Yamaha DTX950K Assembly Manual

This manual describes the standard assembly of the DTX950K.

After assembling the parts and connecting the cords as shown below, the Drum Trigger Module is ready to be turned on.

•

To assemble the unit, make sure you have the following four pack-

ages: HXR4LD (Rack System), DTP900 (Pad Set), DTP902 (Pad

Set), DTX900 (Drum Trigger Module).

•

This manual covers how to attach the Pads and Drum Trigger Mod-

ule to the Rack System HXR4LD, for which assembly has already

been completed. Before performing the instructions described in

this manual, make sure to complete the Rack System HXR4LD by

following the corresponding Assembly Manual.

Before assembling the unit, lay a drum mat (sold separately) on the

floor. Alternately, to prevent damaging the floor, lay the cardboard of

the included packages, etc. on the floor before handling the Hi-Hat

Stand HS740A and Kick Pad KP125W.

Before using, please read this assembly manual, and use this product in a safe and proper manner.

*

Please keep this manual in a safe place for future reference.

*

Make sure to read the Assembly Manual of the Rack System and the Owner’s Manual of the Pad.

NOTICE

•

Make sure you hold onto the plug, not the cable, when connecting or disconnecting the cable. Also,

never place any heavy or sharp objects on the cable. Applying excessive force to the cable may

result in damage to the cable, such as the wires being severed, etc.

•

Do not step on or place heavy objects on the product. It may result in damage.

•

Do not use or keep the product in places with extremely high temperature (places in direct sunlight,

close to a heater, in a closed car, etc.) or high humidity (bathroom, outside on a rainy day, etc.).

Doing so may result in deformation, discoloration, damage or deterioration.

•

When cleaning the product, do not use benzine, thinner or alcohol as it may result in discoloration

or deformation. Please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If

the product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that

has been wrung out thoroughly to remove any remaining detergent. Also pay close attention so as

not to let the water and detergent come into contact with the cushions used in the product; doing so

may result in deterioration.

*

Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time without prior notice. Since specifica-

tions, equipment or options may not be the same in every locale, please check with your Yamaha dealer.

DTX950K

Assembly Manual

EN

Unit Standard Assembly

PCY155

(Cymbal Pad)

PCY135

(Cymbal Pad)

PCY135

(Cymbal Pad)

XP100T

(Tom Pad)

XP120T

(Tom Pad)

KP125W

(Kick Pad)

RHH135

(Real Hi-Hat Pad)

Drum Trigger

module DTX900

CH750

(Cymbal Holder)

CH755

(Cymbal Holder)

CH750

(Cymbal Holder)

SS662

(Snare Stand)

XP120SD

(Snare Pad)

HS740A

(Hi-Hat Stand)

HXR4LD

(Rack System)

IMPORTANT

NOTICE

PRECAUTIONS

If this symbol is ignored and the equipment is used improperly, fatal

injury to persons or serious damage could occur.

•

Do not let small children assemble or set up this product by themselves, or they may be injured.

Always assemble this product with adult supervision.

•

Be careful with the edges of the Cymbal Holders and the Tom Holders. The sharp holder ends

may result in injury.

•

Be careful with the edges of the spurs attached to the Kick Pad and foot pedal. The sharp ends

may result in injury.

•

If this product is used with a Rack System or Cymbal Stand, make sure all bolts are tightened

firmly. Also, when adjusting the height or angle, do not suddenly loosen the bolts. Loose bolts

may result in the rack overturning or parts dropping, causing injury.

•

Always set the product on a flat and solid surface. Placement on a sloping, unstable surface or on

steps may result in the product being unstable and subject to overturning.

•

When setting up the product, please pay close attention to the handling and setting of cables.

Carelessly placed cables may cause the user and others to trip and fall.

•

Do not alter the product. Doing so may result in injury or damage/deterioration to the product.

•

Do not sit or step on the rack. The rack may overturn or be damaged, resulting in injury.

WARNING

If this symbol is ignored and the equipment is used improperly,

there is a danger or injury to persons handling the equipment, and

material damage could occur.

•

Watch your fingers when adjusting clamps. They may become pinched, resulting in injury.

•

Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your

fingers.

•

Do not put your hands or feet under the foot pedal or foot switch. They may be pinched, resulting

in injury.

•

Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums

may drop, causing injury.

CAUTION

Assembling the Rack System

For details, refer to the Assembly Manual of the HXR4LD.

Checking the contents of each package

Mounting the Pads and the Drum Trigger Module on the Rack System

Mount the Pads and the Trigger Module on the Rack System. Then position the Kick Pad and the Hi-Hat.

1

2

Package 1 [DTP900]

❑

PCY135

(Cymbal Pad) (2)

❑

PCY155

(Cymbal Pad) (1)

❑

RHH135

(Real Hi-Hat Pad) (1)

❑

KP125W

(Kick Pad) (1)

❑

CH750

(Cymbal Holder) (2)

❑

SS662

(Snare Stand) (1)

❑

Stand base for the

RHH135 (1)

❑

Hi-Hat clutch for the

RHH135 (1)

❑

Cable band for the

RHH135 (1)

❑

Stoppers for the

PCY135/155 (3)

❑

Felts for the

PCY135/155 (3)

❑

2.5m stereo phone

cables (7)

❑

4m stereo phone

cables (4)

❑

Cable bands (10)

❑

2m spiral tube (1)

*

You can cut this tube to any desired length and

use it in order to take up any slack of the cables.

❑

Owner’s Manuals

(for each Pad)

• PCY65/65S/135/155

• KP125W

• RHH135

❑

Tuning key (1)

Package 3 [Drum Trigger Module DTX900]

❑

Drum Trigger Module

DTX900 (1)

❑

Module stand fastening

screws (4)

❑

Module Stand (1)

❑

AC Power

Adaptor (1)

❑

DTX900 Owner’s Manual (1)

❑

DTX900 Data List (1)

Package 2 [DTP902]

❑

XP100T (Tom Pad) (2)

❑

Clamp bolt (4)

❑

CH755

(Cymbal Holder) (1)

❑

HS740A

(Hi-Hat Stand) (1)

❑

XP120T (Tom Pad) (2)

❑

XP120SD (Snare Pad) (1)

❑

XP100T/100SD/120T/120SD

Owner’s Manual (1)

❑

Assembly Manual (this sheet, 1)

3

1.

Remove the cap of the rack by loosening the screw on

the top of the vertical support.

2.

Attach the Cymbal Holders (CH750 x 2 and CH755 x 1)

to the Rack System as shown below.

Attaching the Cymbal Holder

CH750

CH750

CH755

1.

Attach the clamp bolt then tighten it with five or

six turns on each of three Tom Pads.

2.

Attach four Tom Pads to the clamp rods on the

rack respectively. As shown below, attach the

Tom Pad to the rod part so that the rod part is to

be inserted to the hole of the Tom Pad, then

tighten the clamp bolt firmly.

3.

If you want to change the location (height and

angle) of the Tom Pad, use the clamp bolts A, B

and C. Loosen the one of the clamp bolts,

adjust the location of the Pad, then make sure

to tighten the clamp bolts again before adjust-

ing another clamp bolt.

Attaching the Tom Pad

XP100T

XP120T

Clamp bolt (to be

tightened as shown)

Tom pad (back side)

Clamp rod

Rod parts

Tom pad

Clamp bolt

To be

inserted

Clamp bolt B

Clamp bolt C

Clamp bolt A

Continued on the next page (on the back side)

U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation

©2009 Yamaha Corporation

WT58990

910PO***.*01A0

Printed in Japan

Yamaha DTX950K Assembly Manual

Yamaha DTX950K Manual

Yamaha DTX950K manual content summary: