Home » Whirlpool Manuals » Ranges » Whirlpool WEC310SAGW » Manual Viewer

Whirlpool WEC310SAGW Installation Instructions

Whirlpool WEC310SAGW Manual

View all Whirlpool WEC310SAGW manuals

Add to My Manuals
Save this manual to your list of manuals

Whirlpool WEC310SAGW manual content summary:

Whirlpool WEC310SAGW | Installation Instructions - Page 1
of Contents RANGE SAFETY 2 INSTALLATION REQUIREMENTS 3 Tools and Parts 3 Location Requirements 3 Electrical Requirements - U.S.A. Only 5 INSTALLATION INSTRUCTIONS 6 Unpack Range 6 Install Anti-Tip Bracket 6 Adjust Leveling Legs 7 Level Range 8 Electrical Connection - U.S.A. Only 8 Verify
Whirlpool WEC310SAGW | Installation Instructions - Page 2
be killed. Install anti-tip bracket to floor or wall per installation instructions. Slide range back so rear range foot is engaged in the slot range without anti-tip bracket installed and engaged. Failure to follow these instructions can result in death or serious burns to children and adults. Anti
Whirlpool WEC310SAGW | Installation Instructions - Page 3
INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools Needed ■■ Tape measure ■■ Masking tape ■■ Flat-blade screwdriver ■■ 1/4" (6.4 mm) drive ratchet ■■ Phillips
Whirlpool WEC310SAGW | Installation Instructions - Page 4
of range F. 291/64" (73.7 cm) max. depth from handle to back of range IMPORTANT: Range must be level after installation. Follow the instructions in the "Level Range" section. Using the cooktop as a reference for leveling the range is not recommended. * Range can be raised approximately 1" (2.5 cm
Whirlpool WEC310SAGW | Installation Instructions - Page 5
type of electrical connection you will be using and follow the instructions provided for it here. ■■ Range must be connected to the 6 ft (1.8 m) of slack in the line so that the range can be moved if servicing is ever necessary. ■■ A UL Listed conduit connector must be provided at each end of the
Whirlpool WEC310SAGW | Installation Instructions - Page 6
other two corners. Place them lengthwise on the floor behind the range to support the range when it is laid on its back. 4. Using two or more range and be killed. Install anti-tip bracket to floor or wall per installation instructions. Slide range back so rear range foot is engaged in the slot of
Whirlpool WEC310SAGW | Installation Instructions - Page 7
range without anti-tip bracket installed and engaged. Failure to follow these instructions can result in death or serious burns to children and adults. 1. This may be done with the range on its back or with the range supported on two legs after the range has been placed back to a standing position.
Whirlpool WEC310SAGW | Installation Instructions - Page 8
the bottom of the cover toward you and out to remove cover from range. A. UL Listed strain relief 5. Complete installation following instructions for your type of electrical connection: 4-wire (recommended) 3-wire (if 4-wire is not available) Electrical Connection Options A B C A. Mounting tabs
Whirlpool WEC310SAGW | Installation Instructions - Page 9
If your home has: 3-wire receptacle (NEMA type 10-50R) And you will be connecting to: A UL Listed, 250-volt minimum, 40- or 50-amp, range power supply cord Go to Section: 3-Wire Connection: Power Supply Cord 2. Use 3⁄8" (9.5 mm) nut driver to connect the neutral (white) wire to the center
Whirlpool WEC310SAGW | Installation Instructions - Page 10
post with one of the 10-32 hex nuts. Electrical Shock Hazard Disconnect power before servicing. Use 8 gauge copper or 6 gauge aluminum wire. Electrically ground range. Failure to follow these instructions can result in death, fire, or electrical shock. Direct Wire Strain Relief 1. Disconnect power
Whirlpool WEC310SAGW | Installation Instructions - Page 11
terminal blocks and set aside. 2. Allow enough slack in the wire to easily attach the wiring terminal block. 3. Complete installation following instructions for your type of electrical connection: 4-wire (recommended) 3-wire (if 4-wire is not available) Electrical Connection Options If your home
Whirlpool WEC310SAGW | Installation Instructions - Page 12
2. Attach terminal lugs to line two (red), bare (green) ground, and line one (black) wires. Loosen (do not remove) the setscrew on the front of the terminal lug and insert exposed wire end through bottom of terminal lugs. Securely tighten setscrew to torque as shown in the following Bare Wire Torque
Whirlpool WEC310SAGW | Installation Instructions - Page 13
4. Attach terminal lugs to line one (black), neutral (white), and line two (red) wires. Loosen (do not remove) the setscrew on the front of the terminal lug and insert exposed wire end through bottom of terminal lugs. Securely tighten setscrew to torque as shown in the following Bare Wire Torque
Whirlpool WEC310SAGW | Installation Instructions - Page 14
, it is not suggested to remove the oven door. However, if removal is necessary, make sure the oven is off and cool. Then, follow these instructions. The oven door is heavy. To Remove: 1. Open oven door all the way. 2. Pinch the hinge latch between two fingers and pull forward. Repeat on
Whirlpool WEC310SAGW | Installation Instructions - Page 15
Turn power on. 9. Turn on surface elements and oven. See the User Guide for specific instructions on range operation. NOTE: Odors and smoke are normal when the oven is electrician. If You Need Assistance or Service: Please reference the "Warranty" section of the User Guide to contact service. 15
Whirlpool WEC310SAGW | Installation Instructions - Page 16
W11097823B ©2017 All rights reserved. 04/17