Yamaha EMX5000-20 Owner's Manual - Page 14

Master control TR IN PFL pre-fader listen switch, AUX 1 fader, MONO OUT fader - 20

Get Yamaha EMX5000-20 PDF manuals and user guides View all Yamaha EMX5000-20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

12 Front and rear panel G PFL (pre-fader listen) switch When this switch is turned on, the signal at the point before the ST control knob F is sent to the PHONES jack (input/output panel D). Note: The ST control setting does not affect the level of the signal sent to the PFL/AFL buses (pre-fader send). s Master control section In this section, you can adjust the final level of the outputs. L H I J K H AUX 1 fader The AUX 1 fader adjusts the final level of the signal sent from the AUX 1 bus to the AUX SEND 1 jack (input/output panel 8). If the Power amp select switch Y is set to AUX 1-MONO, using this fader enables you to adjust the level of the signal sent from the SPEAKERS A 1/2 jacks to the speakers. I AUX 2 fader The AUX 2 fader adjusts the final level of the signal output from the AUX 2 bus to the AUX SEND 2 jack (input/output panel 8). If the Power amp select switch Y is set to AUX 1AUX 2, using this fader enables you to adjust the level of the signal sent from the SPEAKERS B 1/2 jacks to the speakers. J MONO OUT fader The MONO OUT fader adjusts the final level of the monaural signal output from the STEREO bus to the MONO OUT jack (input/output panel C). If the Power amp select switch Y is set to AUX 1MONO, this fader also adjusts the level of the signal sent from the SPEAKERS B 1/2 jacks to the speakers. If the Power amp select switch Y is set to MONO BRIDGE, this fader adjusts the level of the signal sent from the SPEAKERS A 1 jacks to the speaker. K ST OUT fader The ST OUT fader adjusts the final level of the signal sent from the STEREO bus to the ST OUT jacks (input/output panel 0). If the Power amp select switch Y is set to ST L-R, this fader also adjusts the level of the signal sent to the SPEAKERS jacks (rear panel 3). Note: The setting of this fader does not affect the signal output from the STEREO bus to the ST SUB OUT jacks. L AFL (after fader listen) switch When this switch is on, the output signal that passes through the corresponding fader is sent to the PHONES jack (input/output panel D). Use these switches when you wish to monitor a particular output signal through the headphones. s 2TR IN section In this section, you can adjust the input level of a cassette deck or a CD player that is connected to the 2TR IN jacks (input/output panel 5). M N M ST (stereo) control This knob adjusts the level of the signal sent from the 2TR IN jacks to the STEREO bus. N PFL (pre-fader listen) switch When this switch is on, the signal input from the 2TR IN jacks is routed at the point before the ST control M to the PHONES jack (input/output panel D). EMX5000-20/EMX5000-12-Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
12
Front and rear panel
EMX5000-20/EMX5000-12—Owner’s Manual
G
PFL (pre-fader listen) switch
When this switch is turned on, the signal at the
point before the ST control knob
F
is sent to the
PHONES jack (input/output panel
D
).
■
Master control section
In this section, you can adjust the final level of
the outputs.
H
AUX 1 fader
The AUX 1 fader adjusts the final level of the sig-
nal sent from the AUX 1 bus to the AUX SEND 1
jack (input/output panel
8
). If the Power amp
select switch
Y
is set to AUX 1-MONO, using
this fader enables you to adjust the level of the
signal sent from the SPEAKERS A 1/2 jacks to the
speakers.
I
AUX 2 fader
The AUX 2 fader adjusts the final level of the sig-
nal output from the AUX 2 bus to the AUX
SEND 2 jack (input/output panel
8
). If the
Power amp select switch
Y
is set to AUX 1-
AUX 2, using this fader enables you to adjust the
level of the signal sent from the SPEAKERS B 1/2
jacks to the speakers.
J
MONO OUT fader
The MONO OUT fader adjusts the final level of
the monaural signal output from the STEREO
bus to the MONO OUT jack (input/output panel
C
).
If the Power amp select switch
Y
is set to AUX 1-
MONO, this fader also adjusts the level of the sig-
nal sent from the SPEAKERS B 1/2 jacks to the
speakers.
If the Power amp select switch
Y
is set to MONO
BRIDGE, this fader adjusts the level of the signal
sent from the SPEAKERS A 1 jacks to the speaker.
K
ST OUT fader
The ST OUT fader adjusts the final level of the
signal sent from the STEREO bus to the ST OUT
jacks (input/output panel
0
). If the Power amp
select switch
Y
is set to ST L-R, this fader also
adjusts the level of the signal sent to the SPEAK-
ERS jacks (rear panel
3
).
L
AFL (after fader listen) switch
When this switch is on, the output signal that
passes through the corresponding fader is sent to
the PHONES jack (input/output panel
D
). Use
these switches when you wish to monitor a par-
ticular output signal through the headphones.
■
2TR IN section
In this section, you can adjust the input level of a
cassette deck or a CD player that is connected to
the 2TR IN jacks (input/output panel
5
).
M
ST (stereo) control
This knob adjusts the level of the signal sent from
the 2TR IN jacks to the STEREO bus.
N
PFL (pre-fader listen) switch
When this switch is on, the signal input from the
2TR IN jacks is routed at the point before the ST
control
M
to the PHONES jack (input/output
panel
D
).
Note:
The ST control setting does not affect
the level of the signal sent to the PFL/AFL buses
(pre-fader send).
H
I
J
K
L
Note:
The setting of this fader does not affect
the signal output from the STEREO bus to the
ST SUB OUT jacks.
N
M