ZyXEL P-794H Quick Start Guide
ZyXEL P-794H Manual
 |
View all ZyXEL P-794H manuals
Add to My Manuals
Save this manual to your list of manuals |
ZyXEL P-794H manual content summary:
- ZyXEL P-794H | Quick Start Guide - Page 1
P-794H 8 wire G.SHDSL CPE with 4 port LAN Firmware Version S04.01 Edition 1, 12/2010 DEFAULT LOGIN DETAILS IP Address: http://192.168.1.1 Username admin Password 1234 www.zyxel.com Copyright 2010 ZyXEL Communications Corporation - ZyXEL P-794H | Quick Start Guide - Page 2
Device Panels LAN LED 1-4 POWER LED ALARM DSL CO LED LED LED 1-4 CID PORT RESET SWITCH GROUNDING TERMINAL DSL PORT 1-2 LAN PORT 1-4 2 AC POWER - ZyXEL P-794H | Quick Start Guide - Page 3
things before you start. • INTERNET ACCESS: You need an Internet account with an ISP (Internet Service Provider) and information such as user name, password, and so on. • WEB BROWSER: Internet will be used to access the Internet and/or access the P-794H's Web Configurator. Hardware Connections 3 - ZyXEL P-794H | Quick Start Guide - Page 4
DSL port(s) of another P-794H. Refer to page 9 and the Tutorials chapter in User's Guide for more information about the P-794H operating in CO/CPE mode. configure the P-794H by CLI command, use a console cable to connect the CID port to your computer's COM port. This is for service technicians only. - ZyXEL P-794H | Quick Start Guide - Page 5
. Once the DSL connection is successful, the DSL lights are on. The LAN lights blink rapidly when the P-794H is sending or receiving data. If the ALM light is on, there is a connection problem.Try turning the P-794H off, check the connections, wait a few seconds and then turn it back on. If the - ZyXEL P-794H | Quick Start Guide - Page 6
and enter http://192.168.1.1 (the P-794H's default IP address) as the address. If you cannot access the Web Configurator, make sure the IP address and subnet mask of the ZyXEL Device and the computer are in the same IP address range. See your User's Guide for information on setting up your computer - ZyXEL P-794H | Quick Start Guide - Page 7
to http://www.zyxel.com. You may be prompted to enter your username and password. If the web page opens correctly, your P-794H is ready for You can manually configure the Internet connection. Log in the Web Configurator. Click Configuration > WAN Connection. Click Create a new service. 2. Select - ZyXEL P-794H | Quick Start Guide - Page 8
3. Enter a description for the connection. If your IP address is assigned by your ISP, enter it in the WAN IP addess field. If not, leave it as 0.0.0.0. Type your account username and password. Click Configure. Internet Account 4. If you are using static IP, go to Configuration > DNS Relay and enter - ZyXEL P-794H | Quick Start Guide - Page 9
the same DHCP domain but must have different IP addresses. 192.168.1.3 CPE 192.168.1.1 CO 192.168.1.4 192.168.1.2 CO Mode Log into the P-794H you are using as the CO. Click SHDSL > SHDSL Configuration and select CO in the Unit ID field. Click Apply. 9 - ZyXEL P-794H | Quick Start Guide - Page 10
CPE Mode Log into the P-794H you are using as the CPE. Click SHDSL > SHDSL CPE with the provided telephone wires. The DSL lights will be blinking. Wait for 1-2 minutes as the P-794Hs establish the connection. The DSL lights will stop blinking once the connection is successful. 2. To test the - ZyXEL P-794H | Quick Start Guide - Page 11
drop-down list box on the ZyXEL home page to go to that product's page. 3. Select the certification you wish to view from this page. For more information, please refer to the User's Guide on the provided CD or at the www.zyxel.com download library. Was this guide helpful? Send your comments to - ZyXEL P-794H | Quick Start Guide - Page 12
12 - ZyXEL P-794H | Quick Start Guide - Page 13
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
 |
 |
www.zyxel.com
8 wire G.SHDSL CPE with 4 port
LAN
Firmware Version S04.01
Edition 1, 12/2010
P-794H
DEFAULT LOGIN DETAILS
IP Address:
Username
admin
Password
1234
Copyright 2010
ZyXEL Communications Corporation