Whirlpool WEG760H0DS Use & Care Guide - Page 7

KEYPAD FEATURE INSTRUCTIONS AQUALIFT Clean cycle SELF CLEAN See the "Clean Cycle" section. START (hold 3 sec to lock) Oven control lockout 1. Check that the oven is off. 2. Press and hold START (hold 3 sec to lock) for 3 seconds. 3. A tone will sound, and "Control Locked" will scroll, then "Locked" will be displayed. 4. Repeat to unlock. No keypads will function with the controls locked. The cooktop functions are not affected by the oven control lockout. ENERGY SAVE Puts the range into sleep mode to reduce energy usage 1. Press and hold SETTINGS/CLOCK for 3 seconds to change status. The display will scroll "Energy saver on" or "Energy saver off." If Energy Save is on, the range will go into sleep mode after 5 minutes of inactivity. Any key press will activate the display. If Energy Save is off, the display will be on at all times. Electronic Oven Controls Control Display The display will flash when powered up or after a power loss. Press CANCEL to clear. When the oven is not in use, the time of day is displayed. If the range is in Energy Save mode, the display will be blank when not in use. Tones Tones are audible signals, indicating the following: One tone ■ Valid pad press ■ Oven is preheated (long tone) ■ Function has been entered ■ Reminder, repeating each minute after the end-of-cycle tones Three tones ■ Invalid pad press Four tones ■ End of cycle Use the Settings/Clock key to change the tone settings. Energy Save The Energy Save mode puts the range into sleep mode and reduces energy consumption. To Activate the Energy Save Mode: 1. Press and hold SETTINGS/CLOCK for 3 seconds. "Energy saver on." will appear in the display. 2. The setting will be activated after 5 minutes. To Deactivate the Energy Save Mode: 1. Press and hold SETTINGS/CLOCK for 3 seconds. "Energy saver off." will appear in the display. 2. The clock will reappear in the display, and the range can be operated as usual. Settings Many features of the oven control can be adjusted to meet your personal needs. These changes are made using the Settings/ Clock key. Use the Settings/Clock key to scroll through the features that can be changed. Each press of the Settings/Clock key will advance the display to the next setting. After selecting the feature to be changed, the control will prompt you for the required input. After the setting is saved by pressing Start, press CANCEL to exit Settings and display the time of day. Details of all of the feature changes are explained in the following sections. Press CANCEL to exit Settings. Clock The Clock can use a 12- or 24-hour cycle. 1. Press SETTINGS/CLOCK until "CLOCK" is displayed. 2. Press START to change the time. 3. Press "3" for AM or "6" for PM. 4. Use the number keypad to set the time of day. 5. Press SETTINGS/CLOCK or START to save the setting. 6. Press CANCEL to exit and display the time of day. Fahrenheit and Celsius The temperature is preset at Fahrenheit, but can be changed to Celsius. 1. Press SETTINGS/CLOCK until "TEMP UNIT" is displayed. 2. The current setting will be displayed. 3. Press the "1" keypad to adjust the setting. 4. Press START or CANCEL to exit and display the time of day. Audible Tones Disable Turns off all tones, including the end of cycle tone and key press tones. Reminder tones are still active when all tones are disabled. 1. Press SETTINGS/CLOCK until "SOUND" is displayed. 2. The current setting will be displayed. 3. Press the "1" keypad to adjust the setting. 4. Press START or CANCEL to exit and display the time of day. Sound Volume Sets the pitch of the tone to either high or low. 1. Press SETTINGS/CLOCK until "SOUND VOLUME" is displayed. 2. The current setting will be displayed. 3. Press the "1" keypad to adjust the setting. 4. Press START or CANCEL to exit and display the time of day. End of Cycle Tone Activates or turns off the tones that sound at the end of a cycle. 1. Press SETTINGS/CLOCK until "END TONE" is displayed. 2. The current setting will be displayed. 3. Press the "1" keypad to adjust the setting. 4. Press START or CANCEL to exit and display the time of day. 7