Yamaha HTR-4065 Owners Manual - Page 92

Error indications on the front display, APPENDIX

Get Yamaha HTR-4065 PDF manuals and user guides View all Yamaha HTR-4065 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

Error indications on the front display Message Access denied Access error Check SP Wires Connect error Internal Error No content No device Please wait RemID Mismatch Unable to play Unknown iPod USB Overloaded Cause Remedy Access to the PC is denied. Configure the sharing settings and select the unit as a device to which music contents are shared (p.53). The unit cannot access the USB device. Turn off the unit and reconnect your USB device. If the problem persists, try another USB device. The unit cannot access the iPod. Turn off the iPod and turn it on again. Make sure your router and modem are turned on. There is a problem with the signal path from the network to the unit. Check the connection between the unit and your router (or hub) (p.27). The speaker cables short circuit. Twist the bare wires of the cables firmly and connect to the unit and speakers properly. The unit has detected the iPod, but cannot access it. Turn off the iPod and then turn it on again. An internal error has occurred. Contact the nearest authorized Yamaha dealer or service center. There are no playable files in the selected folder. Select a folder that contains files supported by the unit. The unit cannot detect the USB device. Turn off the unit and reconnect your USB device. If the problem persists, try another USB device. The unit cannot detect the iPod. Turn off the iPod and then turn it on again. The unit is preparing for connecting to the network. Wait until the message disappears. If the message stays more than 3 minutes, turn off the unit and turn it on again. The remote control IDs of the unit and the remote control are not identical. Change the remote control ID of the unit or the remote control (p.80). The unit cannot play back the songs stored on the iPod for some Check the song data. If it cannot be played on the iPod itself, the song data or storage area may be reason. defective. The unit cannot play back the songs stored on the PC for some reason. Check if the format of files you are trying to play is supported by the unit. For information about the formats supported by the unit, see "Playing back music stored on media servers (PCs/NAS)" (p.53). If the unit supports the file format, but still cannot play back any files, the network may be overloaded with heavy traffic. The connected iPod is not supported by the unit. Use an iPod supported by the unit (p.46). An overcurrent is flowing through the USB device. Turn off the unit and reconnect your USB device. If the problem persists, try another USB device. APPENDIX ➤ Error indications on the front display En 92

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
APPENDIX
➤
Error indications on the front display
En
92
Error indications on the front display
Message
Cause
Remedy
Access denied
Access to the PC is denied.
Configure the sharing settings and select the unit as a device to which music contents are shared
(p.53).
Access error
The unit cannot access the USB device.
Turn off the unit and reconnect your USB device. If the problem persists, try another USB device.
The unit cannot access the iPod.
Turn off the iPod and turn it on again.
There is a problem with the signal path from the network to the unit.
Make sure your router and modem are turned on.
Check the connection between the unit and your router (or hub) (p.27).
Check SP Wires
The speaker cables short circuit.
Twist the bare wires of the cables firmly and connect to the unit and speakers properly.
Connect error
The unit has detected the iPod, but cannot access it.
Turn off the iPod and then turn it on again.
Internal Error
An internal error has occurred.
Contact the nearest authorized Yamaha dealer or service center.
No content
There are no playable files in the selected folder.
Select a folder that contains files supported by the unit.
No device
The unit cannot detect the USB device.
Turn off the unit and reconnect your USB device. If the problem persists, try another USB device.
The unit cannot detect the iPod.
Turn off the iPod and then turn it on again.
Please wait
The unit is preparing for connecting to the network.
Wait until the message disappears. If the message stays more than 3 minutes, turn off the unit and turn
it on again.
RemID Mismatch
The remote control IDs of the unit and the remote control are not
identical.
Change the remote control ID of the unit or the remote control (p.80).
Unable to play
The unit cannot play back the songs stored on the iPod for some
reason.
Check the song data. If it cannot be played on the iPod itself, the song data or storage area may be
defective.
The unit cannot play back the songs stored on the PC for some
reason.
Check if the format of files you are trying to play is supported by the unit. For information about the
formats supported by the unit, see “Playing back music stored on media servers (PCs/NAS)” (p.53). If
the unit supports the file format, but still cannot play back any files, the network may be overloaded with
heavy traffic.
Unknown iPod
The connected iPod is not supported by the unit.
Use an iPod supported by the unit (p.46).
USB Overloaded
An overcurrent is flowing through the USB device.
Turn off the unit and reconnect your USB device. If the problem persists, try another USB device.