Home » Whirlpool Manuals » Laundry Dryers » Whirlpool WED4900XW » Manual Viewer

Whirlpool WED4900XW Installation Instructions

Whirlpool WED4900XW Manual

UPC - 883049200064

View all Whirlpool WED4900XW manuals

Add to My Manuals
Save this manual to your list of manuals

Whirlpool WED4900XW manual content summary:

Whirlpool WED4900XW | Installation Instructions - Page 1
Electric Dryer Installation Instructions 29" Wide Models - U.S.A. Only Para obtener acceso al manual de uso y cuidado en español, o para obtener información adicional acerca de su producto, visite: www.whirlpool.com Tenga listo su número de modelo completo. Puede encontrar el número de modelo y de
Whirlpool WED4900XW | Installation Instructions - Page 2
. INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools needed: Flat-blade screwdriver 2 #2 Phillips screwdriver Wire stripper (direct wire installations) Tin snips
Whirlpool WED4900XW | Installation Instructions - Page 3
Requirements." ■■ A separate 30 amp circuit. ■■ If you are using power supply cord, a grounded electrical outlet located within 2 ft. (610 mm) of either side of dryer. See "Electrical Requirements." ■■ A sturdy floor to support the total weight (dryer and load) of 200 lbs. (90.7 kg). The combined
Whirlpool WED4900XW | Installation Instructions - Page 4
must determine the type of electrical connection you will be using and follow the instructions provided for it here. ■■ If local codes do not permit the connection of a neutral ground wire to the neutral wire, see "Optional 3-wire connection" section. ■■ This dryer is manufactured ready to install
Whirlpool WED4900XW | Installation Instructions - Page 5
If using a power supply cord: Use a UL listed power supply cord kit marked for use with clothes dryers. The kit should contain: ■■ A UL listed 30-amp power supply cord, rated 120/240 volt minimum. The cord should be type SRD or SRDT and be at least 4 ft. (1.22 m) long. The wires that connect to the
Whirlpool WED4900XW | Installation Instructions - Page 6
in death, fire, or electrical shock. Electrical Connection Options 1. Choose electrical connection type Power supply cord 4-wire receptacle (NEMA Type 14-30R): Go to steps 1-2 on page 6 for power supply cord strain relief: then steps 3-6 for 4-wire Power Supply Cord Connection section. Then, go
Whirlpool WED4900XW | Installation Instructions - Page 7
The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Do not further tighten strain relief screws at this point. For 3-wire Power Supply Cord Connection, see page 8. For 4 wire Power Supply Cord Connection, continue to step 3 on this page. E Remove center
Whirlpool WED4900XW | Installation Instructions - Page 8
block cover into slot of dryer rear panel. Secure cover with hold-down screw. Now, go to Venting Requirements. Remove center, silver-colored terminal block screw (B). 4. Connect neutral wire BC Connect neutral wire (white or center) (C) of power supply cord to center, silver-colored terminal
Whirlpool WED4900XW | Installation Instructions - Page 9
terminal block opening, screw the removable conduit connector onto the strain relief threads (C). 2. Attach direct wire cable to strain relief (127 5" mm) Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer may be moved if needed. Strip 5" (127 mm) of outer covering from end of
Whirlpool WED4900XW | Installation Instructions - Page 10
cable under center screw of terminal block (B). Squeeze hooked ends together and tighten screw. 7. Connect ground wire A (893m½m" ) Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer may be moved if needed. Strip 31/2" (89 mm) of outer covering from end of cable. Strip insulation
Whirlpool WED4900XW | Installation Instructions - Page 11
. 7. Connect remaining wires E Connect neutral ground wire (E) and neutral wire (white or center wire) (C) of power supply cord or cable under center cover into slot of dryer rear panel. Secure cover with hold-down screw. Now, go to Venting Requirements. Optional 3-wire Connection You must verify
Whirlpool WED4900XW | Installation Instructions - Page 12
or metal foil vent. Rigid metal vent: ■■ Recommended for best drying performance and to avoid crushing and kinking. Flexible metal vent: (Acceptable only if accessible to clean) ■■ Must be fully extended and supported in final dryer location. ■■ Remove excess to avoid sagging and kinking that may
Whirlpool WED4900XW | Installation Instructions - Page 13
Select the type best for your installation. Two close-clearance installations are shown. Refer to the manufacturer's instructions. A A. Dryer B. Elbow C. 1-800-807-6777 or visit us at www.whirlpoolparts.ca. Part Number Descriptions 8171587RP 0-5" Metal vent periscope 4396037RP 0"-18" Metal vent
Whirlpool WED4900XW | Installation Instructions - Page 14
Vent Models Only) Number of will: ■■ Shorten life of dryer. ■■ Reduce performance, resulting in longer drying times and increased energy usage. The Vent system chart provides venting requirements that will help achieve best drying performance. 4 Rigid metal 5 Rigid metal 80 ft. (24.4 m) 70 ft
Whirlpool WED4900XW | Installation Instructions - Page 15
Care Guide. q Set the dryer on a full heat cycle (not an air cycle) for 20 minutes and start the dryer. If the dryer will not start, check the following: ■■ Controls are set in a running or "On" position. ■■ Start button has been pushed firmly. ■■ Dryer is plugged into an outlet and/or electrical
Whirlpool WED4900XW | Installation Instructions - Page 16
an odor when the dryer is first heated. This odor is common when the heating element is first used. The odor will go away. Reverse Door dryer Lift door until top screws in cabinet are in large part of hinge slot. Pull door forward off screws. Set door on top of dryer. Remove top screws from dryer
Whirlpool WED4900XW | Installation Instructions - Page 17
with door catch. If needed, slide door catch left or right within slot to adjust alignment. Super Wide Side-Swing Door 1. Place towel on dryer Lift door until top screws in dryer cabinet are in large part of hinge slot. Pull door forward off screws. Set door (handle side up) on top of
Whirlpool WED4900XW | Installation Instructions - Page 18
separate from hinge screws as they are diferent sizes. Holding door over towel on dryer, grasp sides of outer door and lift to separate it from inner door. removed. Insert 4 door screws. 7. Flip door over Reattach door hinges to dryer door so that the larger hole is at the bottom of the hinge. 9.
Whirlpool WED4900XW | Installation Instructions - Page 19
dryer cabinet. Transfer plugs into hinge holes on opposite side of dryer cabinet. 11. Insert screws in hinge holes on dryer into the bottom holes on left side of dryer cabinet. Tighten screws halfway. Position door so large Troubleshooting See the Use and Care Guide or visit our website and
Whirlpool WED4900XW | Installation Instructions - Page 20
W10096987A W10097001A-SP 2©Al0l2r0ig1h0tsWrehsirelprvoeodl Corporation. ® Registered Trademark/TM Trademark of Whirlpool, U.S.A. 2/10 Printed in U.S.A.