Yamaha Dante-MY16-AUD Dante-MY16-AUD and R Series HA Remote Control Guide
Yamaha Dante-MY16-AUD Manual
 |
View all Yamaha Dante-MY16-AUD manuals
Add to My Manuals
Save this manual to your list of manuals |
Yamaha Dante-MY16-AUD manual content summary:
- Yamaha Dante-MY16-AUD | Dante-MY16-AUD and R Series HA Remote Control Guide - Page 1
Dante-MY16-AUD & R series HA Remote Control Guide 3rd Edition: August 2013 - Yamaha Dante-MY16-AUD | Dante-MY16-AUD and R Series HA Remote Control Guide - Page 2
Yamaha Commercial Audio Dante-MY16-AUD HA Remote Control Guide This guide describes the examples and setting procedures of a system where you remote-control the head amplifier (hereafter called the HA) of an I/O rack (Rio3224-D, Rio1608-D, Ri8-D, etc.) connected with the Dante audio network, via - Yamaha Dante-MY16-AUD | Dante-MY16-AUD and R Series HA Remote Control Guide - Page 3
Yamaha Commercial Audio System Examples Dante-MY16-AUD HA Remote Control Guide LS9 system example When inserting the Dante-MY16-AUD card into your LS9, you can remotecontrol the HA of an I/O rack on the Dante network from the LS9, with just a simple network connection. From the LS9, each Rio1608-D - Yamaha Dante-MY16-AUD | Dante-MY16-AUD and R Series HA Remote Control Guide - Page 4
Yamaha Commercial Audio Dante-MY16-AUD HA Remote Control Guide Multiple console system example You can also connect multiple consoles onto the Dante network to share an I/O rack. In this case, although an audio signal can be distributed to multiple consoles from the same I/O rack by patching with - Yamaha Dante-MY16-AUD | Dante-MY16-AUD and R Series HA Remote Control Guide - Page 5
Yamaha Commercial Audio Dante-MY16-AUD HA Remote Control Guide When the HA is controlled from the CL from one CL series console, you can also control the R series (in AD8HR mode) via a Dante-MY16-AUD inserted in slot 1. Examples of the system mixed with AD8HR The HA can be controlled even in the - Yamaha Dante-MY16-AUD | Dante-MY16-AUD and R Series HA Remote Control Guide - Page 6
Audio Equipment List Dante-MY16-AUD HA Remote Control Guide 1. Yamaha digital mixer (PM5D/PM5D-RH, M7CL-32/48, M7CL-48ES, LS9, DM2000, DM1000) or digital mixing engine (DME64N/24N) 2. Dante-MY16-AUD card (firmware v3.3.9 or later) 3. Dante-compatible Yamaha HA equipment (Rio3224-D, Rio1608 - Yamaha Dante-MY16-AUD | Dante-MY16-AUD and R Series HA Remote Control Guide - Page 7
Yamaha Commercial Audio Dante-MY16-AUD HA Remote Control Guide Connections for HA Control There are three types of the connections for HA remote control and bridge settings via the Dante-MY16-AUD card, as shown below. By default, no bridge is active (Mode 4); therefore, you need to set it with - Yamaha Dante-MY16-AUD | Dante-MY16-AUD and R Series HA Remote Control Guide - Page 8
Yamaha Commercial Audio Settings for R series Dante-MY16-AUD HA Remote Control Guide To remote-control the HA of the R series via the Dante-MY16-AUD card, you should set UNIT ID and the DIP switches at the front panel of the R series as follows, and then turn on the power. - Yamaha Dante-MY16-AUD | Dante-MY16-AUD and R Series HA Remote Control Guide - Page 9
Yamaha Commercial Audio Dante-MY16-AUD HA Remote Control Guide Setting examples of mixed models: UNIT ID settings System etc. The PM5D, the M7CL, the LS9-32, the LS9-16, the DM2000, and the DM1000 support eight, six, four, two, twelve, and four units, respectively. Patching of an audio signal is - Yamaha Dante-MY16-AUD | Dante-MY16-AUD and R Series HA Remote Control Guide - Page 10
Yamaha Commercial Audio Dante-MY16-AUD HA Remote Control Guide ・ If the R series in NATIVE mode and that in AD8HR mode coexist within one network, a duplicated UNIT ID between the different modes is acceptable (with the CL and R series firmware v1.5 or later). SECONDARY PORT Flip the DIP switch - Yamaha Dante-MY16-AUD | Dante-MY16-AUD and R Series HA Remote Control Guide - Page 11
Yamaha Commercial Audio Dante-MY16-AUD HA Remote Control Guide Settings by Dante Controller When you start Dante Controller, the Network View opens first, and all the Dante equipment on the network appear. This allows you to set the audio routing between Dante devices. Click a cell in the - Yamaha Dante-MY16-AUD | Dante-MY16-AUD and R Series HA Remote Control Guide - Page 12
Yamaha Commercial Audio Dante-MY16-AUD HA Remote Control Guide Settings for the Digital Mixer On the digital mixer, configure the same settings as those for remotecontrolling other external HA equipment. For details, please also refer to the Owner's Manual of the applicable digital mixer. WORD - Yamaha Dante-MY16-AUD | Dante-MY16-AUD and R Series HA Remote Control Guide - Page 13
Yamaha Commercial Audio Dante-MY16-AUD HA Remote Control Guide Using an External Word Clock Generator In the Word Clock menu of the mixer, select "Word Clock In" as the clock source. Open Dante Controller software and select the Clock Status tab. Set "Slave to External Clock" for just one of the - Yamaha Dante-MY16-AUD | Dante-MY16-AUD and R Series HA Remote Control Guide - Page 14
Yamaha Commercial Audio Dante-MY16-AUD HA Remote Control Guide Note: If the mixer cannot recognize HA equipment and the HA equipment does not appear on the screen of the mixer, please check the following. ・ Are the Dante-MY16-AUD firmware and Dante Controller updated to a version that supports the
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
 |
 |
Dante-MY16-AUD & R series
HA Remote Control Guide
3rd Edition: August 2013