Home » Whirlpool Manuals » Laundry Dryers » Whirlpool WED7300XW » Manual Viewer

Whirlpool WED7300XW Installation Instructions

Whirlpool WED7300XW Manual

UPC - 883049202747

View all Whirlpool WED7300XW manuals

Add to My Manuals
Save this manual to your list of manuals

Whirlpool WED7300XW manual content summary:

Whirlpool WED7300XW | Installation Instructions - Page 1
Instructions Table of Contents DRYER SAFETY 2 Installation Requirements 3 Tools and Parts 3 Location Requirements 4 Electrical Requirements 5 Install Leveling Legs 6 Electrical Connection 6 VENTING 12 Venting Requirements 12 Plan Vent System 13 Install Vent System 14 CONNECT INLET HOSES
Whirlpool WED7300XW | Installation Instructions - Page 2
DRYER SAFETY 2
Whirlpool WED7300XW | Installation Instructions - Page 3
) Tin snips (new vent installations) 1/4" nut driver (recommended) Tape measure 5' inlet hose Rubber washer Parts package is located in dryer drum. Check that all parts are included. Parts needed: (Not supplied with dryer) Check local codes. Check existing electrical supply and venting. See
Whirlpool WED7300XW | Installation Instructions - Page 4
side of dryer. See "Electrical Requirements." ■■ Floor must support dryer weight of 200 lbs. (90.7 kg). Also consider weight of companion appliance. ■■ Level floor with maximum slope of 1" (25 mm) under entire dryer. If slope is greater than 1" (25 mm), install Extended Dryer Feet Kit, Part Number
Whirlpool WED7300XW | Installation Instructions - Page 5
. ■■ If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate. Electrical Connection To properly install your dryer, you must determine the type of electrical connection you will be using and follow the instructions
Whirlpool WED7300XW | Installation Instructions - Page 6
Install Leveling Legs Electrical Connection Power Supply Cord 1. Prepare dryer for leveling legs To avoid damaging floor, use a large flat piece of cardboard from dryer carton; place under entire back edge of dryer. Firmly grasp dryer body (not console panel) and gently lay dryer down on
Whirlpool WED7300XW | Installation Instructions - Page 7
wire connection is required for mobile homes and where local codes do not permit the use of 3-wire connections. Remove the screws from a 3/4" (19 mm) UL listed strain relief (UL marking on strain relief). Put the tabs fit with the dryer cabinet and be in a horizontal position. Do not further tighten
Whirlpool WED7300XW | Installation Instructions - Page 8
wire and neutral wire 3-wire Power Supply Cord Connection Use where local codes permit connecting cabinet-ground conductor to neutral wire. E B C 3- Tighten screws. Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. Now, go to "
Whirlpool WED7300XW | Installation Instructions - Page 9
required for mobile homes and where local codes do not permit 3-wire connections. 1. Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer may be moved if needed. Strip 5" (127 mm) of outer covering screws from a 3/4" (19 mm) UL listed strain relief (UL marking on strain relief). Put
Whirlpool WED7300XW | Installation Instructions - Page 10
to "Venting Requirements". 3-wire Direct Wire Connection Use where local codes permit connecting cabinet-ground conductor to neutral wire. 1. Prepare 893m½m" ) Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer may be moved if needed. Strip 31/2" (89 mm) of outer covering from end
Whirlpool WED7300XW | Installation Instructions - Page 11
terminal block screws (hooks facing right). Squeeze hooked ends together and tighten screws. Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. Now, go to "Venting Requirements". Optional 3-wire Connection You must verify with a qualified
Whirlpool WED7300XW | Installation Instructions - Page 12
supported in final dryer location. ■■ Remove excess to avoid sagging and kinking that may result in reduced airflow and poor performance. ■■ Do not install is not plugged with lint. Replace plastic or metal foil vents with rigid metal or flexible metal vents. Review Vent System Chart and if necessary
Whirlpool WED7300XW | Installation Instructions - Page 13
cover unused exhaust holes): Part Number W10186596 - all models ■■ Bottom Exhaust Kit- Part Number 8212503 If you prefer, dryer may be converted to exhaust through the bottom. You must contact your local dealer to have dryer converted. Moblie Home Exhaust installation A B A. Standard rear offset
Whirlpool WED7300XW | Installation Instructions - Page 14
they can catch lint. CONNECT INLET HOSES For non-steam models, skip to "Connect Vent" on page 16. The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses. 1. Turn cold water off, remove and replace rubber washer Turn cold water faucet off and remove
Whirlpool WED7300XW | Installation Instructions - Page 15
connector. 3. Tighten couplings Attach other end of long hose to fill valve at bottom of dryer back panel. Screw on coupling by hand until it is end of the long hose has a wire mesh strainer inside the coupling. Attach this end to the "Y" connector. Attach washer cold inlet hose to other side of
Whirlpool WED7300XW | Installation Instructions - Page 16
Place level here Place level here Using a 4" (102 mm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure vent is clean. Dryer vent must fit over dryer exhaust outlet and inside exhaust hood. Check that vent is secured to exhaust hood with a 4" (102 mm) clamp
Whirlpool WED7300XW | Installation Instructions - Page 17
scale buildup may lead to the need for certain part replacement or repair. All Models: q Select a Time Dry heated cycle, and start dryer. Do not select Air Only Temperature setting. If dryer will not start, check the following: • Controls are set in a running or "On" position. • Start button has
Whirlpool WED7300XW | Installation Instructions - Page 18
Remove the 4 screws and two hinges from the dryer door. 6. Hang door by placing screw heads into top slotted holes of hinges and slide door down. Align bottom screw holes in hinge and door. Install two bottom screws. Tighten all hinge screws. 2. Replace the 4 screws in the same holes 3. Remove
Whirlpool WED7300XW | Installation Instructions - Page 19
or breakers. Replace the fuse or reset the circuit breaker. Confirm the power cord is properly installed. Refer to "Electrical Connection" for details. Select a Timed Dry heated cycle, and restart the dryer. If the message persists, consult a qualified electrician. ■■ "AF" (low airflow condition
Whirlpool WED7300XW | Installation Instructions - Page 20
openings at the top and bottom of the door. The front of the dryer requires a minimum of 1" (25 mm) of airspace, and, for most installations, the rear of the dryer requires 5" (127 mm). See "Installation Instructions". W10347663A W10325825A-SP © 2010 All rights reserved 09/10 Printed in U.S.A.