Whirlpool WVW57UC0F Dimension Guide
Whirlpool WVW57UC0F Manual
 |
View all Whirlpool WVW57UC0F manuals
Add to My Manuals
Save this manual to your list of manuals |
Whirlpool WVW57UC0F manual content summary:
- Whirlpool WVW57UC0F | Dimension Guide - Page 1
Wall-Mount Canopy Range Hood PRODUCT MODEL NUMBERS WVW57UC0F WVW57UC6F ELECTRICAL REQUIREMENTS A 120-volt, 60-Hz., AC the vent should be uniform. Because Whirlpool Corporation includes a continues commitment to complete details, see Installation Instructions packed with product. Specifications - Whirlpool WVW57UC0F | Dimension Guide - Page 2
deflector). To order, see the "Assistance or Service" section. Roof Venting Wall Venting Non-Vented length is 35 ft (10.7 m). Because Whirlpool Corporation includes a continues commitment to improve our complete details, see Installation Instructions packed with product. Specifications
-
1 -
2
 |
 |
PRODUCT MODEL NUMBERS
Because Whirlpool Corporation includes a continues commitment to improve our
products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. W10836385B
05/09/2016
Page 1 of 2
WVW57UC6F
WVW57UC0F
30" (76.2 cm) and 36" (91.4 cm) Wall-Mount
Canopy Range Hood
PRODUCT DIMENSIONS
* For non-vented (recirculating) installations
** For vented installations.
10
⁵/₈
" (26.9 cm)
13
¹/₁₆
" (33.2 cm)
4
⁷/₈
" (12.3 cm)
5
⁷/₈
" (15.0 cm)
*29" (73.7 cm) min.
46
⁹/₁₆
" (118.3 cm) max.
**29" (73.7 cm) min.
42¾" (108.6 cm) max.
19
¹/₁₆
"
(48.5 cm)
15 ¹/₄
"
(38.7 cm)
2³/₈
"
(6.0 cm)
19
¹¹/₁₆
" (50.0 cm)
30" (76.2 cm)
36" (91.4 cm)
VENTING REQUIREMENTS
■
Vent system must terminate to the outdoors except for non-vented
(recirculating) installations.
■
Do not terminate the vent system in an attic or other enclosed area.
■
Do not use 4" (10.2 cm) laundry-type wall cap.
■
Use metal vent only. Rigid metal vent is recommended. Plastic or
metal foil vent is not recommended.
■
The length of vent system and number of elbows should be kept to a
minimum to provide efficient performance.
For the Most Efficient and Quiet Operation:
■
Use no more than three 90° elbows.
■
Make sure there is a minimum of 24" (61 cm) of straight vent between
the elbows if more than 1 elbow is used.
■
Do not install 2 elbows together.
■
Use clamps to seal all joints in the vent system.
■
The vent system must have a damper. If the roof or wall cap has a
damper, do not use the damper supplied with the range hood.
■
Use caulking to seal exterior wall or roof opening around the cap.
■
The size of the vent should be uniform.
CABINET DIMENSIONS
10" (25.4 cm) min.
13" (33.0 cm) max.
9¹/₂
" (24.1 cm)
2" (5.1 cm) min.
9" (22.9 cm) min.*
Centerline
Side
cabinet
Side
cabinet
Vent and power
supply cable
entry location
30" (76.2 cm) or
36" (91.4 cm)
“X”
bottom of
canopy
to cooking
surface
10" (25.4 cm) min.
13" (33.0 cm) max.
Cooking surface
17" (43.2 cm)*
* For non-vented (recirculating) installations
IMPORTANT:
Minimum distance “X”: 24" (61 cm) from electric cooking surface
Minimum distance “X”: 27" (68.6 cm) from gas cooking surface
Suggested maximum distance “X”: 36" (91.4 cm)
The chimneys can be adjusted for different ceiling heights. See the
following chart.
Vented Installations
Min. ceiling height
Max. ceiling height
Electric cooking surface
7' 5" (2.26 m)
9' 6" (2.9 m)
Gas cooking surface
7' 8" (2.34 m)
9' 6" (2.9 m)
Non-Vented (Recirculating) Installations
Min. ceiling height
Max. ceiling height
Electric cooking surface
7' 5" (2.26 m)
9' 10" (3 m)
Gas cooking surface
7' 8" (2.34 m)
9' 10" (3 m)
NOTE:
The range hood chimneys are adjustable and designed to
meet varying ceiling or soffit heights depending on the distance “X”
between the bottom of the range hood and the cooking surface. For
higher ceilings, a Stainless Steel Chimney Extension Kit Part Number
EXTKIT25FS is available from your dealer or an authorized parts
distributor. The chimney extension replaces the upper chimney shipped
with the range hood.
ELECTRICAL REQUIREMENTS
A 120-volt, 60-Hz., AC-only, 15-amp, fused electrical circuit is required.