Yamaha DSP-A2 Owner's Manual - Page 29

C. Main Sp, 1d. Lfe/bass Out, 1e. Sys. Setup, 1f. Main Level

Get Yamaha DSP-A2 PDF manuals and user guides View all Yamaha DSP-A2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

English PREPARATION 1C. MAIN SP Choices: LARGE/SMALL Preset position: LARGE LARGE: If your main speakers have a high ability for bass reproduction. In this position, full range signals present at the main channels are output from the main speakers. SMALL: If your main speakers do not have a high ability for bass reproduction. However, if your system does not include a subwoofer, do not select this position. In this position, low bass signals (below 90 Hz) at the main channels are output from the SUBWOOFER terminals (if the SW or BOTH position is selected on "1D. LFE/BASS OUT"). 1E. SYS. SETUP Choices: 7ch/5ch Preset position: 7ch 7ch: If your speaker system includes a pair of front effect speakers. 5ch: If your speaker system does not include a pair of front effect speakers. Sound signals at the left and right front effect channels are distributed to the left and right main channels respectively, and output from the main speakers. 1D. LFE/BASS OUT Choices: SW/MAIN/BOTH Preset position: SW MAIN: If your system does not include a subwoofer. In this position, full range signals present at the main channels, signals from the LFE channel and other low bass signals that are selected on "1A. CENTER SP" to "1C. MAIN SP" to be distributed from other channels are output from the main speakers. SW/BOTH: Select either the SW or BOTH position if your system includes a subwoofer. In either position, signals at LFE channel and other low bass signals that are selected on "1A. CENTER SP" to "1C. MAIN SP" to be distributed from other channels are output from the SUBWOOFER terminals. When the LARGE position is selected on "1C. MAIN SP", in the SW position, no signal is distributed from the main channels to the SUBWOOFER terminals, however in the BOTH position, low bass signals from the main channels are output to both of the main speakers and the SUBWOOFER terminals. 1F. MAIN LEVEL Choices: Normal/-10dB Preset position: Normal Normal: Normally, select this position. -10dB: If the volume levels to the center, rear and/or front effect speakers are lower than the level to the main speakers even though they are adjusted to maximum. The volume level to the main speakers are decreased by 10 dB, so you can adjust the speaker output level balance properly. Note The settings of "1A" to "1E" have no effect on the signals input to the EXTERNAL DECODER INPUT terminals on the rear of this unit. 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
27
English
1C. MAIN SP
Choices: LARGE/SMALL
Preset position: LARGE
LARGE
:
If your main speakers have a high ability for bass
reproduction.
In this position, full range signals present at the main
channels are output from the main speakers.
SMALL
:
If your main speakers do not have a high ability for
bass reproduction. However, if your system does not
include a subwoofer, do not select this position.
In this position, low bass signals (below 90 Hz) at the
main channels are output from the SUBWOOFER
terminals (if the SW or BOTH position is selected on
“1D. LFE/BASS OUT”).
1D. LFE/BASS OUT
Choices: SW/MAIN/BOTH
Preset position: SW
MAIN
:
If your system does not include a subwoofer.
In this position, full range signals present at the main
channels, signals from the LFE channel and other
low bass signals that are selected on “1A. CENTER
SP” to “1C. MAIN SP” to be distributed from other
channels are output from the main speakers.
SW/BOTH
:
Select either the SW or BOTH position if your system
includes a subwoofer.
In either position, signals at LFE channel and other
low bass signals that are selected on “1A. CENTER
SP” to “1C. MAIN SP” to be distributed from other
channels are output from the SUBWOOFER
terminals.
When the LARGE position is selected on “1C. MAIN
SP”, in the
SW
position, no signal is distributed from
the main channels to the SUBWOOFER terminals,
however in the
BOTH
position, low bass signals from
the main channels are output to both of the main
speakers and the SUBWOOFER terminals.
1E. SYS. SETUP
Choices: 7ch/5ch
Preset position: 7ch
7ch
:
If your speaker system includes a pair of front effect
speakers.
5ch
:
If your speaker system does not include a pair of
front effect speakers.
Sound signals at the left and right front effect
channels are distributed to the left and right main
channels respectively, and output from the main
speakers.
1F. MAIN LEVEL
Choices: Normal/–10dB
Preset position: Normal
Normal
:
Normally, select this position.
–10dB
:
If the volume levels to the center, rear and/or front
effect speakers are lower than the level to the main
speakers even though they are adjusted to
maximum.
The volume level to the main speakers are
decreased by 10 dB, so you can adjust the speaker
output level balance properly.
PREPARATION
Note
The settings of “1A” to “1E” have no effect on the signals input
to the EXTERNAL DECODER INPUT terminals on the rear of
this unit.