Yamaha V3.8 DME Designer V3.8 DME Setup Manual
Yamaha V3.8 Manual
View all Yamaha V3.8 manuals
Add to My Manuals
Save this manual to your list of manuals |
Yamaha V3.8 manual content summary:
- Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 1
about the DME Designer application refer to the pdf-format DME Designer manual. n If you will be using CobraNet™ for audio connections, the (this does not apply to the SP2060 or ICP1). Contact your Yamaha dealer or service center for this type of upgrade. • DME Designer cannot be used to downgrade - Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 2
web site on DME series and peripherals This section serves as a guide to online information on Speaker Processor Components library data, Mini-YGDAI cards, and touch-panel controllers (AMX/Creston). DME-N Network Driver Setup Details (page 23) Troubleshooting & Tips (page 26) DME Setup Manual 2 - Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 3
and download the appropriate driver for your computer's operating system. n DME Designer V3.8 supports Windows7, Windows Vista, and Windows XP. Minimum System Requirements OS Hard Disk Display Other MIDI Driver V3.0.4 or later, and DME-N Network Driver V1.2.1 or later. DME Setup Manual 3 - Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 4
folder in an easy-to-find location such as your desktop. Then, follow the steps described below in order to install the software. DME Setup Manual 4 - Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 5
necessary to restart the computer after the new software has been installed. Follow the on-screen instructions. USB-MIDI Driver Installation 1 Disconnect all USB devices from the computer except for the the "User Account Control" window appears, click [Continue] or [Yes]. DME Setup Manual 5 - Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 6
by following the on-screen directions. n This display will not appear when using Windows XP x64/Windows Vista/Windows 7. No restart is necessary. DME Setup Manual Software Installation 6 - Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 7
of the display (in this case a DME24N), or select a DME unit and drag-and-drop it into the designer window. Drag and drop DME Setup Manual 7 - Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 8
...] 2-2 In the DME Device Properties window that is displayed, select the currently-inserted expansion card as shown below and click the [OK] button. DME Setup Manual 8 - Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 9
connected in the same way, as shown in the example below, next, create a scene and transmit the setup data to the DME unit. DME Setup Manual 9 - Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 10
is installed, check that the DME unit is properly connected to the computer. 5-3 Click the [On-line] button from the Main Panel window. DME Setup Manual 10 - Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 11
then click the [OK] button. 5-7 In response to the prompt, "Synchronizing will cause audio to mute. Is this OK?", click the [Yes] button. DME Setup Manual 11 - Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 12
input volume to a suitable level. Specifically, it is recommended that the level shown by the input meter be peaking at around -18 dB. DME Setup Manual Basic Setup 12 - Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 13
units, set Link Mode on each unit to the same setting. Yamaha recommends that you select 100Base-TX for the Link Mode setting. DME Setup Manual 13 - Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 14
display (page 21). ICP1 settings can be made via the unit's control panel. Refer to "ICP1 settings and operation" of the DME Designer V3.8 Owner's Manual. 1 Connect the computer to the DME unit via a USB cable, then turn the DME unit power ON. USB cable 2 Click the [Communication Port] button from - Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 15
is output due to group settings not yet having been made.) Slave settings (DME8o-C in the example). Slave settings (DME64N in the example). DME Setup Manual 15 - Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 16
]. The "Local Area Connection Status" dialog box will be displayed n If the "Local Area Connection properties" dialog box appears, skip ahead to step 5. DME Setup Manual 16 - Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 17
have been made, connect the DME units and computer via a switching hub using Ethernet cables, as shown in the example on page 13. DME Setup Manual 17 - Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 18
Settings] button to open the "Advanced Settings" dialog box. DME devices connected to the network can be automatically detected via this dialog box. DME Setup Manual n If the IP address was not automatically detected, register the DME device - Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 19
are displayed collectly, and then click the [Go On-Line] button. Check sound output as described in the Basic Setup section (page 12). DME Setup Manual 19 - Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 20
connection to the DME unit, please refer to the owner's manual that came with the control panel. Connection via Ethernet Intelligent Control terminals, there may be a problem with the DME settings. If there is no problem with the DME settings there may be a problem with the DME unit itself. Maximum - Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 21
unit must be assigned as the master in each device group. All other DME units in the group should be set to slave. DME Setup Manual 21 - Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 22
information on touch panel controllers by other manufacturers, visit: AMX's web site: http://www.amx.com/ CRESTRON's web site: http://www.crestron.com/ DME Setup Manual 22 - Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 23
communication with the device will not be possible. n The Device MAC Address setting cannot be changed for the device connected to the network. DME Setup Manual 23 - Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 24
provides access to advanced settings. For details refer to the "Advanced Settings" dialog box in the next section. DME-N Network Driver Setup Details DME Setup Manual 24 - Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 25
in a different environment. Click to open the "Save As" dialog. Enter a file name and click the [Save] button to save the setup file. DME Setup Manual 25 - Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 26
Troubleshooting & Tips Problem Possible cause Corrective action Download and install the most up-to-date USB-MIDI driver from up-to-date version supported by DME. the Yamaha website (http://www.yamahaproaudio.com/) The MIDI port setting is selected from its context menu. DME Setup Manual 26 - Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 27
Troubleshooting & Tips Problem The message "Reset Config..." is displayed for a long time in until the firmware is reinstalled. For details regarding initialization, please refer to the Owner's Manual that came with your DME device(s). Specifically, this information can be found in the section - Yamaha V3.8 | DME Designer V3.8 DME Setup Manual - Page 28
Troubleshooting & Tips Uninstall the USB-MIDI Driver Windows XP 1 Disconnect all Account Control" window appears, click [Allow] or [Continue]. A dialog box appears. Follow the instructions to remove the software. DME Setup Manual U.R.G., Pro Audio Division © 2010 Yamaha Corporation 010MW-A0 28
DME Setup Manual
1
Version 3.8
This manual describes the process of setting up a DME system, from making the initial DME processor
settings (DME64N / DME24N / DME8i-C / DME8o-C / DME4io-C / DME8i-ES / DME8o-ES / DME4io-ES) to
synchronizing with the DME Designer application installed on a computer.
n
In this document the term “DME” will refer to the DME64N, DME24N, DME8i-C, DME8o-C, DME4io-C, DME8i-ES, DME8o-ES
and DME4io-ES, while the term “DME Satellite” will refer only to the DME8i-C, DME8o-C, DME4io-C, DME8i-ES, DME8o-ES and
DME4io-ES.
n
For details about the DME units refer to the manual supplied with the specific device, and for details about the DME Designer
application refer to the pdf-format DME Designer manual.
n
If you will be using CobraNet™ for audio connections, the required bundle numbers and related settings must be made via the
DME Designer application.
n
If you will be using EtherSound™ for audio connections, the routing and other EtherSound settings must be made via the
AuviTran AVSESMonitor software available from the AuviTran website:
•
DME Designer cannot be used to upgrade DME firmware version 3.5 or earlier to version 3.8 or later (this
does not apply to the SP2060 or ICP1). Contact your Yamaha dealer or service center for this type of
upgrade.
•
DME Designer cannot be used to downgrade DME firmware version 3.8 or later to version 3.5 or earlier
(this does not apply to the SP2060 or ICP1). Contact your Yamaha dealer or service center for this type of
downgrade.
•
DME firmware versions 3.8 or later cannot be written using DME Designer version 3.5 or earlier.
•
When DME units running firmware version 3.5 or earlier and DME or DME Satellite units running firmware
versions 3.8 or later are combined in the same device group, DME units running firmware version 3.5 or
earlier cannot be designated as the group master.
Version Compatibility
DME Setup Manual
DME Setup Manual