Yamaha CLP-311 Owner's Manual - Page 23
Zusammenbau und Aufstellung, Keyboard Stand Assembly
View all Yamaha CLP-311 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 23 highlights
1 A B C D Bundled pedal cord inside Gebündeltes Pedalkabel Cordon de pédalier enroulé à l'intérieur Cable de pedales enrollado en el interior q AC power cord q Netzkabel q Cordon d'alimentation q Cable de alimentación de CA 6 x 35 mm round-head screws x 4 1 6 x 35 mm Halbrundschrauben x 4 1 Vis à tête ronde de 6 x 35 mm x 4 1 Tornillos de cabeza redonda de 6 x 35 mm x4 1 6 x 16 mm flat-head screws x 8 2 6 x 16 mm Senkschrauben x 8 2 Vis à tête plate de 6 x 16 mm x 8 2 Tornillos de cabeza plana de 6 x 16 mm x8 2 Keyboard Stand Assembly NOTE • We do not recommend attempting to assemble the Clavinova alone. The job can be easily accomplished, however, with only two people. • Use only the screws provided or replacements of exactly the specified size. Using screws of the wrong size can result in damage to the instrument. Z Open the box and remove all the parts. On opening the box you should find the parts shown in the illustration above. Check to make sure that all the required parts are provided. X Attach (C). the side panels (D) to the pedal box Before installing the pedal box, untie and straighten out the bundled cord attached to the bottom of the pedal box. Don't discard the vinyl tie, you'll need it later in step B. Place the pedal box on top of the wooden blocks attached to the side panels (D), and attach using the four 6 x 35 millimeter round-head screws 1 - two screws on each side. Make sure the pedals extend in the same direction as the feet. C Attach the els (D). center panel (B) to the side pan- The center panel (B) is installed between the side panels (D) with the brackets on each end toward the rear of the stand assembly. Place the square holes in the center-panel brackets over the lugs extending from the side panels, then slide down. Each side of the center panel is attached using two 6 x 16 flat-head screws 2. Zusammenbau und Aufstellung HINWEIS • Wir raten davon ab, das Clavinova alleine zusammenzubauen und aufzustellen. Zwei Personen können diese Arbeit jedoch problemlos ausführen. • Verwenden Sie ausschließlich die mitgelieferten Schrauben oder Ersatzschrauben identischer Größe. Die Verwendung von Schrauben mit abweichenden Maßen kann eine Beschädigung des Instruments zur Folge haben. Z Öffnen Sie den Teile heraus. Karton und nehmen Sie alle Im Karton sollten die oben abgebildeten Teile enthalten sein. Prüfen Sie zunächst bitte, ob alle Teile vollständig vorhanden sind. X Schrauben Sie den Pedalkasten Seitenwänden (D) fest. (C) an den Bevor Sie den Pedalkasten montieren, nehmen Sie zunächst das gebündelte Kabel aus dem Pedalkasten, entfernen den Kabelbinder und ziehen das Kabel dann gerade aus. Werfen Sie den Kabelbinder nicht wg, er wird in Schritt B wieder gebraucht. Setzen Sie den Pedalkasten auf die Holzklötze an den Seitenwänden (D), und schrauben Sie ihn dann mit den vier 6 x 35 mm Halbrundschrauben 1 fest (jeweils zwei Schrauben links und rechts). Achten Sie dabei darauf, daß die Pedale in dieselbe Rich- tung weisen wie die vorspringenden Teile der Füße. C Schrauben Sie die Rückwand den Seitenwände (D). (B) an die bei- Die Rückwand (B) wird mit den Winkelblechen an beiden Enden nach hinten weisend an den Seitenwänden (D) befestigt. Lassen Sie dabei die Führungsnasen an den Seitenwänden in die Schlitzbohrungen in den beiden Winkelblechen greifen, und drücken Sie die Rückwand dann nach unten. Sichern Sie die Rückwand dann mit jeweils zwei kurzen schwarzen Schrauben 2 an den Seitenwänden. i