Yamaha NS-P30 Owner's Manual

Yamaha NS-P30 Manual

Get Yamaha NS-P30 PDF manuals and user guides View all Yamaha NS-P30 manuals
Add to My Manuals
Save this manual to your list of manuals

Yamaha NS-P30 manual content summary:

  • Yamaha NS-P30 | Owner's Manual - Page 1
    Yamaha NS-P30 speaker system. "NS-P30" is the package number which includes the YAMAHA speaker systems NX-E70 and NX-C70. NX-E70 is designed to be used as an effect speaker system, and NX the same shelf or rack as the turntable can result in feedback. ● As these speakers contain
  • Yamaha NS-P30 | Owner's Manual - Page 2
    of the speaker by using the provided screws. Wall/ wall support 2 Fasten screws into a firm wall or wall support as shown in the diagram, and hang the holes of resulting from tripping over loose speaker cables, fix them to the wall. s NX-C70 Place the speaker on top of the TV or on the floor under
  • Yamaha NS-P30 | Owner's Manual - Page 3
    cm (3-1/8") full range speaker Frequency Range NX-C70 100 - 20,000 Hz NX-E70 110 - 20,000 Hz Sound Pressure Level NX-C70 85.0 dB NX-E70 85.0 dB Maximum Power Handling Capacity NX-C70 27W NX-E70 13.5W Impedance NX-C70 8 ohms NX-E70 4 ohms Dimensions (W x H x D) NX-C70 280 x 123 x 140 mm (11
  • Yamaha NS-P30 | Owner's Manual - Page 4
    ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
  • 1
  • 2
  • 3
  • 4
1
NS-P30
Thank you for selecting this Yamaha NS-P30 speaker system.
“NS-P30” is the package number which includes the
YAMAHA speaker systems NX-E70 and NX-C70.
NX-E70 is designed to be used as an effect speaker system,
and NX-C70 is designed to be used as a center speaker
system.
PRECAUTIONS
Read these precautions carefully before using your speaker.
●
Any time you note distortion, reduce the volume control on
your amplifier to a lower setting. Never allow your amplifier to
be driven into “clipping”. Otherwise the speaker may be
damaged.
●
When using an amplifier with a rated output power higher than
the nominal input power of the speaker, care should be taken
never to exceed the speaker’s maximum input.
●
Do not attempt to clean the speaker with chemical solvents as
this might damage the finish. To clean, wipe with a dry, soft
cloth.
●
To prevent the enclosure from warping or discoloring, do not
place the speaker where it will be exposed to direct sunlight or
excessive humidity.
●
Do not place the speaker where it is liable to be knocked over
or struck by falling objects. Stable placement will also ensure
better sound performance.
●
Placing the speaker on the same shelf or rack as the turntable
can result in feedback.
●
<
For NX-E70 only
>
As these speakers contain strong magnets, avoid placing
watches, magnetic tapes, etc. near them. Also, placing the
speakers near a TV set may impair picture color. If this
happens, move the TV set away from the speakers.
●
Secure placement or installation is the owner’s
responsibility.
YAMAHA shall not be liable for any accident caused by
improper placement or installation of the speaker.
BEFORE MAKING CONNECTIONS, MAKE SURE THAT THE
AMPLIFIER IS SWITCHED OFF.
■
NX-E70
●
Connect the push-type input terminals at the rear of the
speakers to the speaker output terminals (for effect speakers)
of your amplifier (or receiver) with the provided speaker
cables.
●
One side of the speaker cable has a white line and the other
side has no line. Connect the (+) terminals on both the
amplifier (or receiver) and the speakers using the side with a
white line. Connect the (–) terminals on both components
using the side with no line.
●
Connect one speaker to the left (marked L) terminals of your
amplifier (or receiver), and another speaker to the right
(marked R) terminals, making sure not to reverse the polarity
(+, –). If one speaker is connected with reversed polarity, the
sound will be unnatural and lack bass.
Procedures:
Press the tab on the terminal down, as shown in the figure.
Insert the bare speaker wire end properly into the terminal
hole. [Remove approx. 5 mm (1/4”) insulation from the
speaker cable.]
Remove your finger from the tab to allow it to lock snugly on
the cable’s wire end.
Test the security of the connection by tugging lightly on the
cable at the terminal.
■
NX-C70
To connect the speaker cable from NX-C70 to the speaker
output terminals (for a center speaker) on the amplifier (or
receiver), make sure to connect the side with a white line to the
(+) terminal and the side with no line to the (–) terminal.
Note
Do not let the bare speaker wires touch each other as this
could damage the speaker and/or the amplifier.
CONNECTION TO YOUR AMPLIFIER
R
L
REAR
CENTER
REAR
SPEAKERS
CENTER/REAR
L
R
White line
White line
Amplifier or receiver
NX-C70 (Center speaker)
NX-E70
(Effect speaker)