Yamaha MOX8 Owner's Manual - Page 64
Sound is cut off., Only one note sounds at a time., Pitch or intervals are wrong., No effect is
UPC - 086792950907
View all Yamaha MOX8 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 64 highlights
Appendix Are the filter settings appropriate? Excessively high filter resonance settings can cause distortion. [VOICE] [EDIT] Element/Key selection [F3] FILTER [PERFORM] [EDIT] Part selection [F4] TONE [SF1] FILTER [SONG]/[PATTERN] [MIXING] [EDIT] Part selection [F4] TONE [SF1] FILTER [SONG]/[PATTERN] [UTILITY] [F2] SEQ [SF2] FILTER Are any of the following volume parameters set so high that clipping is occurring? [UTILITY] [F1] GENERAL [SF1] TG "Volume" [VOICE] [EDIT] [COMMON] [F2] OUTPUT Volume [VOICE] [EDIT] Element/Key selection [F4] AMP [SF1] LVL/PAN "Level" [PERFORM] [EDIT] [COMMON] [F2] OUT/MFX [SF1] OUT "Volume" [PERFORM] [EDIT] Part selection [F2] OUTPUT [SF1] VOL/PAN "Volume" [SONG]/[PATTERN] [MIXING] [EDIT] Part selection [F2] OUTPUT [SF1] VOL/PAN "Volume" Sound is cut off. Is the entire amount of notes played (via your keyboard playback and Song/Pattern/Arpeggio playback) exceeding the maximum polyphony of this instrument? Only one note sounds at a time. When this situation occurs, the Mono/Poly parameter in the current mode is set to "mono." If you wish to play chords, set this parameter to "poly." [VOICE] [F4] PORTA "Mono/Poly" [PERFORM] [EDIT] Part selection [F1] VOICE [SF2] MODE "Mono/Poly" [SONG]/[PATTERN] [MIXING] [EDIT] Part selection [F1] VOICE [SF2] MODE "Mono/Poly" Pitch or intervals are wrong. Is the Master Tune parameter in the Utility mode set to a value other than "0"? [UTILITY] [F1] GENERAL [SF1] TG "Tune" Is the Note Shift parameter in the Utility mode set to a value other than "0"? [UTILITY] [F1] GENERAL [SF1] TG "NoteShift" When the Voice produces a wrong pitch, is the appropriate tuning system selected from Micro Tuning parameter in the Voice Edit mode? [VOICE] [EDIT] [COMMON] [F1] GENERAL [SF2] PLY MODE "M. Tuning No." When the Voice produces a wrong pitch, is the LFO Pitch Modulation Depth in the Voice Edit mode set too high? [VOICE] [EDIT] Element/Key selection [F5] LFO "PMod" When the Performance/Song/Pattern produces a wrong pitch, are the Note Shift and Detune parameters of each Part set to a value other than "0"? [PERFORM] [EDIT] Part selection [F4] TONE [SF1] TUNE [SONG]/[PATTERN] [MIXING] [EDIT] Part selection [F4] TONE [SF1] TUNE When the Song/Pattern playback produces a wrong pitch, is the Note Offset parameter in the Groove display set to a value other than "0"? [SONG]/[PATTERN] [F2] GROOVE "NOTE OFST" No effect is applied. Check the on/off status of the EFFECT [INSERTION]/[SYSTEM]/[MASTER] button. Is the Reverb Send or Chorus Send set to a value other than "0"? [VOICE] [EDIT] [COMMON] [F2] OUTPUT "ChoSend" / "RevSend" [PERFORM] [EDIT] [COMMON] [F2] OUT/MFX [SF1] OUT "ChoSend" / "RevSend" [SONG]/[PATTERN] [MIXING] [EDIT] Part selection [F2] OUTPUT [SF1] VOL/PAN "ChoSend" / "RevSend" Have any or all of the Elements' Insertion Effect Output parameters been set to "thru" in the effect setting display in the Voice Edit mode? [VOICE] [F6] EFFECT [SF1] CONNECT "EL: OUT 1-8" 64 MOX6/MOX8 Owner's Manual