Whirlpool WRB322DMB Instruction Sheet
Whirlpool WRB322DMB Manual
 |
View all Whirlpool WRB322DMB manuals
Add to My Manuals
Save this manual to your list of manuals |
Whirlpool WRB322DMB manual content summary:
- Whirlpool WRB322DMB | Instruction Sheet - Page 1
Instruction Sheet for Ice Maker kit WARNING Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. Kit Contains: 2 Module Covers 2 Wire Harnesses 1 Ice Maker (with no Harness) 1 Shut Off - Whirlpool WRB322DMB | Instruction Sheet - Page 2
assembly. See Figure 8. clip thermal fuse Wire Harness connector figure 8 IMPORTANT: For Type A module continue on to next step, for Type B module replace ice maker with new one in kit, using existing harness and skip ahead to step 17. See Figure 6. 11. Remove thermistor from tab on impinger - Whirlpool WRB322DMB | Instruction Sheet - Page 3
to release the solinoid assembly. See Figure 23. tabs figure 18 IMPORTANT: For Type A module continue on to next step, for Type B module replace ice maker with new one in kit, using existing harness and skip ahead to step 31. See Figure 16. 23. Remove fan module using screwdriver. Disconnect fan - Whirlpool WRB322DMB | Instruction Sheet - Page 4
service procedures. figure 25 33. Install shut off arm assembly onto new ice maker assembly as shown. NOTE: Push one end of the shut off arm assembly into module and guide other end into upper hole next to fill cup. See Figure 26. module UPPER Hole shut off arm assembly figure 26 © Whirlpool - Whirlpool WRB322DMB | Instruction Sheet - Page 5
la source de courant électrique avant l'entretien. Replacer pièces et panneaux avant de faire la remise en marche. Le non-respect de ces instructions peut causer un décès ou un choc électrique. Contenu de la trousse : 2 couvercles de module 2 faisceaux de câblage 1 machine à glaçons (sans faisceau - Whirlpool WRB322DMB | Instruction Sheet - Page 6
9. Inverser la machine à glaçons et enlever trois vis situées au-dessous du déflecteur d'air pour dégager la machine à glaçons. Conserver les vis à part. Voir la Figure 7. (3) vis 15. Tirer l'œillet et le faisceau dans le boîtier du ventilateur, puis l'autre œillet à l'extérieur du boîtier du - Whirlpool WRB322DMB | Instruction Sheet - Page 7
MODÈLES À 25 PI2 SEULEMENT 20. Utiliser un tournevis à lame plate pour enlever le couvercle du module de la machine à glaçons. Enlever le connecteur H-Tap. Jeter le vieux couvercle de module. Voir la Figure 16. REMARQUE : Un module de type A ou B peut être présent. type A type b vis CONNECTEUR - Whirlpool WRB322DMB | Instruction Sheet - Page 8
pas utiliser un adaptateur. Ne pas utiliser un câble de rallonge. Le non-respect de ces instructions peut causer un décès, un incendie ou un choc électrique. 40. Brancher le réfrigérateur DE COMMANDE AVEC EXTENSION figure 26 © Whirlpool Corporation 2016 (Tous droits réservés) - 8 - W10885624 A
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
 |
 |
Instruction Sheet W10885624
Rev A
8/16
Instruction Sheet
for Ice Maker kit
— 1 —
Kit Contains:
1.
Unplug refrigerator or disconnect power.
2.
Remove ice bin by depressing push button on side of ice
bin cover. Pull ice bin upward and slide out of ice box
compartment. See
Figure 1
.
2
Module Covers
2
Wire Harnesses
1
Ice Maker (with no Harness)
1
Shut Off Arm (with no Extension)
1
Instruction Sheet
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Failure to do so can result in death
or electrical shock.
Replace all parts and panels before
operating.
(continued)
FIGURE 1
PUSH
BUTTON
FIGURE 2
TAB
HARNESS
COVER
5.
Release tab on left front of ice maker and slide ice maker
auger assembly forward and out. See
Figure 4.
IMPORTANT:
Be sure to use the correct harness and module
cover for your unit. See
Figure 5.
6.
If you are working on a 22 cubic foot model, proceed to next
step. If you are working on a 25 cubic foot model, proceed
to step 20.
3.
Depress the tab holding the ice maker wire harness cover
and slide cover forward. See
Figure 2
.
4.
Disconnect harness. See
Figure 3
.
FIGURE 4
FIGURE 3
HARNESS
CONNECTOR
FIGURE 5
25 CUFT
22 CUFT
SWITCH
ICE MAKER MODULE COVER
22 CUFT
25 CUFT
SWITCH
CONNECTORS
THERMISTOR
THERMISTOR
GROMMET
22 CUBIC FOOT MODELS ONLY
7.
Use a straight blade screwdriver to remove the ice maker
module cover. Remove H-Tap connector. See
Figure 6.
NOTE:
You may see a Type A or a Type B module.
SCREW
H-TAP
CONNECTOR
TYPE B
TYPE A
FIGURE 6
8.
Disconnect connectors to switch in old module cover.
Remove switch from old module cover, set aside. Discard
old module cover.