Whirlpool MH1160XSQ Installation Instructions
Whirlpool MH1160XSQ Manual
 |
View all Whirlpool MH1160XSQ manuals
Add to My Manuals
Save this manual to your list of manuals |
Whirlpool MH1160XSQ manual content summary:
- Whirlpool MH1160XSQ | Installation Instructions - Page 1
Holes in Rear Wall 7 Attach Mounting Plate to Wall 8 Prepare Upper Cabinet 8 Install Damper Assembly 9 Install the Microwave Oven 9 Complete Installation 10 VENTING DESIGN SPECIFICATIONS 11 ASSISTANCE 12 Replacement Parts 12 Accessories 12 MICROWAVE HOOD COMBINATION SAFETY Your safety and - Whirlpool MH1160XSQ | Installation Instructions - Page 2
template Mounting plate (attached to back of microwave oven) Cardboard template (part of packaging) Aluminum grease filters Charcoal filters (Depending on model, charcoal filters may not be included. See Use and Care Guide.) NOTE: Depending on model, aluminum grease filter and charcoal filter may - Whirlpool MH1160XSQ | Installation Instructions - Page 3
for 66" (167.6 cm) installation height. Exact dimensions may vary depending on type of range/cooktop below. Product Dimensions 17¹⁄₄" (43.8 cm) 16¹⁄₄" (41.3 cm) (401.05³c⁄₄m") 29⁷⁄₈" (76.0 cm) GROUNDING INSTRUCTIONS ■ For all cord connected appliances: The microwave oven must be grounded. In - Whirlpool MH1160XSQ | Installation Instructions - Page 4
INSTALLATION INSTRUCTIONS Remove Mounting Plate NOTE: To avoid possible damage to the work surface, cover the work surface. 1. Remove any remaining contents from the microwave oven cavity. 2. Remove the mounting plate and set aside. Rotate Blower Motor The microwave oven is set for recirculation - Whirlpool MH1160XSQ | Installation Instructions - Page 5
motor is not positioned with flat sides facing the back of the microwave oven (as shown), performance will be poor. 6. Reattach blower motor to back of microwave oven with 2 screws removed in Step 3 of "Wall Venting Installation Only." Securely tighten screws. NOTE: If blower motor is not correctly - Whirlpool MH1160XSQ | Installation Instructions - Page 6
venting installation can be done. Wall Stud at One End Hole Figure 3 Wall Studs at Both End Holes Figure 4 B D B A A,D A,D A,D E E E E C C C C F F A. End holes (on mounting plate) B. Cabinet opening vertical centerline C. Wall stud centerlines D. Holes for lag screws E. Support - Whirlpool MH1160XSQ | Installation Instructions - Page 7
Wall The microwave oven must be installed on a 5. With the support tabs facing forward (see illustrations in "Locate Wall Stud(s)" section, align the mounting plate center markers in Rear Wall In addition to being installed on at least 1 wall stud, the mounting plate must attach to the wall at both - Whirlpool MH1160XSQ | Installation Instructions - Page 8
support tabs of the mounting plate facing forward, insert a 1/4-20 x 3" round-head bolt through the end hole that fits over the 3/4" (19 mm) hole drilled in Step 3 of "Installation the top of the microwave oven. NOTE: If The template has trim lines to use as guides. 4. Make sure the 10" (25.4 cm - Whirlpool MH1160XSQ | Installation Instructions - Page 9
needs to be installed around the supply microwave oven door is closed and taped shut. 3. Using 2 or more people, lift microwave oven and hang it on support tabs at the bottom of mounting plate. NOTE: To avoid damage to the microwave oven, do not grip or use the door or door handle while the microwave - Whirlpool MH1160XSQ | Installation Instructions - Page 10
the fuse or reset the circuit breaker. If the problem continues, call an electrician. ■ Check that the power supply cord is plugged into a grounded 3 prong outlet. ■ See the Use and Care Guide for troubleshooting information. Installation is now complete. Save Installation Instructions for future - Whirlpool MH1160XSQ | Installation Instructions - Page 11
VENTING DESIGN SPECIFICATIONS This section is intended for architectural designer and builder/contractor reference only. NOTES: ■ Vent materials needed for installation are not provided with microwave hood. Rectangular to Round Transition NOTE: The minimum 3" (7.6 cm) clearance must exist between - Whirlpool MH1160XSQ | Installation Instructions - Page 12
installation hardware needs to be replaced, call us at our toll free number listed in the User Instructions. Following is a list of available replacement parts. You will need your model number located on the front facing of the microwave oven opening, behind the door. ■ Damper Assembly ■ Mounting
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
 |
 |
MICROWAVE HOOD COMBINATION
INSTALLATION INSTRUCTIONS
MICROWAVE HOOD COMBINATION SAFETY
This product is suitable for use above electric or gas cooking products up to and including 36" (91.4 cm) wide. See “Installation
Requirements” section for further notes.
These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration in
these installation instructions.
Table of Contents
MICROWAVE HOOD COMBINATION SAFETY
..............................
1
INSTALLATION REQUIREMENTS
...................................................
2
Tools and Parts
...............................................................................
2
Remove Cardboard Template
........................................................
2
Location Requirements
...................................................................
2
Product Dimensions
.......................................................................
3
Electrical Requirements
..................................................................
3
INSTALLATION INSTRUCTIONS
.....................................................
4
Remove Mounting Plate
.................................................................
4
Rotate Blower Motor
.......................................................................
4
Locate Wall Stud(s)
.........................................................................
6
Mark Rear Wall
................................................................................
7
Drill Holes in Rear Wall
....................................................................
7
Attach Mounting Plate to Wall
........................................................
8
Prepare Upper Cabinet
...................................................................
8
Install Damper Assembly
................................................................
9
Install the Microwave Oven
............................................................
9
Complete Installation
....................................................................
10
VENTING DESIGN SPECIFICATIONS
............................................
11
ASSISTANCE
...................................................................................
12
Replacement Parts
.......................................................................
12
Accessories
...................................................................................
12
W10191951A
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING