Yamaha EMX62M Owner's Manual
Yamaha EMX62M Manual
View all Yamaha EMX62M manuals
Add to My Manuals
Save this manual to your list of manuals |
Yamaha EMX62M manual content summary:
- Yamaha EMX62M | Owner's Manual - Page 1
Owner's Manual Keep This Manual For Future Reference. E - Yamaha EMX62M | Owner's Manual - Page 2
E Revisions Thank you for purchasing the Yamaha EMX62M Powered Mixer. Parts of the EMX62M owner's manual have been revised. Please refer to the following revisions rather than the corresponding sections of the original owner's manual. P.11 ■ MAIN section D C C Level Meter This LED display - Yamaha EMX62M | Owner's Manual - Page 3
Digital Musical Instrument Division, Yamaha Corporation © 2002 Yamaha Corporation CH IN 1-4 Low PA LIMIT SUM [0dB] SUM [0dB] MASTER BA [-6dB] BA MONITOR OUT [+4dB] EFFECT OUT [+4dB] 2 1 1 SPEAKERS OUT, EFFECT OUT [+4dB] SPEAKERS OUT MAXIMUM OUTPUT POWER [200W/4Ω] NOMINAL OUTPUT [40W/4Ω] - Yamaha EMX62M | Owner's Manual - Page 4
will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with - Yamaha EMX62M | Owner's Manual - Page 5
may induce noise. If noise occurs, use the telephone away from the unit. Volume level setting • Do not set all equalizer controls and faders to maximum. Doing so may cause oscillation depending on the condition of the connected unit and speakers, and may damage the speakers. EMX62M-Owner's Manual - Yamaha EMX62M | Owner's Manual - Page 6
4 Precautions EMX62M-Owner's Manual - Yamaha EMX62M | Owner's Manual - Page 7
you for purchasing the Yamaha EMX62M Powered Mixer. In order to take full advantage of the EMX62M and enjoy long and trouble-free operation, read this owner's manual carefully, and keep it in a safe place for future reference. Features • The EMX62M's six input channels support a wide range of audio - Yamaha EMX62M | Owner's Manual - Page 8
Connecting speakers Using speaker cables, connect each speaker to the SPEAKERS 1 and 2 jack on the rear panel of the EMX62M. Connecting a microphone Make sure that the power is turned off to the EMX62M. Connect a microphone to the Low-Z jack of channel 1-4. EMX62M Microphone Using a condenser - Yamaha EMX62M | Owner's Manual - Page 9
Super Hi-Z jacks to connect multiple instruments. You cannot use the Hi-Z jack and the Low-Z jack for the same channel at the same time. If a microphone has already been connected to the Low-Z jack of a channel, you cannot connect an instrument to the Hi-Z jack of the channel. EMX62M-Owner's Manual - Yamaha EMX62M | Owner's Manual - Page 10
effect applied by using the EFFECT control of the target channel and the EFFECT RTN control in the MAIN section. EMX62M • Be sure to follow the power up sequence specified above to prevent the speakers from being damaged. • The speakers do not have a power switch. STEP 3 Sound output Set the MASTER - Yamaha EMX62M | Owner's Manual - Page 11
that is fed to the MAIN bus and internal power amplifier. The MAIN bus signal is routed to the MAIN OUTPUT jack (input/output panel 9), SPEAKERS 1 and 2 jacks (rear panel 1), and through 4, or if a microphone signal is distorted, use the PAD switch to attenuate the input signal. EMX62M-Owner's Manual - Yamaha EMX62M | Owner's Manual - Page 12
effects processor on and off and select effects programs. 6 s MAIN Section The MAIN section is used to set the MAIN MASTER level, 7-band graphic equalizer, AUX IN and 2TR IN levels, and MAIN control determines the output level of the MAIN OUT, speaker outputs, and PHONES. EMX62M-Owner's Manual - Yamaha EMX62M | Owner's Manual - Page 13
G Q PHANTOM switch and indicator This switch turns the phantom power supply on/ off for the Low-Z input jacks of channels 1-4. When the switch is turned on, the indicator lights up. Turn this switch off if you do not use it. s YAMAHA SPEAKER PROCESSING R ON/OFF switch This switch enables you to - Yamaha EMX62M | Owner's Manual - Page 14
of each channel cannot be used simultaneously. Use the input appropriate for the source. Since phantom power is turned on and off for inputs channels 1 through The FOOT SW jack is used to connect an optional footswitch, such as the Yamaha FC5, which can be used to turn the built- EMX62M-Owner's Manual - Yamaha EMX62M | Owner's Manual - Page 15
input of a powered monitor speaker. K PHONES-OUTPUT jack The PHONES-OUTPUT phone jack outputs the MAIN bus signal after the 7-band graphic equalizer and MASTER level control, and can be connected to a pair of stereo headphones for personal monitoring. Front & Rear Panels 13 EMX62M-Owner's Manual - Yamaha EMX62M | Owner's Manual - Page 16
output the main signal from the internal power amplifier and are used to connect speakers. They are internally connected in parallel and output the same signal. Connecting one speaker Connecting two speakers 1 Installation The EMX62M uses a forced cooling system with intake on the bottom of the - Yamaha EMX62M | Owner's Manual - Page 17
Panels 15 Recorder (Cassette, DAT, MD) Headphones *2 Powered monitor Microphone *1 Footswitch (YAMAHA FC5) VOL Larger mixer or Amplifier Electric-acoustic guitar Electric bass * The Low-Z and Hi-Z input of each channel cannot be used simultaneously. *1. Although this example shows an external - Yamaha EMX62M | Owner's Manual - Page 18
the main output. G Use the MAIN MASTER control to set the overall volume level of the main mix. Monitoring By connecting a powered monitor speaker to the MONITOR OUTPUT, you can create a monitor mix independent of the MAIN mix, since the EMX62M-Owner's Manual input channel MONITOR controls are not - Yamaha EMX62M | Owner's Manual - Page 19
a 7U space to install the rack mount. After installation, the unit will project 62 mm from the front surface of the rack. 62 2 Attach one of the rack mount brackets to the side of the EMX62M using three included screws. 3 Attach the other rack mount bracket in the same way. EMX62M-Owner's Manual - Yamaha EMX62M | Owner's Manual - Page 20
AUX IN control in the MAIN section may not be rotated to right. A: The MONITOR controls for input channels may not have been adjusted. A: You cannot use the Low-Z jack and the Hi-Z jack for the same channel at the same time. A: Yes. Use a speaker with an impedance of 4-8 ohms. EMX62M-Owner's Manual - Yamaha EMX62M | Owner's Manual - Page 21
channel equalization Meters Graphic equalizer Internal digital effect Phantom power Limiter LIMIT indicator Protection circuit (Power amp) Foot switch (FC5) Optional accessories Power requirement Power consumption Dimensions (WxHxD) Weight Supplied accessories 135 W/8Ω @0.5% THD at 1 kHz (SPEAKERS - Yamaha EMX62M | Owner's Manual - Page 22
Specifications nominal output level when the unit is set at maximum gain. (All level controls Vrms. ■ Output Specifications Output connectors SPEAKERS OUT (1, 2) MAIN OUT MONITOR OUT Dimensions 328 482 305 Specifications are subject to change without prior notice. EMX62M-Owner's Manual Unit: mm - Yamaha EMX62M | Owner's Manual - Page 23
PA LIMIT SUM [0dB] SUM [0dB] MASTER BA [-6dB] BA MONITOR OUT [+4dB] EFFECT OUT [+4dB] 2 1 1 SPEAKERS OUT 2 [200W/4Ω] 1 2 PHONES OUT Block & Level Diagrams 21 EMX62M-Owner's Manual , MONITOR OUT, EFFECT OUT [+4dB] SPEAKERS OUT MAXIMUM OUTPUT POWER [200W/4Ω] [+24dB] PHONES max (175mW - Yamaha EMX62M | Owner's Manual - Page 24
- Yamaha EMX62M | Owner's Manual - Page 25
- Yamaha EMX62M | Owner's Manual - Page 26
V833080 R1 1 AP 24 NP Printed in Taiwan YAMAHA CORPORATION Pro Audio & Digital Musical Instrument Division P.O. Box 3, Hamamatsu, 430-8651, Japan
E
Owner’s Manual
Keep This Manual For Future Reference.