Whirlpool WMHA9019HV Installation Instructions
Whirlpool WMHA9019HV Manual
 |
View all Whirlpool WMHA9019HV manuals
Add to My Manuals
Save this manual to your list of manuals |
Whirlpool WMHA9019HV manual content summary:
- Whirlpool WMHA9019HV | Installation Instructions - Page 1
particular model may differ slightly from the illustration in these installation instructions. Table of Contents MICROWAVE HOOD COMBINATION SAFETY 1 INSTALLATION REQUIREMENTS 2 Tools and Parts 2 Location Requirements 2 Product Dimensions 3 Electrical Requirements 3 INSTALLATION INSTRUCTIONS - Whirlpool WMHA9019HV | Installation Instructions - Page 2
filters (Depending on model, charcoal filters may not be included. See User Instructions.) Location Requirements Check the opening where the microwave oven will be installed. The location must provide: ■■ Minimum installation dimensions. See the "Installation Dimensions" illustration. ■■ Minimum - Whirlpool WMHA9019HV | Installation Instructions - Page 3
be purchased from Whirlpool. 12" DEEPER 14" 14" DEEPER 15" I bar mounting plate Bump out mounting bracket Product Dimensions Observe all governing short, have a qualified electrician or serviceman install an outlet near the microwave oven. SAVE THESE INSTRUCTIONS 17¹⁄₈" (43.5 cm 0.5 cm) 16 - Whirlpool WMHA9019HV | Installation Instructions - Page 4
INSTALLATION INSTRUCTIONS Remove Mounting Plate Depending on your model, the mounting plate may be in the foam packaging, or it may be attached to the back of the microwave oven. NOTE: To avoid possible damage to the work surface, cover the work surface. 1. Remove any remaining contents from the - Whirlpool WMHA9019HV | Installation Instructions - Page 5
snip out the rectangular damper vent covers at the perforations. 10. Reattach the 2 blower screws into the recessed holes in the back of the microwave. A B A. Diagonal wire cutting pliers B. Rectangular damper vent cover 7. Hold the blower motor wire, put the wire through the blower motor bridge - Whirlpool WMHA9019HV | Installation Instructions - Page 6
Venting Installation Only." 6. Using diagonal wire cutting pliers, gently snip out the rectangular vent covers on the damper plate at the perforations. A 8. Reconnect the blower motor wire into the connector. 9. Reattach the 2 blower screws into the recessed holes in the back of the microwave. 10 - Whirlpool WMHA9019HV | Installation Instructions - Page 7
for lag screws E. Support tabs F. Mounting plate center markers Mark Rear Wall The microwave oven must be installed on a minimum of the wall template is damaged or unusable, measure and mark the wall with the dimensions described in Step 4. A A A. Centerline 2. Align the center markers on the - Whirlpool WMHA9019HV | Installation Instructions - Page 8
be 141⁄8" (35.96 cm) from the centerline. 5. With the support tabs facing forward (see illustrations in the "Locate Wall Stud(s)" section), 1 and 2 in "Possible Wall Stud Configurations" in the"Locate Wall Stud(s)" section. Installation for Wall Stud at One End Hole (Figure 3) 1. Drill a 3/16" (5 mm - Whirlpool WMHA9019HV | Installation Instructions - Page 9
lag screws and bolts. Wall Stud at One End Hole (Figure 3) 1. With the support tabs of the mounting plate facing forward, insert a 3/16-24 x 3" (7.6 cm . The template has trim lines to use as guides. ■■ If the wall behind the microwave oven (as installed) has a partial wall covering (for example, - Whirlpool WMHA9019HV | Installation Instructions - Page 10
C. Damper blade D. #6 x 3/8" Sheet metal screw (2) 3. Secure damper assembly with 2 #6 x 3/8" sheet metal screws. Install the Microwave Oven WARNING Excessive Weight Hazard Use two or more people to move and install microwave oven. Failure to do so can result in back or other injury. IMPORTANT: The - Whirlpool WMHA9019HV | Installation Instructions - Page 11
vent fan. 5. If the microwave oven does not operate: ■■ problem continues, call an electrician. ■■ Check that the power supply cord is plugged into a grounded 3 prong outlet. ■■ See the User Instructions for troubleshooting information. The installation is now complete. Save Installation Instructions - Whirlpool WMHA9019HV | Installation Instructions - Page 12
This section is intended for architectural designer and builder/ contractor reference only. NOTES: ■■ Vent materials needed for installation are not provided with microwave hood combination. ■■ We do not recommend using a flexible metal vent. ■■ To avoid possible product damage, be sure - Whirlpool WMHA9019HV | Installation Instructions - Page 13
to round transition piece must be used. In addition, a rectangular 3" (7.6 cm) extension vent between the damper assembly and rectangular to round transition piece must be installed to keep the damper from sticking. 13 - Whirlpool WMHA9019HV | Installation Instructions - Page 14
Parts If any of the installation hardware needs to be replaced, call us at our toll-free number listed in the User Guide. Following is a list of available replacement parts. You will need your model and serial numbers located on the front facing of the microwave oven opening, behind the door - Whirlpool WMHA9019HV | Installation Instructions - Page 15
Notes 15 - Whirlpool WMHA9019HV | Installation Instructions - Page 16
W11380664A SP PN W11380668 ©2019 All rights reserved. 11/19
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
 |
 |
MICROWAVE HOOD COMBINATION
INSTALLATION INSTRUCTIONS
This product is suitable for use above electric or gas cooking products up to and including 36" (91.4 cm) wide. See the “Installation
Requirements” section for further notes.
These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration
in these installation instructions.
Table of Contents
MICROWAVE HOOD COMBINATION SAFETY
W11380664A
MICROWAVE HOOD COMBINATION SAFETY
..................................
1
INSTALLATION REQUIREMENTS
.......................................................
2
Tools and Parts
..................................................................................
2
Location Requirements
......................................................................
2
Product Dimensions
...........................................................................
3
Electrical Requirements
.....................................................................
3
INSTALLATION INSTRUCTIONS
.........................................................
4
Remove Mounting Plate
....................................................................
4
Rotate Blower Motor
..........................................................................
4
Locate Wall Stud(s)
............................................................................
7
Mark Rear Wall
...................................................................................
7
Drill Holes in Rear Wall
.......................................................................
8
Attach Mounting Plate to Wall
...........................................................
8
Prepare Upper Cabinet
......................................................................
9
Install Damper Assembly
.................................................................
10
Install the Microwave Oven
..............................................................
10
Complete Installation
.......................................................................
11
VENTING DESIGN SPECIFICATIONS
...............................................
12
ASSISTANCE
......................................................................................
14
Replacement Parts
..........................................................................
14
Accessories.
.....................................................................................
14