Whirlpool MMV4203DQ Installation Instructions
Whirlpool MMV4203DQ Manual
 |
View all Whirlpool MMV4203DQ manuals
Add to My Manuals
Save this manual to your list of manuals |
Whirlpool MMV4203DQ manual content summary:
- Whirlpool MMV4203DQ | Installation Instructions - Page 1
section for further notes. These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration in these installation instructions. Table of Contents MICROWAVE HOOD COMBINATION SAFETY 1 INSTALLATION REQUIREMENTS 2 Tools and Parts - Whirlpool MMV4203DQ | Installation Instructions - Page 2
: Upper cabinet template Mounting plate (attached to back of microwave oven) Aluminum grease filters Charcoal filters (Depending on model, charcoal filters may not be included. See User Instructions.) NOTE: Depending on model, aluminum grease filter and charcoal filter may be combined. Materials - Whirlpool MMV4203DQ | Installation Instructions - Page 3
if the grounding instructions are not completely understood, or if doubt exists as to whether the microwave oven is properly grounded. Do not use an extension cord. If the power supply cord is too short, have a qualified electrician or serviceman install an outlet near the microwave oven. SAVE THESE - Whirlpool MMV4203DQ | Installation Instructions - Page 4
INSTALLATION INSTRUCTIONS Remove Mounting Plate NOTE: To avoid possible damage to the work surface, cover the work surface. 1. Remove any remaining contents from the microwave oven cavity. 2. Remove the 2 screws that attach the mounting plate to the back of the microwave oven, then remove mounting - Whirlpool MMV4203DQ | Installation Instructions - Page 5
the top, and the blade opening away from the microwave oven. A 4. Close damper plate and secure it with screw removed in Step 1 of "Wall Venting Installation Only." A B B C D E F A. Damper assembly B. Lower locking tabs C. Guides D. Damper blade (open) E. Damper plate screw F. Blower motor screw - Whirlpool MMV4203DQ | Installation Instructions - Page 6
- Two Wall Studs A C C F D D Mark Rear Wall The microwave oven must be installed on a minimum of 1 wall stud, preferably 2, using a minimum of for toggle bolts C. Wall stud centerlines D. Holes for lag screws E. Support tabs F. Mounting plate center marker 14¹⁄₂" (36.8 cm) Centerline Top - Whirlpool MMV4203DQ | Installation Instructions - Page 7
venting cutout area. Drill Holes in Rear Wall In addition to being installed on at least 1 wall stud, the mounting plate must attach to lag screws. Refer to illustrations in "Locate Wall Stud(s)" section. 1. With the support tabs of the mounting plate facing forward, insert 3/16-20 x 3" hex-head - Whirlpool MMV4203DQ | Installation Instructions - Page 8
guides. 4. Make sure the 8³⁄₄" (22.2 cm) dimension from the rear wall to points "D," "E" and "H" on the template is maintained. Install the Microwave needs to be installed around the supply cord hole, as shown. B 3. Using 2 or more people, lift microwave oven and hang it on support tabs at the - Whirlpool MMV4203DQ | Installation Instructions - Page 9
the vent fan. 5. If the microwave oven does not operate: ■ problem continues, call an electrician. ■ Check that the power supply cord is plugged into a grounded 3 prong outlet. ■ See the User Instructions for troubleshooting information. Installation is now complete. Save Installation Instructions - Whirlpool MMV4203DQ | Installation Instructions - Page 10
SPECIFICATIONS This section is intended for architectural designer and builder/contractor reference only. NOTES: ■ Vent materials needed for installation are not provided with microwave hood. Rectangular to Round Transition NOTE: The minimum 3" (7.6 cm) clearance must exist between the top of the - Whirlpool MMV4203DQ | Installation Instructions - Page 11
installed to keep the damper from sticking. ASSISTANCE Call your authorized dealer or service center. When you call, you will need the microwave oven model listed in the User Instructions. Accessories Filler Panel Kits are available from your dealer to use when installing this microwave oven in a - Whirlpool MMV4203DQ | Installation Instructions - Page 12
W10188238A SP PN W10188947A © 2008. All rights reserved. DE68-03534A 9/08 Printed in Malaysia
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
 |
 |
MICROWAVE HOOD COMBINATION
INSTALLATION INSTRUCTIONS
MICROWAVE HOOD COMBINATION SAFETY
This product is suitable for use above electric or gas cooking products up to and including 36" (91.4 cm) wide. See “Installation
Requirements” section for further notes.
These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration in
these installation instructions.
Table of Contents
MICROWAVE HOOD COMBINATION SAFETY
..............................
1
INSTALLATION REQUIREMENTS
...................................................
2
Tools and Parts
...............................................................................
2
Location Requirements
...................................................................
2
Product Dimensions
.......................................................................
3
Electrical Requirements
..................................................................
3
INSTALLATION INSTRUCTIONS
.....................................................
4
Remove Mounting Plate
.................................................................
4
Rotate Blower Motor
.......................................................................
4
Locate Wall Stud(s)
.........................................................................
6
Mark Rear Wall
................................................................................
6
Drill Holes in Rear Wall
....................................................................
7
Attach Mounting Plate to Wall
........................................................
7
Prepare Upper Cabinet
...................................................................
8
Install the Microwave Oven
............................................................
8
Complete Installation
......................................................................
9
VENTING DESIGN SPECIFICATIONS
............................................
10
ASSISTANCE
...................................................................................
11
Replacement Parts
.......................................................................
11
Accessories
...................................................................................
11
W10188238A
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING