ZyXEL ONU-6040B-22 User Guide
ZyXEL ONU-6040B-22 Manual
 |
View all ZyXEL ONU-6040B-22 manuals
Add to My Manuals
Save this manual to your list of manuals |
ZyXEL ONU-6040B-22 manual content summary:
- ZyXEL ONU-6040B-22 | User Guide - Page 1
ONU-6040BF-2x Series User's Guide GEPON Optical Network Unit Version 1.00 Edition 1, 5/2009 www.zyxel.com C 2009 ZyXEL Communications Corporation - ZyXEL ONU-6040B-22 | User Guide - Page 2
ENGLISH 2 - ZyXEL ONU-6040B-22 | User Guide - Page 3
Terminal). Once you have connected the hardware, you are ready to enjoy Internet access. Two ONU-6040BF-2x models are discussed in this guide: ONU-6040BF-21 (with a 10km transceiver) and ONU-6040BF-22 (with a 20km transceiver). Hardware Connections 1. PON: Follow the steps below to connect an SC - ZyXEL ONU-6040B-22 | User Guide - Page 4
a. Hold the ONU-6040BF-2x upright, push the top cover forward with the LEDs (lights) facing you, then lift up the top cover to remove it. 4 - ZyXEL ONU-6040B-22 | User Guide - Page 5
5 - ZyXEL ONU-6040B-22 | User Guide - Page 6
b. Wind the fiber-optic cable around the tray in the ONU-6040BF-2x. c. Connect the fiber-optic connector into the PON port. d. Put the top cover back. To avoid possible eye injury, do NOT look into an - ZyXEL ONU-6040B-22 | User Guide - Page 7
adaptor to connect this power socket to an appropriate power source. Check the LEDs (Lights) • The PWR LED turns steady on when you connect the ONU-6040BF-2x to the power supply. • The PON LNK LED turns on when the fiber connection is available. • The LAN LED turns on when the LAN - ZyXEL ONU-6040B-22 | User Guide - Page 8
Green On Connection to the optical network is up. Off Connection to the optical network is down. Blinking The ONU-6040BF-2x is trying to register to an OLT. PON Red Off STATUS The ONU-6040BF-2x is receiving good optical signals from the OLT successfully and no error signals. Blinking The - ZyXEL ONU-6040B-22 | User Guide - Page 9
is sending or receiving data at 10 Mbps. Off No Ethernet device is connected to the LAN port. Green On The ONU-6040BF-2x is receiving video signals. Off The ONU-6040BF-2x is not receiving video signals. Test Your Internet Connection After you have connected the hardware and turned on the - ZyXEL ONU-6040B-22 | User Guide - Page 10
the included stand or mounted on a wall. Standing Instructions Place the right panel of the ONU-6040BF-2x (when facing the LEDs) onto the included stand Place the ONU-6040BF-2x and the stand on a flat, level surface that is strong enough to support the weight of the ONU-6040BF-2x with connection cables. - ZyXEL ONU-6040B-22 | User Guide - Page 11
Wall-mounting Instructions Complete the following steps to hang your ONU6040BF-2x on a wall. 1. Select a position free of obstructions on a sturdy wall. 2. Drill two holes large enough for - ZyXEL ONU-6040B-22 | User Guide - Page 12
to hold the weight of the ONU6040BF-2x with the connection cables. 5. Align the holes on the back of the ONU-6040BF-2x with the screws on the wall. Hang the ONU-6040BF2x on the screws. The following are dimensions of an M4 tap screw and masonry plug used for wall mounting. All - ZyXEL ONU-6040B-22 | User Guide - Page 13
Troubleshooting 1. The PWR light is not on when I connect power to the ONU-6040BF-2x. to turn on the ONU-6040BF-2x again. • If the PWR light is still not on, use a different power outlet. • If the problem continues, contact your local your service provider to have the cable/connector replaced. Do 13 - ZyXEL ONU-6040B-22 | User Guide - Page 14
off, see 2 The PON light is off. If the PON light is on, contact your service provider and make sure the video signals can be transmitted successfully. 4. The CATV light is on connections and the lights. • There might be problems with the optical network setting. Contact your service provider. 14 - ZyXEL ONU-6040B-22 | User Guide - Page 15
(Deep) x 41 (High) < 1 kg One PON port Compliant with IEEE 802.3ah PX-10 (ONU-6040BF-21) PX-20 (ONU-6040BF-22) SC optical connectors with shutters Transmission distance: 10 km (ONU-6040BF-21) 20 km (ONU-6040BF-22) Wavelength: 1310 nm upstream and 1490 nm downstream, 1550 nm analog receiver for CATV - ZyXEL ONU-6040B-22 | User Guide - Page 16
Place connecting cables carefully so that no one will step on them or stumble over them. • Always disconnect all cables from this device before servicing or disassembling. • Use ONLY an appropriate power adaptor or cord for your device. • Connect the power adaptor or cord to the right supply voltage - ZyXEL ONU-6040B-22 | User Guide - Page 17
the product where anyone can walk on the power adaptor or cord. • Do NOT use the device if the power adaptor or cord is damaged as it might cause electrocution. • If the power adaptor or cord is damaged, remove it from the power outlet. • Do NOT attempt to repair the power adaptor or cord. Contact - ZyXEL ONU-6040B-22 | User Guide - Page 18
environment. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this device in a residential area is likely to cause harmful interference in - ZyXEL ONU-6040B-22 | User Guide - Page 19
for indirect or consequential damages of any kind to the purchaser. To obtain the services of this warranty, contact your vendor. You may also refer to the warranty .com for product news, firmware, documentation, and other support materials. Registration Register your product online to receive e-mail - ZyXEL ONU-6040B-22 | User Guide - Page 20
in this publication are used for identification purposes only and may be properties of their respective owners. Customer Support Should problems arise that cannot be solved by using this manual, you should contact your vendor. If you cannot contact your vendor, then contact a ZyXEL office for the
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
 |
 |
www.zyxel.com
User’s Guide
ONU-6040BF-2x Series
GEPON Optical Network Unit
Version 1.00
Edition 1, 5/2009
2009 ZyXEL Communications Corporation
C