Whirlpool WED9151YW Installation Guide
Whirlpool WED9151YW Manual
 |
View all Whirlpool WED9151YW manuals
Add to My Manuals
Save this manual to your list of manuals |
Whirlpool WED9151YW manual content summary:
- Whirlpool WED9151YW | Installation Guide - Page 1
19 DOOR REVERSAL KIT (OPTIONAL 20 STACKING WASHER AND DRYER (OPTIONAL 20 TROUBLESHOOTING 20 Para una version de estas instrucciones en español, visite www.Whirlpool.com INSTALLATION NOTES Date of purchase Date of installation Installer Model number Serial number W10385103B W10385104B - SP 1 - Whirlpool WED9151YW | Installation Guide - Page 2
DRYER SAFETY IMPORTANT: When discarding or storing your old clothes dryer, remove the door. 2 - Whirlpool WED9151YW | Installation Guide - Page 3
Caulking gun and compound (for installing new exhaust vent) Short inlet hose (steam models only) Long inlet hose (steam models only) Rubber washers (steam models only) Optional Equipment: (Not supplied with dryer) Refer to your Use and Care Guide for information about accessories available for - Whirlpool WED9151YW | Installation Guide - Page 4
location allowing for proper exhaust installation. See "Venting Requirements." ■■A separate 30 amp circuit. ■■If using power supply cord, a grounded electrical outlet located within 2 ft. (610 mm) of either side of dryer. See "Electrical Requirements." ■■Floor must support dryer weight of 200 lbs - Whirlpool WED9151YW | Installation Guide - Page 5
for recessed area or closet installation All dimensions show recommended and minimum spacing allowed. ■■Additional spacing should be considered for ease of installation and servicing. ■■Additional clearances might be required for wall, door, floor moldings, dryer venting, and gas line. ■■Additional - Whirlpool WED9151YW | Installation Guide - Page 6
recommended that a qualified electrician determine that the ground path is adequate. Electrical Connection To properly install your dryer, you must determine the type of electrical connection you will be using and follow the instructions provided for it here. If your outlet looks like this: 4-wire - Whirlpool WED9151YW | Installation Guide - Page 7
INSTALL LEVELING LEGS 1. Prepare dryer for leveling legs To avoid damaging floor, use a large flat piece of cardboard from dryer carton; place under entire back edge of dryer. Firmly grasp dryer body (not console panel) and gently lay dryer down on cardboard. 2. Screw in leveling legs diamond - Whirlpool WED9151YW | Installation Guide - Page 8
For power supply cord installations: For direct wire installations: Before you start: disconnect power. 1. Choose electrical connection type Power supply cord 4-wire receptacle (NEMA Type 14-30R). Go to Power Supply Cord Connection. Power supply cord 3-wire receptacle (NEMA Type 10- - Whirlpool WED9151YW | Installation Guide - Page 9
. Be sure that the wire insulation on the power supply cord is inside the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Do not further tighten strain relief screws at this point. If your outlet looks like this: Power supply cord - Whirlpool WED9151YW | Installation Guide - Page 10
neutral wire B C Connect remaining wires under outer terminal block screws. Tighten screws. Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. Now, go to Venting Requirements. Connect neutral wire (white or center) (C) of power supply - Whirlpool WED9151YW | Installation Guide - Page 11
. 1. Prepare your 4-wire cable for direct connection 31 (89 ⁄2" mm) (251"mm) (127 5" mm) Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer may be moved if needed. Strip 5" (127 mm) of outer covering from end of cable, leaving bare ground wire at 5" (127 mm). Cut 11/2" (38 - Whirlpool WED9151YW | Installation Guide - Page 12
block (B). Squeeze hooked ends together and tighten screw. 4. Connect ground wire (893m½m" ) Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer may be moved if needed. Strip 31/2" (89 mm) of outer covering from end of cable. Strip insulation back 1" (25 mm). If using 3-wire cable - Whirlpool WED9151YW | Installation Guide - Page 13
tighten screws. Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. Now, go to screws. Tighten screws. A 4. Connect external ground wire Install the correct strain relief for your electrical connection method, as shown on page 9 or 11 - Whirlpool WED9151YW | Installation Guide - Page 14
supported in final dryer location. ■■ Remove excess to avoid sagging and kinking that may result in reduced airflow and poor performance. ■■ Do not install plastic or metal foil vents with rigid metal or flexible metal vents. Review Vent System Chart and if necessary, modify existing vent system to - Whirlpool WED9151YW | Installation Guide - Page 15
Plan Vent System Choose your exhaust installation type Recommended exhaust installation: B A F G Alternate exhaust installations (for close clearance): C D E A. Dryer B Elbow C. Wall D. Exhaust hood E. Clamps B H F. Rigid metal or flexible metal vent G. Vent length necessary to connect elbows H. - Whirlpool WED9151YW | Installation Guide - Page 16
venting requirements that will help achieve best drying performance. NOTE: Side and bottom exhaust installation have a 90° turn inside the dryer. To determine maximum exhaust length, add one 90° turn to the chart. Install Vent System 1. Install exhaust hood 12" min. (305 mm) 12" min. (305 mm - Whirlpool WED9151YW | Installation Guide - Page 17
HOSE (Steam models only) For non-steam models, proceed to "Connect Vent". The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses. NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record hose installation or replacement - Whirlpool WED9151YW | Installation Guide - Page 18
VENT 1. Connect vent to exhaust outlet Remove protective cap from water inlet valve. Attach other end of long hose to fill valve at bottom of dryer back panel. Screw on coupling by hand until it is seated on fill valve connector. Using pliers, tighten the couplings an additional two-thirds turn - Whirlpool WED9151YW | Installation Guide - Page 19
any tape remaining on dryer. q Wipe dryer drum interior thoroughly with a damp cloth to remove any dust. q Read "Dryer Use" in your Use and Care Guide. q For power supply cord installation, plug into a grounded outlet. For direct wire installation, turn on Power. Steam Models Only: q Be sure - Whirlpool WED9151YW | Installation Guide - Page 20
) If you prefer to stack your washer and dryer: A stack kit, Part Number 8572546, is available to order. For further information, see "Assistance or Service" section in your "Use and Care Guide". TROUBLESHOOTING See your "Use and Care Guide" or visit our website and reference Frequently Asked
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
 |
 |
W10385103B
W10385104B - SP
Table of Contents
DRYER SAFETY
.........................................................................
2
INSTALLATION REQUIREMENTS
.............................................
3
Tools and Parts
......................................................................
3
LOCATION REQUIREMENTS
....................................................
4
ELECTRICAL REQUIREMENTS
................................................
6
INSTALL LEVELING LEGS
.........................................................
7
ELECTRICAL INSTALLATION
...................................................
8
Power Supply Cord Connection
...........................................
9
Direct Wire Connection
.......................................................
11
VENTING
...................................................................................
14
Venting Requirements
.........................................................
14
Plan Vent System
.................................................................
15
Venting Kits
..........................................................................
15
Install Vent System
..............................................................
16
CONNECT INLET HOSE
..........................................................
17
CONNECT VENT
......................................................................
18
LEVEL DRYER
..........................................................................
19
COMPLETE INSTALLATION CHECKLIST
..............................
19
DOOR REVERSAL KIT (OPTIONAL)
.......................................
20
STACKING WASHER AND DRYER (OPTIONAL)
...................
20
TROUBLESHOOTING
..............................................................
20
ELECTRIC DRYER INSTALLATION INSTRUCTIONS
INSTALLATION NOTES
Date of purchase:
_________________________________
Date of installation:
_______________________________
Installer:
________________________________________
Model number:
___________________________________
Serial number:
___________________________________
Para una version de estas instrucciones en español, visite www.Whirlpool.com