Yamaha PSR-S650 Owner's Manual - Page 57

Saving the Registration Memory

Get Yamaha PSR-S650 PDF manuals and user guides View all Yamaha PSR-S650 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

9. Using USB Flash Memory Saving the Registration Memory All 64 setups memorized to the Registration Memory can be saved to the USB flash memory as a single file (extension: usr). 1 Make sure that a formatted USB flash memory has been properly connected to the USB TO DEVICE terminal, then call up the FILE CONTROL display (page 55). 2 Use the CATEGORY [] buttons to select "Regist Save." A default file name will automatically be created. Cursor left Cursor right Delete character Select characters Cursor Regist Save To Overwrite an Existing File If you want to overwrite a file that already exists in USB flash memory, use the dial or the [-/NO] and [+/YES] buttons to select the file, then go to step 5. NOTE • If there is not enough capacity left in the USB flash memory, a message will appear in the display and you cannot save the data. Erase unnecessary files from the USB flash memory to make more memory available (page 60). 3 Press the [EXECUTE] button. A cursor will appear below the first character in the file name. 4 Change the file name as necessary. • The [1] button moves the cursor to the left, and the [2] button moves it to the right. • Use the dial to select a character for the current cursor location. • The [8] button deletes the character at the cursor location. 5 Press the [EXECUTE] button. The display prompts you for confirmation. You can cancel the save operation at this message by pressing the [-/NO] button. 6 Press the [EXECUTE] button again, or the [+/YES] button to execute the save operation. NOTICE • The amount of time it may take to perform the save operation depends on the status of the USB flash memory. Even if this takes a long time, never turn off the power or remove the USB flash memory during this operation. Doing so could result in damage to the data. NOTE • If an existing file name is specified, the display prompts you for confirmation. Press [EXECUTE] or [+/YES] if it is OK to overwrite the file, or [-/NO] to cancel. 7 When the operation is complete, a "Completed" message appears briefly, then returns to the display of step 2. Press the [EXIT] button to exit from the FILE CONTROL display. The Registration Memory file will be saved to the USER FILE folder in the USB flash memory. NOTE • Perform the Load operation (page 59) if you want to recall the Registration Memory file on the USB flash memory to the instrument. Owner's Manual 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
Owner’s Manual
57
9. Using USB Flash Memory
All 64 setups memorized to the Registration Memory
can be saved to the USB flash memory as a single file
(extension: usr).
1
Make sure that a formatted USB flash
memory has been properly connected
to the USB TO DEVICE terminal, then
call up the FILE CONTROL display
(page 55).
2
Use the CATEGORY [
<
] and [
>
] buttons
to select “Regist Save.”
A default file name will automatically be created.
3
Press the [EXECUTE] button.
A cursor will appear below the first character in
the file name.
4
Change the file name as necessary.
•
The [1] button moves the cursor to the left, and
the [2] button moves it to the right.
•
Use the dial to select a character for the current
cursor location.
•
The [8] button deletes the character at the cur-
sor location.
5
Press the [EXECUTE] button.
The display prompts you for confirmation. You
can cancel the save operation at this message by
pressing the [-/NO] button.
6
Press the [EXECUTE] button again, or
the [+/YES] button to execute the save
operation.
7
When the operation is complete, a “Com-
pleted” message appears briefly, then
returns to the display of step 2. Press the
[EXIT] button to exit from the FILE CON-
TROL display.
The Registration Memory file will be saved to the
USER FILE folder in the USB flash memory.
Saving the Registration Memory
To Overwrite an Existing File
If you want to overwrite a file that already exists
in USB flash memory, use the dial or the [-/NO]
and [+/YES] buttons to select the file, then go to
step 5.
• If there is not enough capacity left in the USB flash
memory, a message will appear in the display and you
cannot save the data. Erase unnecessary files from the
USB flash memory to make more memory available
(page 60).
Regist Save
NOTE
• The amount of time it may take to perform the save
operation depends on the status of the USB flash
memory. Even if this takes a long time, never turn off
the power or remove the USB flash memory during
this operation. Doing so could result in damage to the
data.
• If an existing file name is specified, the display prompts
you for confirmation. Press [EXECUTE] or [+/YES] if it is
OK to overwrite the file, or [-/NO] to cancel.
• Perform the Load operation (page 59) if you want to
recall the Registration Memory file on the USB flash
memory to the instrument.
Cursor
left
Cursor
right
Delete
character
Select characters
Cursor
NOTICE
NOTE
NOTE