Yamaha EMX68S Owner's Manual

Yamaha EMX68S Manual

Get Yamaha EMX68S PDF manuals and user guides View all Yamaha EMX68S manuals
Add to My Manuals
Save this manual to your list of manuals

Yamaha EMX68S manual content summary:

  • Yamaha EMX68S | Owner's Manual - Page 1
    Owner's Manual Keep This Manual For Future Reference. E
  • Yamaha EMX68S | Owner's Manual - Page 2
    Revisions E Thank you for purchasing the Yamaha EMX88S/EMX68S Powered Mixer. Parts of the EMX88S, EMX68S owner's manual have been revised. Please refer to the following revisions rather than the corresponding sections of the original owner's manual. P.12 ■ MAIN section F F Level Meter This LED
  • Yamaha EMX68S | Owner's Manual - Page 3
    ■ Block and Level diagram 6 EMX88S/EMX68S CH INPUT (CH1-2) (CH1-4) Low-Z [-50/-20dB] Hi-Z [-40/-10dB 1 2 YSP ON/OFF LIMITER 1 MONITOR [+4dB] 125Hz 250Hz 500Hz 1kHz 2kHz 4kHz 8kHz LED METER (5 point) SPEAKERS OUT 1 A [400W/4Ω] 2 BRIDGE [800W/8Ω] 1 B [400W/4Ω] 2 SUM INV SUM [-6dB] [+4dB] BA
  • Yamaha EMX68S | Owner's Manual - Page 4
    generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA 90620 The above statements apply ONLY to those products distributed by Yamaha
  • Yamaha EMX68S | Owner's Manual - Page 5
    noise. If noise occurs, use the telephone away from the unit. Volume level setting • Do not set all equalizer controls and faders to maximum. Doing so may cause oscillation depending on the condition of the connected unit and speakers, and may damage the speakers. EMX88S/EMX68S-Owner's Manual
  • Yamaha EMX68S | Owner's Manual - Page 6
    4 Precautions EMX88S/EMX68S-Owner's Manual
  • Yamaha EMX68S | Owner's Manual - Page 7
    As a conference PA system/installed sound system 22 As a band PA 23 Installing an optional rack mount kit 25 Troubleshooting 26 Specifications 27 General specifications 27 Input specifications 28 Output specifications 28 Dimensions 29 Block and Level diagram 30 EMX88S/EMX68S-Owner's Manual
  • Yamaha EMX68S | Owner's Manual - Page 8
    Be sure to use a cable designed for speaker connection. EMX88S (EMX68S) Setting the power amplifier mode Set the power amp select switch (located on the right corner on the panel) to MAIN L-R. EMX88S (EMX68S) EMX88S/EMX68S-Owner's Manual Power amp select switch • This Quick Guide assumes that two
  • Yamaha EMX68S | Owner's Manual - Page 9
    . • You cannot use the Hi-Z jack and the Low-Z jack for the same channel at the same time. If a microphone has already been connected to the Low-Z jack of a channel, you cannot connect a player to the Hi-Z jack of the channel. • Connect a recorder to the REC OUT jacks. EMX88S/EMX68S-Owner's Manual
  • Yamaha EMX68S | Owner's Manual - Page 10
    on the EMX88S/EMX68S to turn on the power. EMX88S (EMX68S) Synthesizer, Drum machine, Guitar processor EMX88S/EMX68S-Owner's Manual • Be sure to follow the power up sequence specified above to prevent the speakers from being damaged. • To correct the low range, turn on the YAMAHA SPEAKER PROCESSING
  • Yamaha EMX68S | Owner's Manual - Page 11
    follow the power off sequence specified above to prevent the speakers from being damaged. • Set the MASTER controls in the MAIN section and the MONITOR section to "0" for use next time (so that a loud noise will not sound the next time you turn on the power to the unit). EMX88S/EMX68S-Owner's Manual
  • Yamaha EMX68S | Owner's Manual - Page 12
    channel. 6 PAD switch (1-6 (EMX88S) only, 1-4 (EMX68S) only) This switch attenuates the input signal by 30 dB. When connecting a line level device to channels 1-6 (EMX88S), 1-4 (EMX68S), or if the mic input is distorted, turn this switch on (the pressed-in position). EMX88S/EMX68S-Owner's Manual
  • Yamaha EMX68S | Owner's Manual - Page 13
    even if the power is turned off. Use this control to adjust the effect signal sent to the stereo (MAIN L, R) bus from the built-in digital effect. C AUX IN control This control adjusts the amount of signal that is sent from the AUX IN jack to the stereo (MAIN L, R) bus. EMX88S/EMX68S-Owner's Manual
  • Yamaha EMX68S | Owner's Manual - Page 14
    L, R) bus signal output level. This setting is output to the SPEAKERS A, B, BRIDGE jacks and the MAIN (STEREO) jack (input/output power supply on/ off for the Low-Z XLR type input jacks of channels 1-6 (EMX88S), 1-4 (EMX68S). Turn this switch off if you do not use it. EMX88S/EMX68S-Owner's Manual
  • Yamaha EMX68S | Owner's Manual - Page 15
    indicator Q Q Power ON/OFF switch and indicator This switch turns the power of the EMX88S/ EMX68S on/off. When the switch is turned on, the indicator lights up. Note: Before turning the EMX88S/EMX68S on/ off, turn down the MASTER controls of the MONITOR and MAIN section. EMX88S/EMX68S-Owner's Manual
  • Yamaha EMX68S | Owner's Manual - Page 16
    . Nominal input level is -50 dB for the MIC jacks and -10 dB for the LINE jacks. Note: The MIC and LINE inputs for channel 7 (EMX88S), 5 (EMX68S) can be used simultaneously but their levels cannot be adjusted separately (Same for channel 8 (EMX88S), 6 (EMX68S).) EMX88S/EMX68S-Owner's Manual
  • Yamaha EMX68S | Owner's Manual - Page 17
    control of each channel will be sent Yamaha FC5 foot switch (sold separately) to this jack and use EMX68S to external devices. A stereo recording device such as a cassette recorder or MD recorder can be connected to the REC OUT jacks, and a playback device such a power EMX88S/EMX68S-Owner's Manual
  • Yamaha EMX68S | Owner's Manual - Page 18
    output jacks (SPEAKERS) Connect speakers here. The EMX88S/EMX68S has two internal power amps. There are three ways in which speakers can be connected to the EMX88S/EMX68S. • Two-channel connection • Two-channel parallel connection • Bridge connection At this time, use the power amp select switch
  • Yamaha EMX68S | Owner's Manual - Page 19
    connections If you connect two speakers to each set of outputs, use speakers with an impedance in the range of 8-16 ohms. A maximum output of 400W + 400W will be obtained when 8-ohm speakers are used. Power amp select switch or Not used 8Ω-16Ω 8Ω-16Ω 8Ω-16Ω 8Ω-16Ω EMX88S/EMX68S-Owner's Manual
  • Yamaha EMX68S | Owner's Manual - Page 20
    accidentally connected to it when you are using two-channel or two-channel parallel connections. Remove this protective cap only when making a bridge connection. s Connecting a monitor speaker You can connect a powered speaker to the MONITOR jack. VOL Powered monitor EMX88S/EMX68S-Owner's Manual
  • Yamaha EMX68S | Owner's Manual - Page 21
    Electric bass Electric-acoustic guitar * Speakers normally connect to the jacks on the rear panel. When more speaker outputs are needed, use the MAIN (STEREO) jacks are for stereo output and the MONITOR jack is for monaural output. Power amp Monitor Speakers EMX88S/EMX68S-Owner's Manual
  • Yamaha EMX68S | Owner's Manual - Page 22
    to apply the digital effect. 5 Use the MAIN/MONITOR section EFFECT RTN control to adjust the level of the sound processed by the effect. Note: If the effect sound is distorted even if the EFFECT RTN is turned all the way down, lower the EFFECT controls of each channel. EMX88S/EMX68S-Owner's Manual
  • Yamaha EMX68S | Owner's Manual - Page 23
    sense of pitch to the tone. Effective on sounds that contain numerous overtones. The well-known effect used to distort the sound. This effect sets the delay time to the interval at which you actually press can not blink any faster than an interval of 256 ms (234.3 bpm). EMX88S/EMX68S-Owner's Manual
  • Yamaha EMX68S | Owner's Manual - Page 24
    EMX88S/EMX68S can be used, and explains connections and operation. As a conference PA system/installed sound system This example shows the EMX88S/EMX68S used as a conference PA system or sound system. A sound mix different from that of the main speakers can be sent to the powered monitor speakers
  • Yamaha EMX68S | Owner's Manual - Page 25
    a band PA 23 As a band PA Here is an example of using the EMX88S/EMX68S as a small PA for a band. In this example, an external effect such as delay or reverb is also being used. Connections Main Speakers SPEAKERS A 1 Set to MAIN (L+R) - MON 2 SPEAKERS B 1 2 Monitor Speakers Microphone Electric
  • Yamaha EMX68S | Owner's Manual - Page 26
    • Connect mics or instruments, such as keyboards, to the channel input jacks. • Connect the main speakers to the SPEAKERS A, B 1/2 jacks and the monitor speakers. • If you will be using an external effect such as delay or reverb, connect the EMX88S/EMX68S's EFFECT OUT jack to the input jack of the
  • Yamaha EMX68S | Owner's Manual - Page 27
    install the rack mount. After installation, the unit will project 62 mm from the front surface of the rack. 62 2 Attach one of the rack mount brackets to the side of the EMX88S/EMX68S using three included screws. 3 Attach the other rack mount bracket in the same way. EMX88S/EMX68S-Owner's Manual
  • Yamaha EMX68S | Owner's Manual - Page 28
    control in the MAIN section may not be rotated to right. A: The MONITOR controls for input channels may not have been adjusted. A: You cannot use the Low-Z jack and the Hi-Z jack for the same channel at the same time. A: Yes. Use a speaker with an impedance of 4-8 ohms. EMX88S/EMX68S-Owner's Manual
  • Yamaha EMX68S | Owner's Manual - Page 29
    delay Optional accessories Power requirement/ Power consumption Dimensions (WxHxD) RK-88, FC5 USA and Canada Europe Other 482×305×328 mm 120 V AC 60 Hz/300W 230 V AC 50 Hz/350W 240 V AC 50 Hz/350W Weight 15.5 kg Supplied accessories AC power cord, Owner's Manual EMX88S/EMX68S-Owner's Manual
  • Yamaha EMX68S | Owner's Manual - Page 30
    Specifications . • 0 dB=0.775 Vrms, 0 dBV=1 Vrms. Nominal impedance 4/8Ω Speaker 8Ω Speaker 10 kΩ Lines 10 kΩ Lines 10 kΩ Lines 10 kΩ Lines Output level User Information specified in EN55103-1 and EN55103-2. Inrush Current: 75A Conformed Environment: E1, E2, E3 and E4 EMX88S/EMX68S-Owner's Manual
  • Yamaha EMX68S | Owner's Manual - Page 31
    s Dimensions 328 305 Dimensions 29 482 Unit: mm EMX88S/EMX68S-Owner's Manual
  • Yamaha EMX68S | Owner's Manual - Page 32
    30 Specifications s Block and Level diagram EMX88S/EMX68S-Owner's Manual CH INPUT (CH1-2) (CH1-4) Low-Z [-50/-20dB] Hi-Z [-40/-10dB] CH ] MAIN OUT [+4dB] MONITOR OUT [+4dB] EFFECT OUT [+4dB] MAXIMUM OUTPUT POWER [400W/4Ω] SPEAKERS OUT (80W/4Ω) +40dB +30dB +20dB +10dB 0dB -10dB -20dB
  • Yamaha EMX68S | Owner's Manual - Page 33
  • Yamaha EMX68S | Owner's Manual - Page 34
    V832100 R0 1 AP 32 NP Printed in Taiwan YAMAHA CORPORATION Pro Audio & Digital Musical Instrument Division P.O. Box 3, Hamamatsu, 430-8651, Japan
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
Owner’s Manual
E
Keep This Manual For Future Reference.