Whirlpool WGD96HEAC Dimension Guide

Whirlpool WGD96HEAC Manual

Get Whirlpool WGD96HEAC PDF manuals and user guides View all Whirlpool WGD96HEAC manuals
Add to My Manuals
Save this manual to your list of manuals

Whirlpool WGD96HEAC manual content summary:

  • Whirlpool WGD96HEAC | Dimension Guide - Page 1
    mm) Recommended installation clearances (dryer only): 53/4"* (146 mm) Vent Water inlet (Steam Models Only) servicing; spacing for companion appliances and clearances for walls, doors, and floor moldings. Space must be large enough to allow door to fully open. Add spacing on all sides of dryer
  • Whirlpool WGD96HEAC | Dimension Guide - Page 2
    larger tubing should be used. Pipe-joint compounds resistant to the action of L.P. gas must be used. An individual manual shutoff valve must be installed within 6 ft (1.8 m) of the dryer in accordance with the National Fuel Gas Code ANSI Z223.1. ELECTRICAL REQUIREMENTS A 120-volt, 60 Hz, AC-only, 15
  • 1
  • 2
Gas Dryer
PRODUCT MODEL NUMBERS
W10508900B
09/2012
WGD94HEA, WGD96HEA
27"
(686 mm)
3
/
4
"*
(18 mm)
38
1
/
8
"
(968 mm)
Back view:
6
1
/
4
"
(159 mm)
29
7
/
8
"*
(759 mm)
3
1
/
2
"*
(89 mm)
5
3
/
4
"*
(146 mm)
6
1
/
8
"*
(156 mm)
14
3
/
8
"
(365 mm)
25
3
/
4
"
(654 mm)
3
/
4
"*
(18 mm)
NOTE:
Most installations require a minimum of 5" (127 mm) clearance behind
dryer for exhaust vent with elbow. See “Venting Requirements”.
* Approx. measurement
Side view:
Front view:
DRYER DIMENSIONS
Gas
Water inlet
(Steam Models Only)
Vent
18" min.
(457 mm)
1"
(25 mm)
5"
(127 mm)
24 in.
2
min.
(155 cm
2
)
48 in.
2
min.
(310 cm
2
)
3"
(76 mm)
3"
(76 mm)
1"
(25 mm)
Recommended installation clearances (dryer only):
Installation spacing for recessed area or closet installation
All dimensions show recommended and minimum spacing allowed.
■
Additional spacing should be considered for ease of
installation and servicing.
■
Additional clearances might be required for wall, door, floor moldings, dryer
venting, and gas line.
■
Additional spacing should be considered on all sides
of the dryer to reduce noise transfer.
■
For closet installation, with a door, minimum ventilation openings in the top and
bottom of the door are required. Louvered doors with equivalent ventilitation
openings are acceptable.
■
Companion appliance spacing should also be considered.
Installation Clearances
For each arrangement, consider allowing more space for ease of installation
and servicing; spacing for companion appliances and clearances for walls,
doors, and floor moldings. Space must be large enough to allow door to fully
open. Add spacing on all sides of dryer to reduce noise transfer. If a closet door
or louvered door is installed, top and bottom air openings in door are required.
Check code requirements. Some codes limit, or do not permit, installation of
the dryer in garages, closets, mobile homes, or sleeping quarters. Contact your
local building inspector.
NOTE:
No other fuel-burning appliance can be installed in the same closet as
a dryer.
*
0" (0 mm) spacing is allowed.
* Approx. measurement
* Approx. measurement