the joints are secure. 4. Operate the dryer and verify that the
Whirlpool LTE5243DQ | Ventilation Specification - Page 8
W10200920C © 2008. Whirlpool Corporation. All rights reserved. ® Registered Trademark/TM Trademark of Whirlpool, U.S.A. 8/08 Printed in U.S.A.

Section	Page
dryer venting specifications	1
Table of Contents	1
dryer Safety	1
Post the following warning in a prominent location.	1
installation requirements	4
WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS.	4
NOTE: This guide is intended to aid licensed HVAC or Architectural Engineers who design single and multi-dryer unit venting systems for Whirlpool Corporation dryers sold in the United States. Whirlpool Corporation provides required airflow and back p...	4
Outside Exhaust	4
The four basic reasons for exhausting a dryer outdoors are detailed in this section:	4
1. To meet codes requirements.	4
2. To remove moisture from laundry area.	4
3. To avoid lint accumulation in laundry area.	4
4. To remove excess heat from laundry area.	4
Codes Requirements	4
The following codes should be reviewed to ensure dryer vent systems are in compliance:	4
1. International Mechanical Code: In the 2000 version, sections 504 and 913.	4
2. International Fuel Gas Code: In the 2003 version, section 614.	4
3. UL 2158 Electric Clothes Dryer Standard references venting requirements in paragraph 7.3.	4
4. ANSI Z21.5.1 - Gas Clothes Dryers.	4
5. Other sections of these codes may also apply to multi-dryer vent systems.	4
There are other codes requiring dryers to be exhausted when installed in confined spaces where specified clearances from combustible surfaces cannot be met. See the Installation Instructions that came with your dryer for spacing requirements.	4
Local codes and ordinances that exist must also be met. Consult your local building inspector for more information.	4
Moisture	4
A normal towel load contains some residual water when it is removed from the washer. The dryer must remove this water and discharge it from the drum. When the dryer is not exhausted outside, this moist air will be recirculated through the heating sou...	4
Exhausting moisture into the room can also cause damage to walls, floors, picture hangers, and cause condensation on windows and walls in cold weather.	4
Lint	4
Even though the dryer is equipped with a lint screen, fine particles of lint can get through the screen and be exhausted out of the dryer. Proper venting of the dryer will keep lint from accumulating in the laundry area.	4
Heat	4
In order to remove moisture from the garments in the dryer, heat is generated to vaporize the water. Exhausting the dryer outdoors removes excess heat from the laundry area of the building.	4
Central Exhaust System Requirements	4
The following guidelines should be considered in the design of any central exhaust system:	4
Venting Requirements	5
Venting systems for Whirlpool dryers must meet the following requirements:	5
Back pressure should be measured with an empty dryer, a clean lint screen and with the dryer operating in the Air Only cycle (no heat). Use an inclined manometer, such as Dryer model 102 (0\	5
Single Dryer Venting Systems	5
Single dryer venting systems are defined as systems that have only one dryer unit attached to a residential-type 4\	5
In cases in which the Installation Instructions do not address the vent length for the specific number of elbows required for a particular application, the following calculations may be used. (The total vent system length includes all straight and cu...	5
For example, if the Installation Instructions state that a dryer is allowed 40 ft (12.2 m) of total vent length with two 90° bends, and the installation requires three 90° bends, the total allowable vent length would be reduced by 10 ft (3.0 m) (fr...	5
The airflow of a dryer depends on the design of the exhaust vent. Each dryer model has a maximum rated vent length, shown in the product literature that is supplied with each model, or on the Whirlpool.com website. The exhaust airflow of any Whirlpoo...	5
All Whirlpool electric dryer models, including “long vent dryers,” that are sold in the United States and Canada are UL listed (reference UL2158 standard), and all Whirlpool gas dryer models are CSA listed (reference ANSI Z21.5.1 standard). These...	5
Closets used for dryer installation must provide multiple openings to allow air to flow through the dryer and around the dryer to dissipate heat. Refer to the product literature for details of room venting requirements. Any dryer enclosure or room th...	5
“AF” Code	5
Certain electronic dryer models have airflow detection capabilities. (See specific model product literature for details). If the airflow in the dryer is extremely low, an “AF” code will be displayed on the control panel. For single dryer venting ...	5
For multi-dryer venting systems, the “AF” code means that your vent may be blocked or partially blocked or that the venting system is creating back pressure in excess of the maximum allowable 0.6\	5
Multiple Dryer Venting Systems	5
Multiple dryer venting systems must be designed specifically for each application.	5
NOTE: It is recommended that an architectural or HVAC engineering firm be consulted for designing the dryer venting system.	5
Connecting a number of dryers to a single vent system is common in coin-laundry stores and in many apartment buildings. Listed here are some requirements for examples of three different multiple dryer venting systems.	5
The most common is the horizontal system, in which banks of dryers are all located in one room and vented through a common duct. See the following illustration for an example of a generic horizontal system.	6
The vertical system is used in some apartment buildings that have a washer and dryer on each floor. Each dryer is exhausted into the same central vertical duct. See the following illustration for an example of a generic vertical system.	6
The combination system may be used in high-rise apartments, with a bank of dryers installed at several different levels. Each of these banks then exhausts into a central vertical vent. See the following illustration for an example of a combination sy...	6
Dryer inspection and cleaning	7
Frequency of Exhaust System Cleaning	7
Every exhaust system must be inspected periodically and cleaned to ensure that it is intact and free from lint accumulation. The frequency of these inspections will vary, depending on the system and usage of the dryer. For single-family usage, an ann...	7
Inspecting the Exhaust System	7
1. Disconnect the exhaust duct from the dryer and from the exhaust hood (at the exhaust outlet).	7
2. Inspect the interior of the duct and remove any lint accumulation.	7
3. Reassemble the exhaust duct and hood, checking that the joints are secure.	7

Match case Limit results 1 per page

DRYER VENTING SPECIFICATIONS

W10100920C

Table of Contents

DRYER VENTING SPECIFICATIONS

..................................................................................................

DRYER SAFETY

....................................................................................................................................

INSTALLATION REQUIREMENTS

......................................................................................................

Venting Requirements

.......................................................................................................................

DRYER INSPECTION AND CLEANING

..............................................................................................

Frequency of Exhaust System Cleaning

...........................................................................................

Inspecting the Exhaust System

.........................................................................................................

You

You can be killed or seriously injured if you don't immediately

can be killed or seriously injured if you don't

All

afety me

age

will tell you what the potential hazard i

, tell you how to reduce the chance of injury, and tell you what can

happen if the in

truction

are not followed.

Your safety and the safety of others are very important.

We have provided many important

afety me

age

in thi

manual and on your appliance. Alway

read and obey all

afety

age

Thi

the

afety alert

ymbol.

Thi

ymbol alert

you to potential hazard

that can kill or hurt you and other

All

afety me

age

will follow the

afety alert

ymbol and either the word “DANGER” or “WARNING.”

The

e word

mean:

follow instructions.

instructions.

DANGER

WARNING

DRYER SAFETY

■

If you are installing a gas dryer, it is recommended that the owner post, in a prominent location, instructions for the customer’s use in

the event the customer smells gas. This information should be obtained from your local gas supplier.

Post the following warning in a prominent location.

FOR YOUR

AFETY

Do not

tore or u

e ga

oline or other ﬂammable vapor

and li

uid

in the vicinity of thi

or any other appliance.