Whirlpool RS696PXGQ Installation Instructions
Whirlpool RS696PXGQ Manual
 |
View all Whirlpool RS696PXGQ manuals
Add to My Manuals
Save this manual to your list of manuals |
Whirlpool RS696PXGQ manual content summary:
- Whirlpool RS696PXGQ | Installation Instructions - Page 1
.2 CM) DROP-IN CERAMIC ELECTRIC RANGE Table of Contents RANGE SAFETY 1 INSTALLATION REQUIREMENTS 2 Tools and Parts 2 Location Requirements 2 Electrical Requirements 4 Countertop Preparation 4 INSTALLATION INSTRUCTIONS 5 Prepare Drop-In Range 5 Remove Oven Trim 5 Make Electrical Connection - Whirlpool RS696PXGQ | Installation Instructions - Page 2
is located on the right-hand side oven door trim. ■ Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances. ■ Recessed installation area must provide complete enclosure around the recessed portion of the range. ■ Range support slats must be solid, level and - Whirlpool RS696PXGQ | Installation Instructions - Page 3
of cooktop to support slats B. 29 74.2 cm) cooktop recessed width C. 28 71.5 cm) range recessed width D. 24 62 cm) to back of range Cabinet Dimensions Top view between cutout and cabinet door or hinge E. 30³⁄₄" (78.1 cm) top of countertop to bottom of front cabinet cutout/support slats F. 36" - Whirlpool RS696PXGQ | Installation Instructions - Page 4
range hood or microwave hood combination above the range, follow the range hood or microwave hood combination installation instructions line. ■ Do not cut the conduit. The length of conduit provided is for serviceability of the oven. A D B A. Notch width to be equal on both sides B. 30¹⁄₈" (76.5 - Whirlpool RS696PXGQ | Installation Instructions - Page 5
INSTALLATION INSTRUCTIONS Prepare Drop-In Range 1. Decide on the final location for the range. Locate existing wiring to avoid drilling into or severing wiring during installation. 3. Grasp the edges of the oven door with both hands and close the oven door until it stops. Lift and pull oven door - Whirlpool RS696PXGQ | Installation Instructions - Page 6
servicing. Use 8 gauge solid copper wire. Electrically ground oven. Failure to follow these instructions can result in death, fire, or electrical shock. This range I A. Cable from home power supply B. Black wires C. Red wires D. 4-wire flexible cable from range E. Junction box F. White wires G. UL - Whirlpool RS696PXGQ | Installation Instructions - Page 7
Use screws to attach each trim piece to range. 9. Replace oven racks. 10. Replace oven door by inserting ends of hinges into hinge slots in the oven frame. 11. Push hinges in as far as they will go and open the oven door. You should feel the oven door drop into place. 12. Rotate both hinge latches - Whirlpool RS696PXGQ | Installation Instructions - Page 8
. ■ See "Troubleshooting" section in the Use and Care Guide. 4. Turn cooktop control knob to OFF. If you need Assistance or Service: Please reference the "Assistance or Service" section of the Use and Care Guide or contact the dealer from whom you purchased your range. W10055460 © 2007.Whirlpool
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
 |
 |
INSTALLATION INSTRUCTIONS
30" (76.2 CM) DROP-IN CERAMIC ELECTRIC RANGE
RANGE SAFETY
Table of Contents
RANGE SAFETY
.............................................................................
1
INSTALLATION REQUIREMENTS
................................................
2
Tools and Parts
............................................................................
2
Location Requirements
................................................................
2
Electrical Requirements
...............................................................
4
Countertop Preparation
...............................................................
4
INSTALLATION INSTRUCTIONS
..................................................
5
Prepare Drop-In Range
................................................................
5
Remove Oven Trim
......................................................................
5
Make Electrical Connection
.........................................................
6
Install Range
.................................................................................
7
Complete Installation
...................................................................
8
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
W10055460
IMPORTANT:
Save for local electrical inspector's use.