Yamaha DSP-A2 Owner's Manual - Page 36

When you finish using this unit, To select the source connected to this unit's

Get Yamaha DSP-A2 PDF manuals and user guides View all Yamaha DSP-A2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

BASIC OPERATION When you finish using this unit Press the STANDBY/ON switch on the front panel or the STANDBY key on the remote controller to enter the standby mode. Front panel STANDBY/ON Remote control or STANDBY To select the source connected to this unit's EXTERNAL DECODER INPUT terminals as the input source. Press the EXT. DECODER button. "EXT. DECODER IN" will appear on the display. Front panel EXT. DECODER Remote control EXT. DEC. or Notes on input source selection q Note that selecting an input source means that the source which is connected to the corresponding input terminals on the rear panel is selected. * To select the source connected to the VIDEO AUX terminals on the front panel, select "V-AUX". q The setting of the EXT. DECODER button cannot be canceled by selecting another input source. To cancel it, press the EXT. DECODER button again so that "EXT. DECODER IN" goes off from the display. q If you select a video input source without canceling the setting of the EXT. DECODER button, you will see the picture of the video input source and hear the sound of the source selected by the EXT. DECODER button. q If a different audio source is selected with the input selector keys on the remote controller while enjoying a video source, the sound from the newly selected audio source is heard, but the picture from the video source can still be seen. q When you select an input source, the DSP program (or the state of no DSP program is used) which was used when the same input source was last selected will be automatically recalled. q If a nonstandardized source is played back, or the unit playing back a source is not operating correctly, "INPUT DATA ERR" appears on the display. Note The input source selected in this way has priority over any other input source already selected. To select another input source, press the EXT. DECODER button again so that "EXT. DECODER IN" goes off from the display, and then use the INPUT SELECTOR. 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
34
When you finish using this unit
Press the
STANDBY/ON
switch on the front panel or the
STANDBY
key on the remote controller to enter the standby
mode.
To select the source connected to this unit’s
EXTERNAL DECODER INPUT terminals as
the input source.
Press the
EXT. DECODER
button. “EXT. DECODER IN” will
appear on the display.
Note
The input source selected in this way has priority over any
other input source already selected.
To select another input source, press the
EXT. DECODER
button again so that “EXT. DECODER IN” goes off from the
display, and then use the
INPUT SELECTOR
.
Notes on input source selection
●
Note that selecting an input source means that the source
which is connected to the corresponding input terminals on
the rear panel is selected.
*
To select the source connected to the
VIDEO AUX
terminals on the front panel, select “
V-AUX
”.
●
The setting of the
EXT. DECODER
button cannot be
canceled by selecting another input source. To cancel it,
press the
EXT. DECODER
button again so that “EXT.
DECODER IN” goes off from the display.
●
If you select a video input source without canceling the
setting of the
EXT. DECODER
button, you will see the
picture of the video input source and hear the sound of the
source selected by the
EXT. DECODER
button.
●
If a different audio source is selected with the input selector
keys on the remote controller while enjoying a video source,
the sound from the newly selected audio source is heard,
but the picture from the video source can still be seen.
●
When you select an input source, the DSP program (or the
state of no DSP program is used) which was used when the
same input source was last selected will be automatically
recalled.
●
If a nonstandardized source is played back, or the unit
playing back a source is not operating correctly, “INPUT
DATA ERR” appears on the display.
Front panel
EXT. DECODER
STANDBY/ON
Front panel
Remote control
STANDBY
or
Remote control
EXT. DEC.
or
BASIC OPERATION