Yamaha P7000S Owner's Manual

Yamaha P7000S - Amplifier Manual

Get Yamaha P7000S - Amplifier PDF manuals and user guides
UPC - 086792658940
View all Yamaha P7000S manuals
Add to My Manuals
Save this manual to your list of manuals

Yamaha P7000S manual content summary:

  • Yamaha P7000S | Owner's Manual - Page 1
    POWER AMPLIFIER Owner's Manual E
  • Yamaha P7000S | Owner's Manual - Page 2
    SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE servicing) instructions in the literature accompanying the product. IMPORTANT SAFETY INSTRUCTIONS 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use the power cord from
  • Yamaha P7000S | Owner's Manual - Page 3
    WARNING Installation ● Connect this unit's power cord only to an AC outlet of the type stated in this Owner's Manual or as marked on the unit. the power switch off, remove the power plug from the AC outlet, and contact your dealer. If you continue using the unit without heeding this instruction, fi
  • Yamaha P7000S | Owner's Manual - Page 4
    respective owners. FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use
  • Yamaha P7000S | Owner's Manual - Page 5
    unit is running hot. • Variable-speed low-noise fans ensure high reliability. This Owner's Manual covers the four models: P7000S, P5000S, P3500S and P2500S power amplifiers. Please read through this manual carefully before beginning use, so that you will be able to take full advantage of the amplifier
  • Yamaha P7000S | Owner's Manual - Page 6
    seconds at time of power-on, as the amp gets ready to operate. problem is corrected, the indicator goes off and normal operation resumes. 4 CLIP indicator Lights up red when the output signal distortion on the corresponding channel to install the security cover (1) Use the supplied hex wrench to
  • Yamaha P7000S | Owner's Manual - Page 7
    : This feature provides improved frequency reponse on speakers such as the YAMAHA S112 and S115. 3 INPUT jacks (Channels A, B) Two jack types are provided for each channel. Note that if you are using BRIDGE or PARALLEL mode, only the Channel A jacks are effective. • XLR-3-31 jack The XLR-3-31 input
  • Yamaha P7000S | Owner's Manual - Page 8
    switch Use this switch to select the operating mode. • STEREO mode Channels A and B operate independently (as with a conventional stereo amplifier). The Channel A input goes to the Channel A output jacks, and the Channel B input goes to the Channel B output jacks. • PARALLEL mode The Channel A input
  • Yamaha P7000S | Owner's Manual - Page 9
    the number of speakers. Please be sure that your speakers' impedance is not less than the relevant minimum value indicated below. Connection configurations for STEREO and PARALLEL modes When using 5-way binding post output jacks Connection configurations for BRIDGE mode When
  • Yamaha P7000S | Owner's Manual - Page 10
    size Note to users in the USA: Please use Class 3 wiring. (P7000S, P5000S) Please use Class 2 wiring. (P3500S, P2500S) Be sure CHANNEL A STEREO or PARALLEL BRIDGE 1+ A+ 1+ + 1- A- 1- 2+ B+ 2+ - 2- B- 2- Neutrik NL4FC plugs CHANNEL B 1+ B+ 1- B- Phone jack (1) Turn off the POWER
  • Yamaha P7000S | Owner's Manual - Page 11
    Rack Mounting Mounting in a standard EIA rack If you are mounting multiple power amplifiers in a rack, be sure to install ventilation panel(s) as shown below. Also be sure to use metal brackets (one on each side) to support the rear of each amplifer. Note: EIA stands for Electronic Industries
  • Yamaha P7000S | Owner's Manual - Page 12
    60 Hz:7 kHz, 4:1, Half Power 4 Ω - 8 Ω/STEREO 8 Ω/BRIDGE ≤ 0.1 % Channel Separation Vol. max Half Power RL = 8 Ω 1 kHz Owner's Manual 0 dBu=0.775 Vrms, Half Power=1/2 Power Output Level (Rated Power) Specifications and descriptions in this owner's manual are for information purposes only. Yamaha
  • Yamaha P7000S | Owner's Manual - Page 13
    Hz-150 Hz] ON OFF YAMAHA SPEAKER PROCESSING INV YAMAHA SPEAKER PROCESSING Limiter Ach Power Amp CLIP Temperature Sensor (Heat Sink) Protection Circuit CLIP CHANNEL B PARALLEL Bch Power Amp BA OFF ATT State variable BRIDGE Limiter Active filter STEREO LPF HPF Frequency [25 Hz-150
  • Yamaha P7000S | Owner's Manual - Page 14
    ■ Dimensions ■ Current Draw P7000S standby idle 1/8 power 8Ω/ch 4Ω/ch 1/3 power 8Ω/ch 4Ω/ch P5000S standby idle 1/8 power 8Ω/ch 4Ω/ch 1/3 power 8Ω/ch 4Ω/ch P3500S standby idle 1/8 power 8Ω/ch 4Ω/ch 1/3 power 8Ω/ch 4Ω/ch Line Current (A) 100/120V 230/240V 0.08 0.04 1.0
  • Yamaha P7000S | Owner's Manual - Page 15
    amplifier's output circuit. Consult your dealer or the nearest Yamaha service center. The relay operates to protect the speaker system. P7000S, P5000S Indicator(s) Possible Cause Remedy Protection Circuit Power has been shut down. (All indicators are off.) A DC voltage of ± 2 V or greater
  • Yamaha P7000S | Owner's Manual - Page 16
    430-8650 Tel: +81-53-460-2441 Yamaha Pro Audio global web site http://www.yamahaproaudio.com/ Yamaha Manual Library http://www.yamaha.co.jp/manual/ U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation © 2003 Yamaha Corporation WB09700 001CRZCx.x-xxE0 Printed in Indonesia
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
POWER AMPLIFIER
Owner’s Manual
E