Whirlpool MH1170XSB Installation Instructions
Whirlpool MH1170XSB Manual
 |
View all Whirlpool MH1170XSB manuals
Add to My Manuals
Save this manual to your list of manuals |
Whirlpool MH1170XSB manual content summary:
- Whirlpool MH1170XSB | Installation Instructions - Page 1
the Microwave Oven 9.. Complete Installation 1. 0 VENTING DESIGN SPECIFICATIONS 11 ASSISTANCE 1.2 Replacement Par_s 1.2 Accessories 1.2 MICROWAVE HOOD COMBINATION SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and - Whirlpool MH1170XSB | Installation Instructions - Page 2
Care Guide.) NOTE: Depending on model, aluminum grease filter and charcoal filter may be combined. Materials needed • Standard fittings for wall or roof venting. See "Venting Design Specifications" section. Loccion I4!eq ,i emen'Is Check the opening where the microwave oven wll be installed. The - Whirlpool MH1170XSB | Installation Instructions - Page 3
) installation height. Exact dimensions may vary depending on type of range/cooktop below. 171/8`' (43.5 cm) IS If II IS ISIJ IJ I -I/ T 15%" i(40.3 cm) GROUNDING INSTRUCTIONS [] For all cord connected appliances: The microwave oven must be grounded. In the event of an electrical short circuit - Whirlpool MH1170XSB | Installation Instructions - Page 4
. Keep the damper assembly in case the venting method is changed, or the microwave oven is reinstalled in another location where wall or roof venting may be used. Wall Venting Installation Only 1. Remove screws attaching damper plate to top of microwave oven exterior. Side damper plate toward the - Whirlpool MH1170XSB | Installation Instructions - Page 5
face the back of microwave oven, and lower it back into the microwave oven. Roof Venting Installation Only 1. Repeat Step 1 from "Wall Venting Installation Only," 2. Repeat Step 2 from "Wall Venting Installation Only," 3. Repeat Step 3 from "Wall Venting Installation Only." 4. Repeat Step 4 from - Whirlpool MH1170XSB | Installation Instructions - Page 6
do not install the oven, See illustrations in "Possible Wall Stud Configurations," S ud(s} 1. Using a stud finder show examples of preferred installation configurations with the Mark Rear Wall" section), only recirculation or roof venting installation can be done. Wall Studs at All Four Corner - Whirlpool MH1170XSB | Installation Instructions - Page 7
The microwave oven must be installed on a minimum of I wall stud, preferably 2, using a minimum of 1 lag screw, preferably 2 or more. 1. Using measuring tape, find and clearly mark the vertical centerline of the opening. Wall Venting Installation Only Centerline Upper cabinet bottom t 4" (10.2 - Whirlpool MH1170XSB | Installation Instructions - Page 8
holes in the top of the microwave oven. NOTE: If the upper cabinet has a frame around it, trim the template edges so that it fits inside the frame, against the upper cabinet bottom. The template has trim lines to use as guides. 4. Make sure the 10" (25.4 cm) dimension from the rear wall to points - Whirlpool MH1170XSB | Installation Instructions - Page 9
of the microwave oven so that the damper blade opens away from the microwave oven. C 3. Using 2 or more people, lift microwave oven and hang it on support tabs at the bottom of mounting plate. NOTE: Do not grip or use the door or door handle during installation. A. Back of microwave oven B. Damper - Whirlpool MH1170XSB | Installation Instructions - Page 10
bottom and the microwave oven. A Connect vent to damper assembly. A B _ii ii ii A. Vent B. Damper assembly (under vent) C% om_ © e' te I _ _s' cs c$"_ on 1. Refer to the Use and Care Guide for instructions on how to install filters into your model. A. Bolts For Roof Venting Installation Only - Whirlpool MH1170XSB | Installation Instructions - Page 11
exist between the top of the microwave oven and the rectangular to round transition piece so that the damper can open freely and fully. For optimal venting installation, we recommend: • using roof or wall caps that have back draft dampers • using a rigid metal vent • using the most direct route by - Whirlpool MH1170XSB | Installation Instructions - Page 12
on the model and serial number plate, which is located behind the microwave oven door on the front frame of the microwave oven. If you need additional assistance, call us at our toll free number listed in the Use and Care Guide, or visit us on the Web. If any of the installation hardware needs
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
 |
 |
MICROWAVE
HOOD
COMBINATION
INSTALLATION INSTRUCTIONS
This product
is suitable for use above electric or gas cooking
products
up to 36" (91.4 cm) wide.
These installation
instructions
cover different
models. The appearance
of your particular model
may differ slightly
from the
illustration
in these installation
instructions.
NOTES:
•
Proper installation is the responsibility of the installer.
•
Product failure due to improper installation is not covered under the warranty.
Table of
Contents
MICROWAVE HOOD COMBINATION SAFETY
..............................
J
INSTALLATIONREQUIREMENTS
...................................................
2
Tools and Parts
...............................................................................
2
Location Requirements
...................................................................
2
Product Dimensions
.......................................................................
3
Electrical Requirements
..................................................................
3
INSTALLATIONINSTRUCTIONS
.....................................................
4
Remove Mounting Plate
.................................................................
4
Rotate Blower Motor
.......................................................................
4
Locate Wall Stud(s)
.........................................................................
6
Mark RearWall
................................................................................
7
Drill Holes in RearWall
....................................................................
7
Attach Mounting Plate to Wall
........................................................
8
Prepare Upper Cabinet
...................................................................
8
Install Damper Assembly
................................................................
9
Install the Microwave
Oven
............................................................
9
Complete Installation
...................................................................
10
VENTING DESIGN SPECIFICATIONS
...........................................
11
ASSISTANCE
..................................................................................
12
ReplacementPar_s
......................................................................
12
Accessories
..................................................................................
12
MICROWAVE HOOD COMBINATION
SAFETY
Your
safety
and
the
safety
of others
are very
important.
We have provided
many important
safety messages
in this manual and on your appliance.
Always
read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential
hazards that can kill or hurt you and others.
All safety messages
will follow the safety alert symbol and either the word "DANGER"
or "WARNING."
These words mean:
You can be killed or seriously
injured if you don't immediately
follow
instructions.
You can be killed or seriously
injured
if you don't
follow
instructions.
All safety messages
will tell you what the potential
hazard is, tell you how to reduce the chance
of injury, and tell you what can
happen
if the instructions
are not followed.
IMPORTANT:
Read Installation
Instructions
thoroughly
before beginning
installation.
Save Installation
Instructions
for local house
inspector's
use.
8206555