Whirlpool SC8720EDB Installation Instructions
Whirlpool SC8720EDB - GAS DOWNDRAFT Manual
 |
UPC - 050946528700
View all Whirlpool SC8720EDB manuals
Add to My Manuals
Save this manual to your list of manuals |
Whirlpool SC8720EDB manual content summary:
- Whirlpool SC8720EDB | Installation Instructions - Page 1
needed 2 Parts supplied 2 Electrical requirements 3 Gas supply requirements 3 4 Venting requirements 5 6 Installation steps 7 Gas conversions Back cover Cooktop removal 30" GAS Downdraft Cooktop Modules selected at time of purchase. IMPORTANT: Read and save these instructions. Part No. 8101P350 - Whirlpool SC8720EDB | Installation Instructions - Page 2
edge of countertop requirements," Page 2. Proper gas supply connection must be available. See "Gas supply requirements," Page 3. Minimum base cabinet dimensions - Vent system must terminate outdoors. 30" (76.2 cm) base cabinet. All openings in the wall or floor where cooktop is to be 24" (61 - Whirlpool SC8720EDB | Installation Instructions - Page 3
with one satisfactory performance when installing the or more downdraft cooktops. Side clearance - 2" (5.1 cm) minimum clearance is required. 6" (15.2 cm) clearance between side of cooktop and side wall is recommended for maximum ventilation performance. Rear clearance - The rear edge of the - Whirlpool SC8720EDB | Installation Instructions - Page 4
(305 m) above sea level. Type of gas: This downdraft cooktop is factory set for use with Natural gas. It is design- certified by CSA International for Natural or L.P. gas usage with appropriate conversion. (See "Gas conversion" instructions, Page 7). The model/serial rating plate (located on the - Whirlpool SC8720EDB | Installation Instructions - Page 5
vent arrangement under concrete slab Determine range blower setting. This cooktop is equipped with a dual range blower. It is factory set at "Low" range to be used for equivalent vent length runs of 30 range To shift blower to "High" range: 1. Turn blower off. 2. Remove the air grille and filter - Whirlpool SC8720EDB | Installation Instructions - Page 6
the downdraft cooktop from packaging. 2. Check equivalent vent length to determine if blower should be set at "Low" or "High" range (see chart on page 4 to determine equivalent vent system length). If vent system length is greater than 30 feet (9.1m), shift the blower range setting from "Low" to - Whirlpool SC8720EDB | Installation Instructions - Page 7
control knob. • Replace surface burner grates and burner pan or grill grates and burner pan. You have just finished installing your new downdraft cooktop. To get the most efficient use from your new cooktop, read your Use & Care Guide. Keep Installation Instructions and Guide close to cooktop for - Whirlpool SC8720EDB | Installation Instructions - Page 8
3. Remove surface burner and grille modules from cooktop. Remove L.P. gas orifice hoods by turning hoods counterclockwise with 1/2" open-end wrench. Locate color-coded Natural gas orifice hoods in plastic parts bag attached to bottom of cooktop. • Green-colored orifice hoods, drill size #55 - Whirlpool SC8720EDB | Installation Instructions - Page 9
vent system. If cooktop does not operate: ࠜ Check that circuit breaker is not tripped or the house fuse blown. ࠜ Check that the power supply cord is plugged into the wall receptacle. ࠜ Check that the gas supply valves are turned to the "ON" position. ࠜ See Use and Care Guide for troubleshooting
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
 |
 |
Quick Reference
Table of Contents:
Pages
Before you start
Cutout dimensions
Clearance dimensions
Product dimensions
Tools and materials needed
Parts supplied
Electrical requirements
Gas supply requirements
Venting requirements
Installation steps
Gas conversions
Cooktop removal
Need assistance?
Check your Use and Care Guide for a toll-free number to call, or
call the dealer from whom you purchased the cooktop when you:
±
Have questions about the cooktop installation or operation.
±
Need to obtain the name and number of an authorized service
company.
The dealer is listed in the Yellow Pages of your phone directory
under “Appliances — Household — Major — Service and Repair.”
When you call, you will need:
±
The cooktop model number.
±
The cooktop serial number.
Both numbers are listed on the model/serial rating plate, located
on the bottom of the right side of the downdraft plenum.
Write both numbers down now before installing cooktop.
Model #
Serial #
1
1
1
2
2
2
2
3
3
4
5
6
7
Back cover
IMPORTANT:
Read and save these instructions.
Installation Instructions
IMPORTANT:
Installer:
Leave Installation Instructions with the homeowner.
Homeowner:
Keep Installation Instructions for future reference.
Save
Installation Instructions for local electrical inspector's use.
Part No.
8101P350-60/
8284676
30"
GAS
Downdraft Cooktop
Modules selected at time of purchase.