Yamaha HTR 6230 Owner's Manual - Page 12

PREPARATION, Preparation of remote control

Get Yamaha HTR 6230 - AV Receiver PDF manuals and user guides
UPC - 027108933054
View all Yamaha HTR 6230 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

PREPARATION Preparation of remote control Installing batteries in the remote control 13 Using the remote control The remote control transmits a directional infrared ray. Be sure to aim the remote control directly at the remote control sensor on this unit during operation. 2 30º 30º Approximately 6 m (20 ft) 1 Take off the battery compartment cover. 2 Insert the four supplied batteries (AAA, R03, UM-4) according to the polarity markings (+ and -) on the inside of the battery compartment. 3 Snap the battery compartment cover back into place. Notes • Change all of the batteries if you notice the following conditions: - the operation range of the remote control decreases. • Do not use old batteries together with new ones. • Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these different types of batteries may have the same shape and color. • If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries. • Do not throw away batteries with general house waste; dispose of them correctly in accordance with your local regulations. • If the remote control is without batteries for more than 2 minutes, or if exhausted batteries remain in the remote control, the contents of the memory may be cleared. When the memory is cleared, insert new batteries and set up the remote control code. a Infrared window Outputs infrared control signals. Aim this window at the component you want to operate. y • To set the remote control codes for other components, see page 39. Notes • Do not spill water or other liquids on the remote control. • Do not drop the remote control. • Do not leave or store the remote control in the following types of conditions: - places of high humidity, such as near a bath - places of high temperature, such as near a heater or stove - places of extremely low temperatures - dusty places • To set the remote control codes for other components, see page 39. 8 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
8
En
PREPARATION
1
Take off the battery compartment cover.
2
Insert the four supplied batteries (AAA, R03,
UM-4) according to the polarity markings (+
and –) on the inside of the battery
compartment.
3
Snap the battery compartment cover back
into place.
Notes
•
Change all of the batteries if you notice the following conditions:
–
the operation range of the remote control decreases.
•
Do not use old batteries together with new ones.
•
Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as
these different types of batteries may have the same shape and
color.
•
If the batteries have leaked, dispose of them immediately. Avoid
touching the leaked material or letting it come into contact with
clothing, etc. Clean the battery compartment thoroughly before
installing new batteries.
•
Do not throw away batteries with general house waste; dispose of
them correctly in accordance with your local regulations.
•
If the remote control is without batteries for more than 2 minutes,
or if exhausted batteries remain in the remote control, the contents
of the memory may be cleared. When the memory is cleared, insert
new batteries and set up the remote control code.
The remote control transmits a directional infrared ray.
Be sure to aim the remote control directly at the remote
control sensor on this unit during operation.
a
Infrared window
Outputs infrared control signals. Aim this window at the
component you want to operate.
y
•
To set the remote control codes for other components, see page 39.
Notes
•
Do not spill water or other liquids on the remote control.
•
Do not drop the remote control.
•
Do not leave or store the remote control in the following types of
conditions:
–
places of high humidity, such as near a bath
–
places of high temperature, such as near a heater or stove
–
places of extremely low temperatures
–
dusty places
•
To set the remote control codes for other components, see page 39.
Preparation of remote control
Installing batteries in the remote control
1
3
2
Using the remote control
30º
30º
Approximately 6 m (20 ft)