Yamaha MX-1 Owner's Manual
Yamaha MX-1 Manual
 |
View all Yamaha MX-1 manuals
Add to My Manuals
Save this manual to your list of manuals |
Yamaha MX-1 manual content summary:
- Yamaha MX-1 | Owner's Manual - Page 1
MX-1 MX-2 Natural Sound Stereo Power Amplifier CONTENTS Safety Instructions 2 Features 3 Connections 4 Control Parts and Their Functions 6 Troubleshooting 7 Specifications 8 OWNER'S MANUAL - Yamaha MX-1 | Owner's Manual - Page 2
unit has been dropped, or the cabinet damaged. 16 Servicing - The user should not attempt to service the unit beyond those means described in the operating instructions. All other servicing should be referred to qualified service personnel. 17 Power Lines - An outdoor antenna should be located away - Yamaha MX-1 | Owner's Manual - Page 3
% THD, 20-20,000 Hz : 150W + 150W (8Ω) RMS Output Power, 0.008% THD, 20-20,000 Hz q Increased Low Impedance Drive Capability q 2-Pair Speaker Drive Capability q REMOTE CONTROL Connector to Make the Power of This Unit Controlled by the Pre-Amplifier CX-1 or CX-2 q Gold-Plated Input Terminals 3 - Yamaha MX-1 | Owner's Manual - Page 4
first switch OFF the power to this unit and the owner's manual for each component to be connected to this unit. Speakers A Pre-amplifier etc. REMOTE MX-2> Pre-amplifier etc. REMOTE CONTROL PRE OUT Speakers B Speakers A Right LEVEL Left (U.S.A. model) INPUT REMOTE CONTROL ( PRE AMP - Yamaha MX-1 | Owner's Manual - Page 5
parts of this unit, this unit and/or speakers could be damaged. To prevent speaker wires from coming loose, make sure wire holders are firmly screwed in. REMOTE CONTROL (PRE AMP) connector If you have the YAMAHA pre-amplifier CX-1 or CX-2, connect this connector to the REMOTE CONTROL (POWER AMP - Yamaha MX-1 | Owner's Manual - Page 6
mode (For Europe model only) If the REMOTE CONTROL (PRE AMP) connector on the rear panel of this unit is connected to the corresponding connector of the pre-amplifier (CX-1 or CX-2), by turning the power off with the POWER switch of the pre-amplifier, this unit is switched to the STANDBY mode. (In - Yamaha MX-1 | Owner's Manual - Page 7
cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service center for help. SYMPTOM The unit fails to turn on when the POWER switch is pressed. No sound. The sound suddenly goes off. No sound is heard from - Yamaha MX-1 | Owner's Manual - Page 8
-A Network) MAIN IN (Input Shorted) < > MX-1 125 dB < > MX-2 123 dB Residual Noise (IHF-A Network 20 µV Channel Separation (Vol. -30 dB) MAIN IN (Input 5.1 k-ohms Terminated 1 kHz/10 kHz 80 dB/60 dB Power Supply [U.S.A. and Canada models AC 120V, 60 Hz [Australia and U.K. models AC 240V, 50 Hz
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
 |
 |
OWNER’S MANUAL
MX-1
MX-2
Natural Sound Stereo Power Amplifier
CONTENTS
Safety Instructions
.....................
2
Features
...................................
3
Connections
.............................
4
Control Parts and Their
Functions
.................................
6
Troubleshooting
........................
7
Specifications
...........................
8