Yamaha DM2000 Dm2000 Update V1.1

Yamaha DM2000 Manual

Get Yamaha DM2000 PDF manuals and user guides View all Yamaha DM2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Yamaha DM2000 manual content summary:

  • Yamaha DM2000 | Dm2000 Update V1.1 - Page 1
    remain the same. Bass Management for 3-1 & ST Monitor Matrixes Bass Management can now be used with the 3-1 and Stereo Out monitor matrixes. Previously, Bass Management could be used only with the 5.1 monitor matrix. The Bass Management function can be found on the Surround Monitor Setup page, which
  • Yamaha DM2000 | Dm2000 Update V1.1 - Page 2
    functions, and shuttle and scrub could be used to control an external DAW only when a Remote Layer was selected. With the new DAW CONTROL option, a DAW can be controlled regardless of which Layer is currently selected. The new MACHINE CONTROL and DAW CONTROL options have been added to the following
  • Yamaha DM2000 | Dm2000 Update V1.1 - Page 3
    ), the Dimmer is turned on or off. Solo to Studio Out With the new Solo Bus to Studio Out preference on the Preferences 1 page, which can be selected by using the DISPLAY ACCESS [SETUP] button, soloed channels can now be monitored through the STUDIO MONITOR OUT. User Defined Keys The following items
  • Yamaha DM2000 | Dm2000 Update V1.1 - Page 4
    M.D.G., PA·DMI Division, Yamaha Corporation © 2002 Yamaha Corporation
  • 1
  • 2
  • 3
  • 4
1
Yamaha DM2000 Update V1.1
This document explains the new and revised func-
tions for DM2000 Update 1.1.
Scene Memory & Input/Output Patch
Linking
Input Patch and Output Patch library memories can
be linked to Scene memories so that when a Scene is
recalled, the input and output patches are recalled as
well.
The PATCH LINK INPUT and OUTPUT parame-
ters can be found on the Scene Memory page shown
below, which is located by pressing the SCENE
MEMORY [DISPLAY] button.
Use the cursor buttons to select the PATCH LINK
INPUT and OUTPUT parameters, use the Parame-
ter wheel to select Input Patch and Output Patch
library memories, and press the [ENTER] button to
set. A dash (–) means that no patch memory is
selected.
When you store a Scene, the last recalled or stored
Input Patch and Output Patch library memories are
automatically linked to that Scene.
If the specified Input or Output Patch library mem-
ory contains no data, only the Scene is recalled, the
input and output patching will remain the same.
Bass Management for 3-1 & ST
Monitor Matrixes
Bass Management can now be used with the 3-1 and
Stereo Out monitor matrixes. Previously, Bass Man-
agement could be used only with the 5.1 monitor
matrix. The Bass Management function can be
found on the Surround Monitor Setup page, which
can be located by using the MONITOR [DISPLAY]
button when either the 3-1 or 5.1 Surround mode is
selected.
The following screen shots show the Bass Manage-
ment configurations for the 5.1, 3-1, and Stereo
monitor matrixes, with Bass Management turned on
and off.
In addition, the Monitor Matrix configurations have
changed as follows. (The 5.1 to 5.1 matrix is
unchanged.)
Note: When using the 3-1 monitor matrix, even with
film sources, use Bass Management presets 1 and 2
(presets 3 and 4 may not provide correct monitoring).
5.1 ON
3-1 ON
ST ON
5.1 OFF
3-1 OFF
ST OFF
3-1 to 3-1
3-1 to ST
5.1 to 5.1
5.1 to 3-1
5.1 to ST
E