Whirlpool WFW3090J Dimension Guide
Whirlpool WFW3090J Manual
 |
View all Whirlpool WFW3090J manuals
Add to My Manuals
Save this manual to your list of manuals |
Whirlpool WFW3090J manual content summary:
- Whirlpool WFW3090J | Dimension Guide - Page 1
to reduce noise transfer. If a closet door or louvered door is installed, top and bottom air openings in door are required. Recessed area or closet installation (stacked washer and dryer): 0"/1" (0 mm/25 mm) 04""/*1†" (0 m(1m02/2m5mm)m) 3" (76 mm) 683⁄4" Min. (1764563/4m" m) (619617⁄20" mMmax - Whirlpool WFW3090J | Dimension Guide - Page 2
least 24" (60 cm) above floor; install no higher than 49" (125 cm) from bottom of washer. Floor drain system Floor drain system requires a Siphon Break Kit (Part Number 285834), 2 Connector Kits (Part Number 285835), and an Extension Drain Hose (Part Number 285863) that may be purchased separately
-
1 -
2
 |
 |
PRODUCT MODEL NUMBERS
W10856086B
1/2017
WFW3090G, WFW5090G
Washer
Location Requirements
Proper installation is your responsibility.
You will need:
n
A grounded electrical outlet located within 5.4 ft (1.7 m)
of power cord on back of washer.
n
Water faucet located within 4 ft (1.2 m) of water fill valve on washer,
and water pressure of 20–100 psi (137.9–689.6 kPa).
n
A level floor with maximum slope of 1" (25 mm) under entire washer.
Installing on carpet or surfaces with foam backing is
not recommended.
n
Floor must support washer’s total weight (with water and load)
of 400
lbs (180 kgs).
IMPORTANT:
Do not install, store, or operate washer where it will be
exposed to weather or in temperatures below 32°F (0°C). Water remaining
in washer after use may cause damage in
low temperatures. See “Washer Maintenance” for winterizing information.
1"
(25 mm)
1"
(25 mm)
39" min.
(990 mm)
Custom under counter installation:
Custom cabinet installation:
All dimensions show recommended spacing allowed, except for closet
door ventilation openings which are the minimum required.
For each arrangement, consider allowing more space for ease of installa-
tion and servicing, and spacing for companion appliances and clearances
for walls, doors, and floor moldings.
Recessed area or closet installation
(stacked washer and dryer):
†
External exhaust elbow requires additional space.
*
†
24"
(610 mm)
33
1
⁄
4
" Min.
(845 mm)
33
3
⁄
4
" Max.
(857 mm)
*2.3 cu. ft. models: 42
15
⁄16" (1091 mm)
1.9 cu. ft. models: 41
5
⁄8" (1057 mm)
†
2.3 cu. ft. models: 25
1
⁄8" (638 mm)
1.9 cu. ft. models: 24" (610 mm)
1"
(25 mm)
4"
(102 mm)
1"
(25 mm)
*Recommended
spacing. Minimum
0" (0 mm)
*
*
1"
(25 mm)
24 in.
2
(155 cm
2
)
48 in.
2
(310 cm
2
)
3"
(76 mm)
3"
(76 mm)
0"/1"
(0 mm/25 mm)
(0 mm/25 mm)
68
3
⁄
4
" Min.
(1746 mm)
69
1
⁄
2
" Max.
(1765 mm)
*Recommended
spacing. Minimum
0" (0 mm)
1"*
(25 mm)
1"*
(25 mm)
4"
*
†
(102 mm)
*
Space must be large enough to allow door to fully open.
Add spacing of 1" (25 mm) on all sides of washer to reduce
noise transfer. If a closet door or louvered door is installed,
top and bottom air openings in door are required.