Yamaha RXV465 Owner's Manual - Page 56

After Auto Setup, E-5:noisy, E-6:check Sur., E-7:no Mic, E-8:no Signal, E-9:user Cancel

Get Yamaha RXV465 - RX AV Receiver PDF manuals and user guides
UPC - 027108933214
View all Yamaha RXV465 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Troubleshooting Error message E-5:NOISY Cause Measurement cannot be performed accurately due to loud ambient noise. E-6:CHECK SUR. E-7:NO MIC E-8:NO SIGNAL Surround back speakers are connected, though surround L/R speakers are not. The optimizer microphone was unplugged during the "Auto Setup" procedure. The optimizer microphone does not detect test tones. E-9:USER CANCEL "Auto Setup" was cancelled due to an inappropriate user operation. E-10:INTERNAL ERROR An internal error occurred. Remedy Try running "Auto Setup" in a quiet environment. Turn off noisy electric equipment like air conditioners or move them away from the optimizer microphone. When using surround back speakers, you need to connect surround L/R speakers. Do not touch the optimizer microphone during "Auto Setup." Check whether the microphone is properly placed. Check whether the speakers are properly placed and connected. The optimizer microphone or OPTIMIZER MIC jack may be defective. Contact the nearest Yamaha dealer or service center. Run "Auto Setup" again. Run "Auto Setup" again. See page - - 11 18 18 11 18 18 18 After Auto Setup Error message Cause Remedy W-1:OUT OF PHASE Speaker polarity is not correct. This message may appear depending on the speakers even when the speakers are connected correctly. Check the polarities (+, -) of the displayed speaker. If they are correct, the speakers work properly even when this message is displayed. W-2:OVER 24m (80ft) The distance between the speaker and the Bring the speaker within 24 m (80 ft.) area around listening position is over 24 m (80 ft). the listening position. W-3:LEVEL ERROR The difference of volume level among speakers is excessive. Recheck the speaker positions and make sure all speakers are placed in a similar environment. Check the polarities (+, -) of the speakers. We recommended that you use speakers with the same or similar specifications. Adjust the output volume of the subwoofer. If a warning message related to the surround back speaker is displayed, the volume or right and left balance of the external amplifier may not be properly set. Check if the volume or balance of the external amplifier is proper. See page 11 - - 11 - - - 52 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
52
En
Troubleshooting
E-5:NOISY
Measurement cannot be performed
accurately due to loud ambient noise.
Try running “Auto Setup” in a quiet environment.
—
Turn off noisy electric equipment like air
conditioners or move them away from the optimizer
microphone.
—
E-6:CHECK SUR.
Surround back speakers are connected,
though surround L/R speakers are not.
When using surround back speakers, you need to
connect surround L/R speakers.
11
E-7:NO MIC
The optimizer microphone was
unplugged during the “Auto Setup”
procedure.
Do not touch the optimizer microphone during “Auto
Setup.”
18
E-8:NO SIGNAL
The optimizer microphone does not
detect test tones.
Check whether the microphone is properly placed.
18
Check whether the speakers are properly placed and
connected.
11
The optimizer microphone or OPTIMIZER MIC
jack may be defective. Contact the nearest Yamaha
dealer or service center.
18
E-9:USER CANCEL
“Auto Setup” was cancelled due to an
inappropriate user operation.
Run “Auto Setup” again.
18
E-10:INTERNAL ERROR
An internal error occurred.
Run “Auto Setup” again.
18
After Auto Setup
Error message
Cause
Remedy
See
page
W-1:OUT OF PHASE
Speaker polarity is not correct. This
message may appear depending on the
speakers even when the speakers are
connected correctly.
Check the polarities (+, –) of the displayed speaker.
If they are correct, the speakers work properly even
when this message is displayed.
11
W-2:OVER 24m (80ft)
The distance between the speaker and the
listening position is over 24 m (80 ft).
Bring the speaker within 24 m (80 ft.) area around
the listening position.
—
W-3:LEVEL ERROR
The difference of volume level among
speakers is excessive.
Recheck the speaker positions and make sure all
speakers are placed in a similar environment.
—
Check the polarities (+, –) of the speakers.
11
We recommended that you use speakers with the
same or similar specifications.
—
Adjust the output volume of the subwoofer.
—
If a warning message related to the
surround back speaker is displayed, the
volume or right and left balance of the
external amplifier may not be properly
set.
Check if the volume or balance of the external
amplifier is proper.
—
Error message
Cause
Remedy
See
page