Yamaha RX-A800 Quick Reference Guide
Yamaha RX-A800 Manual
 |
View all Yamaha RX-A800 manuals
Add to My Manuals
Save this manual to your list of manuals |
Yamaha RX-A800 manual content summary:
- Yamaha RX-A800 | Quick Reference Guide - Page 1
for connection Speakers Ex. Front speaker Ex. Center speaker Ex. Surround speaker, surround back speaker, and presence speaker Ex. Active subwoofer • Use speakers with an impedance of at least 6Ω. 4Ω speakers can also be used as the front speakers. For more information on speaker impedance - Yamaha RX-A800 | Quick Reference Guide - Page 2
L Center speaker Surround 1 speaker L Front speaker R Subwoofer 1 Surround speaker R 6.1 Surround back speaker 7.1 Surround back speaker L 7.1 Surround back speaker R 1 Connect the speakers 7.1 Connect when using with 7.1-channel speaker layout. Place the surround back speakers (L/R) 12 - Yamaha RX-A800 | Quick Reference Guide - Page 3
the terminal. 4 Tighten the terminal. Connecting the subwoofer 1 Connect the subwoofer input jack to the SUBWOOFER 1 or 2 jack on this unit with an audio pin cable. 2 Set the subwoofer volume as follows. Volume: Set to approximately half volume (or slightly less than half). Crossover frequency (if - Yamaha RX-A800 | Quick Reference Guide - Page 4
operations carried out on the TV, and that makes TV sound control easier to use. For the connections and settings, refer to "Using the HDMI Control function" in the Owner's Manual. When using a TV that supports HDMI Control functions When HDMI Control functions are enabled on the unit, input source - Yamaha RX-A800 | Quick Reference Guide - Page 5
and audio from analog output jacks. Refer to "Connecting external components" in the Owner's Manual for details. 4 Connect the AC power cable RS-232C SURROUND BACK/ SPEAKERS EXTRA SP BI-AMP ZONE2/PRESENCE SINGLE SINGLE CENTER SUR.BACK PRE OUT 1 SUBWOOFER 2 To the power outlet AC power - Yamaha RX-A800 | Quick Reference Guide - Page 6
in the Owner's Manual. VOLUME CROSSOVER/ HIGH CUT MIN MAX MIN MAX Subwoofer examples YPAO microphone 3 Press RECEIVER A on the remote control to switch this unit on. 4 Connect the YPAO microphone to the YPAO MIC jack on the front panel. MAIN ZONE INPUT ZONE2 ZONE CONTROL INFO MEMORY - Yamaha RX-A800 | Quick Reference Guide - Page 7
Owner's Manual to resolve the problem and measure acoustics with YPAO again. 6 Use the cursor C to select "Save/Exit" and press ENTER. 7 Use the cursor D/E to select "SAVE" and press ENTER. When the display at left appears, the YPAO setup is complete. MAIN ZONE 2 CODE SET SOURCE RECEIVER HDMI - Yamaha RX-A800 | Quick Reference Guide - Page 8
channels. © 2010 Yamaha Corporation - 8 - A MAIN ZONE 2 CODE SET SOURCE RECEIVER HDMI 1 2 3 4 AUDIO 5 V-AUX 1 2 AV 1 2 3 4 B 5 6 TUNER SIRIUS CATEGORY FM AM INFO MEMORY MULTI [ A ] DOCK HDMI OUT PRESET TUN./CH F MOVIE ENHANCER SUR. DECODE MUSIC SLEEP PARTY
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
 |
 |
PUSH
1
3
2
within 20 feet (6 m)
- 1 -
English
Quick Reference Guide
for U.S.A.
Ex.
Ex.
Preparing the remote control
■
Accessories
■
Items necessary for connection
The following accessories are supplied with this product.
Speakers
External components
Remote control
Front speaker
Ex.
Ex.
Batteries (2)
(AAA, R03, UM-4)
Center speaker
AM loop antenna
Surround speaker, surround back
speaker, and presence speaker
Indoor FM antenna
VIDEO AUX input cover
Active subwoofer
YPAO microphone
1
Take off the battery compartment cover.
2
Insert the two supplied AAA batteries
into the battery case, following the
polarity markings.
3
Snap the battery compartment cover
back into place.
Be sure to aim the remote control directly at the remote
control sensor on this unit during operation.
TV
Cable
• Cables for connecting external components
(may differ depending on the components you are connecting)
• Speaker cables
(a quantity to match the number of speakers you are connecting)
• Audio pin cable
(for subwoofer)
Playback device such as
BD (Blu-ray Disc)/DVD players
•
Use speakers with an impedance of at least 6Ω. 4Ω speakers can also be used as the front speakers. For more information on speaker
impedance, refer to page 3.
•
If you are using a CRT monitor, we recommend that you use magnetically shielded speakers.
•
Prepare at least two front speakers. The priority of the other speakers is as follows:
1
Two surround speakers
2
One center speaker
3
One (or two) surround back speaker (s)/presence speakers