Whirlpool WFE366LVT Installation Instructions
Whirlpool WFE366LVT - 30 IN SC CLEANTOP CERAN5 Manual
 |
UPC - 883049138756
View all Whirlpool WFE366LVT manuals
Add to My Manuals
Save this manual to your list of manuals |
Whirlpool WFE366LVT manual content summary:
- Whirlpool WFE366LVT | Installation Instructions - Page 1
INSTALLATION INSTRUCTIONS 30" (76 CM) FREESTANDING ELECTRIC RANGES Table of Contents RANGE SAFETY 2 INSTALLATION REQUIREMENTS 3 Tools and Parts 3 Location Requirements 3 Electrical Requirements - U.S.A. Only 4 INSTALLATION INSTRUCTIONS 6 Unpack Range 6 Install Anti-Tip Bracket 6 Electrical - Whirlpool WFE366LVT | Installation Instructions - Page 2
RANGE SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and the range and be killed. Connect anti-tip bracket to rear range foot. Reconnect the anti-tip bracket, if the range is moved. Failure to follow these instructions - Whirlpool WFE366LVT | Installation Instructions - Page 3
require longer screws to anchor bracket to subfloor. Longer screws are available from your local hardware store. Parts needed If using a power supply cord kit: ■ A UL listed power supply cord kit marked for use with ranges. The cord should be rated at 250 volts minimum, 40 amps or 50 amps that is - Whirlpool WFE366LVT | Installation Instructions - Page 4
Model/serial rating plate (located on the left side frame behind storage drawer panel) *Range can max. from floor F 2.2 cm) min. required between cutout and cabinet door or hinge. *NOTE: 24" (61.0 cm) minimum when bottom of of electric shock. Check with a qualified electrician or service technician - Whirlpool WFE366LVT | Installation Instructions - Page 5
you will be using and follow the instructions provided for it here. ■ Range must be connected to the proper electrical voltage and frequency as specified on the model/serial number rating plate. The model/serial number rating plate is located behind the control panel or on the oven frame behind the - Whirlpool WFE366LVT | Installation Instructions - Page 6
INSTALLATION INSTRUCTIONS Unpack Range WARNING Excessive Weight Hazard Use two or more people to move and install range. Failure to do so can result in back or other injury. 1. Remove shipping materials, tape and film from range. 2. Remove oven racks and parts package from inside oven. 3. Do not - Whirlpool WFE366LVT | Installation Instructions - Page 7
grounded outlet. Failure to follow these instructions can result in death, fire, or electrical shock. Electrical Shock Hazard Disconnect power before servicing. Use 8 gauge copper or 6 gauge aluminum wire. Electrically ground range. Failure to follow these instructions can result in death, fire, or - Whirlpool WFE366LVT | Installation Instructions - Page 8
UL listed, 250-volt minimum, 40-amp, range instructions for your type of electrical connection: 4-wire (recommended) 3-wire (if 4-wire is not available) A. Metal ground strap B. Discard C. Ground-link screw 2. Use a Phillips screwdriver to remove the ground-link screw from the back of the range - Whirlpool WFE366LVT | Installation Instructions - Page 9
block B. Ground-link screw C. UL listed strain relief D. Power supply cord wires - large opening 2. Use ³⁄₈" nut driver to connect the neutral use with nominal 1³⁄₈" (3.5 cm) diameter connection opening, with ring terminals and marked for use with ranges. 8. Tighten strain relief screws. 9. Replace - Whirlpool WFE366LVT | Installation Instructions - Page 10
to your type of electrical supply (4-wire or 3-wire connection). 4-wire Connection: Direct Wire Use this method for: ■ New branch-circuit installations (1996 NEC) ■ Mobile homes ■ Recreational vehicles ■ In an area where local codes prohibit grounding through the neutral 1. Part of metal ground - Whirlpool WFE366LVT | Installation Instructions - Page 11
tighten hex nuts. 9. Replace terminal block access cover. 3-wire connection: Direct Wire Use this method only if local codes permit connecting ground conductor to neutral supply wire. 1. Pull the wires through the conduit on cord/conduit plate on bottom of range - Whirlpool WFE366LVT | Installation Instructions - Page 12
: Use a wrench or pliers to adjust leveling legs up or down until the range is level. Push range back into position. Check that rear leveling leg is engaged in anti-tip bracket. NOTE: Range must be level for satisfactory baking performance. 4. Replace the storage drawer (on some models). A. Drawer - Whirlpool WFE366LVT | Installation Instructions - Page 13
and oven. See the Use and Care Guide for specific instruction on range operation. If range does not operate, check the following: ■ Household fuse is intact and tight; or circuit breaker has not tripped. ■ Range is plugged into an outlet. ■ Electrical supply is connected. ■ See "Troubleshooting" in - Whirlpool WFE366LVT | Installation Instructions - Page 14
-tip bracket is installed: ■ Look for the anti-tip bracket securely attached to floor. ■ Slide range back so rear range foot is under anti-tip bracket. Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or - Whirlpool WFE366LVT | Installation Instructions - Page 15
Left edge ANTI-TIP BRACKET TEMPLATE Cut on dotted lines and place the left edge against the left side cabinet and the top edge against the rear wall. Top edge 15 - Whirlpool WFE366LVT | Installation Instructions - Page 16
W10252706B © 2009. All rights reserved. 9/09 Printed in U.S.A.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
 |
 |
INSTALLATION INSTRUCTIONS
30" (76 CM) FREESTANDING ELECTRIC RANGES
Table of Contents
RANGE SAFETY
...................................................................................
2
INSTALLATION REQUIREMENTS
......................................................
3
Tools and Parts
..................................................................................
3
Location Requirements
......................................................................
3
Electrical Requirements - U.S.A. Only
...............................................
4
INSTALLATION INSTRUCTIONS
........................................................
6
Unpack Range
....................................................................................
6
Install Anti-Tip Bracket
.......................................................................
6
Electrical Connection - U.S.A. Only
...................................................
7
Verify Anti-Tip Bracket Location
......................................................
12
Level Range
......................................................................................
12
Storage Drawer
................................................................................
12
Complete Installation
.......................................................................
13
Moving the Range
............................................................................
14
ANTI-TIP BRACKET TEMPLATE
.....................................................
15
IMPORTANT:
Save for local electrical inspector's use.
W10252706B