ZyXEL SFP10G-LR User Guide

ZyXEL SFP10G-LR Manual

Get ZyXEL SFP10G-LR PDF manuals and user guides View all ZyXEL SFP10G-LR manuals
Add to My Manuals
Save this manual to your list of manuals

ZyXEL SFP10G-LR manual content summary:

  • ZyXEL SFP10G-LR | User Guide - Page 1
    Guide Version 1.00 03/2012 Introduction Use a transceiver module for connection to a remote device. The SFP+ (SFP Plus) is an enhanced version of the SFP and supports chemical, photocopying, manual, or otherwise, kind to the purchaser. To obtain the services of this warranty, contact your vendor. You
  • 1
SFP+ Transceivers
User’s Guide
Version 1.00
03/2012
Use a transceiver module for connection
to a remote device. The SFP+ (SFP
Plus) is an enhanced version of the SFP
and supports data rates of 10 Gbps. The
SFP+ transceiver modules are hot
swappable. This means that you can
install and remove a module while your
device is operating. The SFP+ modules
provide duplex single-mode or multi-
mode connections.
The SFP+ module uses LC-type
connectors.
Read the following guidelines before
installing and using an SFP+ module.
Handling Warning
SFP+ modules are static sensitive. To
prevent damage from electrostatic
discharge (ESD), it is recommended you
attach an ESD preventive wrist strap to
your wrist and to a bare metal surface
when you install or remove an SFP+
module.
SFP+ modules are dust sensitive. When
not in use, always keep the dust plug on.
Avoid getting dust and other
contaminant into the optical bores, as
the optics do not work correctly when
obstructed with dust.
Safety Warning
Fiber-optic SFP+ modules are equipped
with a Class 1 laser, which emits
invisible radiation. Read the following
safety warnings carefully.
•
To avoid possible eye injury, do not
look into an operating fiber-optic
module’s connectors.
•
Laser radiation is present when the
device or system is powered up.
•
Only trained and qualified personnel
should be allowed to install or replace
these modules.
Environmental Warnings
Dispose of your fiber-optic module
according to all national laws and
regulations.
This section describes how you install
and remove a SPF+ module.
Installing an SFP+ Module
Follow the steps below to install an
SFP+ module.
1
Attach an ESD preventive wrist
strap to your wrist and to a bare
metal surface.
2
Remove the SFP+ module from its
protective packaging.
3
Locate the transmit (Tx) and the
receive (Rx) markings on the SFP+
module.
4
Align the SFP+ module in front of
the slot opening on a device.
5
Insert the SFP+ module into the slot
until the SFP+ module snaps into
place
.
Connecting a Fiber-optic Cable
Follow the steps described to connect a
fiber-optic cable to the SFP+ module.
1
Remove the dust plugs from the
SFP+ module and the cables.
2
Identify the signal transmission
direction of the fiber-optic cable and
the SFP+ module. Insert one end of
the fiber-optic cable into the SFP+
module.
3
Insert the other end of the fiber-
optic cable into a remote device.
Refer to the user’s guide that comes
with your device for SFP+ module slot
status.
Removing an SFP+ Module
Follow the steps below to remove an
SFP+ module.
1
Attach an ESD preventive wrist
strap to your wrist and to a bare
metal surface on the chassis.
2
Disconnect all fiber-optic cables
from the SFP+ module.
3
Insert the dust plug into the ports on
the SFP+ module.
4
Pull out the latch and down to
unlock the SFP+ module.
5
Using your thumb and index finger,
grasp the tabs on both sides of the
module and carefully slide it out of
the slot.
Copyright © 2012 by ZyXEL
Communications Corporation.
The contents of this publication may not be
reproduced in any part or as a whole,
transcribed, stored in a retrieval system,
translated into any language, or transmitted in
any form or by any means, electronic,
mechanical, magnetic, optical, chemical,
photocopying, manual, or otherwise, without
the prior written permission of ZyXEL
Communications Corporation.
Published by ZyXEL Communications
Corporation. All rights reserved.
Disclaimer
ZyXEL does not assume any liability arising out
of the application or use of any products, or
software described herein. Neither does it
convey any license under its patent rights nor
the patent rights of others. ZyXEL further
reserves the right to make changes in any
products described herein without notice. This
publication is subject to change without notice.
Trademarks
Trademarks mentioned in this publication are
used for identification purposes only and may
be properties of their respective owners.
ZyXEL warrants to the original end user
(purchaser) that this product is free from any
defects in material or workmanship for a
specific period (the Warranty Period) from the
date of purchase. The Warranty Period varies
by region. Check with your vendor and/or the
authorized ZyXEL local distributor for details
about the Warranty Period of this product.
During the warranty period, and upon proof of
purchase, should the product have indications
of failure due to faulty workmanship and/or
materials, ZyXEL will, at its discretion, repair or
replace the defective products or components
without charge for either parts or labor, and to
whatever extent it shall deem necessary to
restore the product
or components to proper
operating condition. Any replacement will
consist of a new or re-manufactured
functionally equivalent product of equal or
higher value, and will be solely at the discretion
of ZyXEL. This warranty shall not apply if the
product has been modified, misused, tampered
with, damaged by an act of God, or subjected
to abnormal working conditions.
Note
Repair or replacement, as provided under this
warranty, is the exclusive remedy of the
purchaser. This warranty is in lieu of all other
warranties, express or implied, including any
implied warranty of merchantability or fitness
for a particular use or purpose. ZyXEL shall in
no event be held liable for indirect or
consequential damages of any kind to the
purchaser.
To obtain the services of this warranty, contact
your vendor. You may also refer to the warranty
policy for the region in which you bought the
support_warranty_info.php.
Introduction
Handling, Safety and
Environmental Guidelines
Note:
Class 1 Laser Product.
Appareil A` Laser De Classe 1
Laser Produkt Der Klasse 1.
Installing and Removing an
SFP+ Module
Note:
Disconnect all fiber-optic cables
from an SFP+ module before installing
or removing it.
Do NOT remove and install an SFP+
module more often than is absolutely
necessary. Doing so may shorten the
useful life of the SFP+ module.
Note:
SFP+ module installation
orientation varies depending on your
device. Your SFP+ module comes with a
mechanism that prevents incorrect
insertion. Do NOT force or twist the
SFP+ module into a slot. Do NOT insert
the SFP+ module into a 1-Gigabit SFP
slot.
Note:
Do NOT force or twist the module
out of a slot.
Copyright
ZyXEL Limited Warranty