Yamaha EMX5000-20 Owner's Manual - Page 22

Bridge connection, Caution, When using a bridge connection, Two-channel connection

Get Yamaha EMX5000-20 PDF manuals and user guides View all Yamaha EMX5000-20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

20 Installation/Connections • Two channel parallel connections If you connect two speakers in parallel to the SPEAKERS A and SPEAKERS B jacks, use speakers with an impedance in the range of 8-16 ohms. A maximum output of 500W + 500W will be obtained when 8-ohm speakers are used. Two-channel connection Two-channel parallel connection or 4Ω-8Ω 4Ω-8Ω 8Ω-16Ω 8Ω-16Ω 8Ω-16Ω 8Ω-16Ω Main Main/Monitor Main Main/Monitor Speaker Speaker Speaker Speaker or * Use either the 1 (Speakon) jacks or 2 (phone) jacks of and . * Use either the 1 (Speakon) jacks or 2 (phone) jacks of and . s When the power amp select switch is set to MONO BRIDGE: • Bridge connection Connect only one 8-16 ohm speaker to the A1 jack. The speaker will output the combined monaural signal of the STEREO bus. A maximum output of 1000 W will be obtained when an 8-ohm speaker is used. If you are inputting a signal from the P.AMP IN jack, input it to P.AMP IN jack A. Caution: When using a bridge connection, do not connect a speaker to the B or A 2 jack. Bridge connection No connection No connection * Use the 1+(+) and 2+(-) pins of the 1 jack. 8Ω-16Ω Main Speaker EMX5000-20/EMX5000-12-Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
20
Installation/Connections
EMX5000-20/EMX5000-12—Owner’s Manual
• Two channel parallel connections
If you connect two speakers in parallel to the SPEAKERS A and SPEAKERS B jacks, use speakers with an
impedance in the range of 8–16 ohms. A maximum output of 500W + 500W will be obtained when 8-ohm
speakers are used.
■
When the power amp select switch is set to MONO BRIDGE:
•
Bridge connection
Connect only one 8–16 ohm speaker to the A1 jack. The speaker will output the combined monaural signal of
the STEREO bus. A maximum output of 1000 W will be obtained when an 8-ohm speaker is used.
If you are inputting a signal from the P.AMP IN jack, input it to P.AMP IN jack A.
Caution:
When using a bridge connection,
do not connect a speaker to the B or A 2 jack.
Two-channel connection
Two-channel parallel connection
Main
Speaker
Main/Monitor
Speaker
Main
Speaker
Main/Monitor
Speaker
or
or
* Use either the 1 (Speakon) jacks
or 2 (phone) jacks of
and
.
* Use either the 1 (Speakon) jacks
or 2 (phone) jacks of
and
.
4
Ω
–8
Ω
4
Ω
–8
Ω
8
Ω
–16
Ω
8
Ω
–16
Ω
8
Ω
–16
Ω
8
Ω
–16
Ω
Main Speaker
Bridge connection
No
connection
* Use the 1+(+) and 2+(–) pins of the
1
jack.
8
Ω
–16
Ω
No
connection