Whirlpool WFW8300SW Use and Care Guide - Page 9

Route the Drain Hose, Secure the Drain Hose

Get Whirlpool WFW8300SW - Duet Sport Washer PDF manuals and user guides
UPC - 883049008417
View all Whirlpool WFW8300SW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Connect the inlet hoses to the washer H C Laundry tub drain or standpipe drain Connect the drain hose form to the corrugated drain hose. H. Hot water inlet C. Cold water inlet 1. Attach the hot water hose to the washer's hot (H) water inlet valve. Screw on coupling by hand until it is seated on the washer. 2. Attach the cold water hose to the washer's cold (C) water faucet. Screw on coupling by hand until it is seated on the washer. 3. Using pliers, tighten the couplings with an additional two-thirds turn. NOTE: Do not overtighten. Damage to the coupling can result. 4. Turn on the water faucets completely and check for leaks. NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record hose installation or replacement dates on the hoses for future reference. Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found. Route the Drain Hose Proper routing of the drain hose protects your floors from damage due to water leakage. Read and follow these instructions. Remove drain hose from the washer Gently pull the corrugated drain hose from the shipping clips. A B A. Snap either end of the drain hose form to the drain hose at the point where the corrugation begins. B. Bend drain hose over drain hose form and snap into place. To keep drain water from going back into the washer: s Do not straighten the drain hose, and do not force excess drain hose into standpipe. Hose should be secure, but loose enough to provide a gap for air. s Do not lay excess hose on the bottom of the laundry tub. Floor drain You may need additional parts. See Floor drain under "Tools and Parts." Secure the Drain Hose 1. Drape the power cord over the washer top. 2. Move the washer to its final location. 3. Place the drain hose in the laundry tub or standpipe as shown. See illustrations A and B. A B C 4. If the washer faucets and the drain standpipe are recessed, put the hooked end of the drain hose in the standpipe as shown. See illustration C. NOTES: s Do not force excess drain hose back into the rear of the washer. s To avoid siphoning, do not seal the drain hose into the standpipe. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
9
Connect the inlet hoses to the washer
1.
Attach the hot water hose to the washer
’
s hot (H) water inlet
valve. Screw on coupling by hand until it is seated on the
washer.
2.
Attach the cold water hose to the washer
’
s cold (C) water
faucet. Screw on coupling by hand until it is seated on the
washer.
3.
Using pliers, tighten the couplings with an additional
two-thirds turn.
NOTE:
Do not overtighten. Damage to the coupling can
result.
4.
Turn on the water faucets completely and check for leaks.
NOTE:
Replace inlet hoses after 5 years of use to reduce the
risk of hose failure. Record hose installation or replacement
dates on the hoses for future reference.
Periodically inspect and replace hoses if bulges, kinks, cuts,
wear, or leaks are found.
Route the Drain Hose
Proper routing of the drain hose protects your floors from
damage due to water leakage. Read and follow these
instructions.
Remove drain hose from the washer
Gently pull the corrugated drain hose from the shipping clips.
Laundry tub drain or standpipe drain
Connect the drain hose form to the corrugated drain hose.
To keep drain water from going back into the washer:
■
Do not straighten the drain hose, and do not force excess
drain hose into standpipe. Hose should be secure, but loose
enough to provide a gap for air.
■
Do not lay excess hose on the bottom of the laundry tub.
Floor drain
You may need additional parts. See Floor drain under
“
Tools and
Parts.
”
Secure the Drain Hose
1.
Drape the power cord over the washer top.
2.
Move the washer to its final location.
3.
Place the drain hose in the laundry tub or standpipe as
shown. See illustrations A and B.
4.
If the washer faucets and the drain standpipe are recessed,
put the hooked end of the drain hose in the standpipe as
shown. See illustration C.
NOTES:
■
Do not force excess drain hose back into the rear of the
washer.
■
To avoid siphoning, do not seal the drain hose into the
standpipe.
H. Hot water inlet
C. Cold water inlet
H
C
A. Snap either end of the drain hose form to the drain hose at
the point where the corrugation begins.
B. Bend drain hose over drain hose form and snap into place.
A
B
A
B
C