Whirlpool WED9270XL Installation Instructions
Whirlpool WED9270XL Manual
 |
View all Whirlpool WED9270XL manuals
Add to My Manuals
Save this manual to your list of manuals |
Whirlpool WED9270XL manual content summary:
- Whirlpool WED9270XL | Installation Instructions - Page 1
ELECTRIC DRYER INSTALLATION INSTRUCTIONS Para obtener acceso al manual de uso y cuidado en español, o para obtener información adicional acerca de su producto, visite: www.whirlpool.com Tenga listo su número de modelo completo. Puede encontrar el número de modelo y de serie dentro de la cavidad - Whirlpool WED9270XL | Installation Instructions - Page 2
DRYER SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance don't immediately follow instructions. WARNING You can be killed or seriously injured if you don't follow instructions. All safety messages - Whirlpool WED9270XL | Installation Instructions - Page 3
package is located in dryer drum. Check that all parts are included. NOTE: If installing dryer on pedestal, do not use leveling legs. Optional Equipment: (Not supplied with dryer) Refer to your Use and Care Guide for information about accessories available for your dryer. Parts needed: (Not supplied - Whirlpool WED9270XL | Installation Instructions - Page 4
25 mm), install Extended Dryer Feet Kit, Part Number 279810. If not level, clothes may not tumble properly and automatic sensor cycles may not operate correctly. For each arrangement, consider allowing more space for ease of installation and servicing; spacing for companion appliances and clearances - Whirlpool WED9270XL | Installation Instructions - Page 5
, install, or store dryer where it will be exposed to water, weather, or at temperatures below 45° F (7° C). Lower temperatures may cause dryer not rear. ■■ Additional spacing should be considered for ease of installation and servicing. ■■ Additional clearances might be required for wall, door, and - Whirlpool WED9270XL | Installation Instructions - Page 6
and Safety, Title 24, HUD Part 280) or Standard CAN/CSA-Z240 MH. Mobile home installations require: ■■ Metal exhaust system hardware, available for purchase from your dealer. For further information, see "Assistance or Service" section in your Use and Care Guide. ■■ Special provisions must be made - Whirlpool WED9270XL | Installation Instructions - Page 7
electrician or service representative or personnel if you are in doubt as to whether the dryer is properly grounded. Do not modify the plug provided with the dryer: if it will not fit the outlet, have a proper outlet installed by a qualified electrician. SAVE THESE INSTRUCTIONS Examine leveling - Whirlpool WED9270XL | Installation Instructions - Page 8
Electrical Connection Power Supply Cord Direct Wire WARNING WARNING Fire Hazard use a new ul listed 30 amp power supply cord. use a ul listed strain relief. Disconnect power before making electrical connections. Connect neutral wire (white or center wire) to center terminal (silver). Ground - Whirlpool WED9270XL | Installation Instructions - Page 9
supply cord through strain relief. Be sure that wire C insulation on power cord is inside strain relief. Strain relief should be a tight fit with dryer cabinet and be in a horizontal position. Do not tighten strain relief screws at this point. B Now go to step 5 for 4-wire power supply cord - Whirlpool WED9270XL | Installation Instructions - Page 10
neutral wire C B Connect remaining wires to outer terminal block screws. Tighten screws. Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. Now, go to Venting Requirements. 3-wire Power supply cord Connection Use where local codes - Whirlpool WED9270XL | Installation Instructions - Page 11
5" mm) Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer may be moved if needed. Strip 5" (127 mm) of outer covering from end of cable through strain relief. Strain relief should be a tight fit with dryer cabinet and be in a horizontal position. Tighten strain relief screw - Whirlpool WED9270XL | Installation Instructions - Page 12
"mm) (893m½m" ) Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer may be moved if needed. Strip 31/2" (89 mm) of outer covering from end of cable. screws. Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. Now, go to - Whirlpool WED9270XL | Installation Instructions - Page 13
block screws (hooks facing right). Squeeze hooked ends together and tighten screws. Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. Now, go to Venting Requirements. Optional 3-wire Connection You must verify with a qualified electrician - Whirlpool WED9270XL | Installation Instructions - Page 14
supported in final dryer location. ■■ Remove excess to avoid sagging and kinking that may result in reduced airflow and poor performance. ■■ Do not install plastic or metal foil vents with rigid metal or flexible metal vents. Review Vent system chart and if necessary, modify existing vent system to - Whirlpool WED9270XL | Installation Instructions - Page 15
problems and health problems. Alternate exhaust installations (for close clearance): Vent products can be purchased from your dealer. For further information, see "Assistance or Service" section in your Use and Care Guide these instructions can result in death or fire. Periscope installation - Whirlpool WED9270XL | Installation Instructions - Page 16
. NOTE: Side and bottom exhaust installation have a 90° turn inside the dryer. To determine maximum exhaust length, add Rigid metal 27 ft. (8.2 m) 21 ft. (6.4 m) INStall VENT SYSTEM 31. Install exhaust hood 12" min. (305 mm) Turn cold water faucet off and remove washer inlet hose. Check and see if - Whirlpool WED9270XL | Installation Instructions - Page 17
of the "Y" connector to the cold water faucet. See figure A. If "Y" connector cannot be attached directly to the cold water faucet, the short hose must be used result. Attach other end of long hose to fill valve at bottom of dryer back panel. Screw on coupling by hand until it is seated on fill - Whirlpool WED9270XL | Installation Instructions - Page 18
38. Turn on cold water faucet 41. Move dryer to final location Check that the water faucets are turned on. 39. Check for leaks Check for leaks around "Y" connector, faucet, and hoses. Connect vent 40. Connect vent to exhaust outlet Move dryer to final location, taking care not to crush or kink - Whirlpool WED9270XL | Installation Instructions - Page 19
If you prefer to reverse the door swing on your dryer: ■■ A door reversal kit, Part Number W10277499 is available to order. For further information, see "Assistance or Service" section in your Use and Care Guide. Troubleshooting See the Use and Care Guide for troubleshooting information. 19 - Whirlpool WED9270XL | Installation Instructions - Page 20
W10240579B W10240583B-SP © 2009 2Al0l rights reserved 12/09 Printed in U.S.A.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
 |
 |
W10240579B
W10240583B-SP
Table of Contents
DRYER SAFETY
.........................................................................
2
INSTALLATION REQUIREMENTS
.............................................
3
Tools and Parts
......................................................................
3
Location Requirements
.........................................................
4
Electrical Requirements
........................................................
6
Install Leveling Legs
..............................................................
7
Electrical Connection
............................................................
8
Venting Requirements
.........................................................
14
Plan Vent System
.................................................................
15
Install Vent System
..............................................................
16
Connect Inlet Hose
..............................................................
16
Connect Vent
........................................................................
18
Level Dryer
...........................................................................
18
COMPLETE INSTALLATION CHECKLIST
..............................
19
DOOR REVERSAL
....................................................................
19
TROUBLESHOOTING
..............................................................
19
ELECTRIC DRYER INSTALLATION INSTRUCTIONS
INSTALLATION NOTES
Date of purchase:
_________________________________
Date of installation:
_______________________________
Installer:
________________________________________
Model number:
___________________________________
Serial number:
___________________________________
Para obtener acceso al manual de uso y cuidado en español, o para obtener información adicional acerca de su producto, visite:
www.whirlpool.com
Tenga listo su número de modelo completo. Puede encontrar el número de modelo y de serie dentro de la cavidad superior de la puerta.