Whirlpool WMH31017FW Installation Guide
Whirlpool WMH31017FW Manual
 |
View all Whirlpool WMH31017FW manuals
Add to My Manuals
Save this manual to your list of manuals |
Whirlpool WMH31017FW manual content summary:
- Whirlpool WMH31017FW | Installation Guide - Page 1
of your particular model may differ slightly from the illustration in these installation instructions. Table of Contents MICROWAVE HOOD COMBINATION SAFETY 1 INSTALLATION REQUIREMENTS 2 Tools and Parts 2 Remove Cardboard Template 2 Location Requirements 2 Product Dimensions 3 Electrical - Whirlpool WMH31017FW | Installation Guide - Page 2
to back of microwave oven) ■■ Cardboard template (part of packaging) ■■ Aluminum grease filters ■■ Charcoal filters (Depending on model, charcoal filters may not be included. See User Instructions.) NOTE: Depending on model, aluminum grease filter and charcoal filter may be combined. Materials - Whirlpool WMH31017FW | Installation Guide - Page 3
) installation height. Exact dimensions may vary depending on type of range/ cooktop below. Product Dimensions 17¹⁄₈" (43.5 cm) (0.5 cm) 16¹⁄₄" (41.3 cm) (42.15U6c³p⁄m₄t"o)* 29⁷⁄₈" (76.0 cm) *Overall depth of product will vary slightly depending on door design. GROUNDING INSTRUCTIONS I For - Whirlpool WMH31017FW | Installation Guide - Page 4
INSTALLATION INSTRUCTIONS Remove Mounting Plate Depending on your model, the mounting plate may be in the foam packaging, or it may be attached to the back of the microwave oven. NOTE: To avoid possible damage to the work surface, cover the work surface. 1. Remove any remaining contents from the - Whirlpool WMH31017FW | Installation Guide - Page 5
. Make sure damper plate tabs are inserted into the slots in the top of the microwave oven. A B C 6. Reattach blower motor to back of microwave oven with 2 screws removed in Step 3 of "Wall Venting Installation Only." Securely tighten screws. NOTE: If blower motor is not correctly oriented, the - Whirlpool WMH31017FW | Installation Guide - Page 6
studs exist within the cabinet opening, do not install the microwave oven. See illustrations in "Possible Wall Stud Configurations holes (on mounting plate) B. Cabinet opening vertical centerline C. Wall stud centerlines D. Holes for lag screws E. Support tabs F. Mounting plate center markers 6 - Whirlpool WMH31017FW | Installation Guide - Page 7
Rear Wall The microwave oven must be installed on a minimum is damaged or unusable, measure and mark the wall with the dimensions described in Step 4. D A C B A. Rear wall B. ¹⁄₈" (35.9 cm) from the centerline. 5. With the support tabs facing forward (see illustrations in "Locate Wall Stud(s)" - Whirlpool WMH31017FW | Installation Guide - Page 8
1 wall stud as well as at both ends. 1. With the support tabs of the mounting plate facing forward, insert 3/16-24 x guides. ■■ If the wall behind the microwave oven (as installed) has a partial wall covering (for example, tile backsplash), be sure the "Rear Wall" arrows align to the thickest part - Whirlpool WMH31017FW | Installation Guide - Page 9
NOTE: If upper cabinet is metal, the supply cord bushing needs to be installed around the supply cord hole as shown. B A A. Metal cabinet B. Power 2. Make sure the microwave oven door is closed and taped shut. 3. Using 2 or more people, lift microwave oven and hang it on support tabs at the bottom - Whirlpool WMH31017FW | Installation Guide - Page 10
cabinet bottom and the microwave oven. A 2. Connect vent to damper assembly. A B A. Vent B. Damper assembly (under vent) Complete Installation 1. Install filters. Refer to the User Instructions for filter placement. WARNING A. Bolts For Roof Venting Installation Only 1. Insert damper assembly - Whirlpool WMH31017FW | Installation Guide - Page 11
This section is intended for architectural designer and builder/ contractor reference only. NOTES: ■■ Vent materials needed for installation are not provided with microwave hood combination. ■■ We do not recommend using a flexible metal vent. ■■ To avoid possible product damage, be sure - Whirlpool WMH31017FW | Installation Guide - Page 12
of the installation hardware needs to be replaced, call us at our toll free number listed in the User Guide. Following is a list of available replacement parts. You will need your model number located on the front facing of the microwave oven opening, behind the door. ■■ Damper Assembly ■■ Mounting
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
 |
 |
MICROWAVE HOOD COMBINATION
INSTALLATION INSTRUCTIONS
This product is suitable for use above electric or gas cooking products up to and including 36" (91.4 cm) wide. See “Installation
Requirements” section for further notes.
These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration
in these installation instructions.
MICROWAVE HOOD COMBINATION SAFETY
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
MICROWAVE HOOD COMBINATION SAFETY
............................
1
INSTALLATION REQUIREMENTS
.................................................
2
Tools and Parts
.............................................................................
2
Remove Cardboard Template
......................................................
2
Location Requirements
................................................................
2
Product Dimensions
.....................................................................
3
Electrical Requirements
...............................................................
3
INSTALLATION INSTRUCTIONS
...................................................
4
Remove Mounting Plate
...............................................................
4
Rotate Blower Motor
....................................................................
4
Locate Wall Stud(s)
......................................................................
6
Mark Rear Wall
.............................................................................
7
Drill Holes in Rear Wall
.................................................................
7
Attach Mounting Plate to Wall
.....................................................
8
Prepare Upper Cabinet
................................................................
8
Install Damper Assembly
.............................................................
9
Install the Microwave Oven
..........................................................
9
Complete Installation
.................................................................
10
VENTING DESIGN SPECIFICATIONS
.........................................
11
ASSISTANCE
................................................................................
12
Replacement Parts
.....................................................................
12
Accessories
................................................................................
12
Table of Contents
W10823831A